vfr 800 vtec electrical diagram

You search Auto repair manual PDF vfr 800 vtec electrical diagram, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vfr 800 vtec electrical diagram Direct Download speed 5282 Kb/s

  vfr 800 vtec electrical diagram Full Version speed 6162 Kb/s



2002 Honda VFR 800 VTEC Power Commander 111-210 Installation Instructions

0

Filed Under (Honda) by admin on 26-11-2011

download
If you feel that you are having any problems at all with the Power Commander II, disconnect it from your motorcycle. This will allow the motorcycle to run directly off of the stock ECU. The lights don’t come on when I turn the ignition switch on.
Check to make sure connectors are seated and the kill switch is in the “run” position. The on-board adjustment buttons do not hold their settings. Be sure to wait 20-30 seconds after making adjustments before starting or turning off the bike.
Can not upload to or download from the Power Commander II. Check to see that the serial cable is firmly in place. Verify that ignition switch is on and the kill switch is in the “run” position. My mouse uses the same serial port. If your computer has a PS/2 port purchase a DB9 to PS/2 adapter for your mouse. I get a “verify failed….” message when I upload a map to the Power Commander II. Programs running in the background or fluctuations in supply voltage (from outlet) can sometimes cause this error. In most cases, the information was sent properly to the Power Commander II. Pushing
the “upload all” button again should produce a “tables sent and verified” message. I typed in notes, but they didn’t save.
You need to first push the “accept” button in the notes window and then the “save file” button.

Incoming search terms:

Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles Owner's Manual

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. Disconnect the negative battery cable. 2. Grasp the sides of the electrical caddy (located next the ignition coil) and pull outward to remove. 3. Remove the relay and fuse panels from the electrical caddy. a. Insert a small screwdriver into the slot under each fuse and relay panel. b. Using a screwdriver, disengage the panel from the electrical caddy. 4. Disconnect the main fuse connector from the electrical caddy a. Remove the main fuse from the connector b. Insert small screwdrivers into the slots on each side of the main fuse c. Depress the tabs of the main fuse connector to disengage it from the electrical caddy
Thunder Heart Performance Corp. 615-672-8811 www.thunder-heart.com 2 EI5075.doc 5. Depress the tab located on the electrical caddy securing the TSM/TSSM. Pull it from the electrical caddy. Disconnect the TSM/TSSM connector. 6. Slide the data link connector towards the front of the motorcycle to disengage it from the electrical caddy. 7. Disconnect the ignition control module connector. 8. Disconnect the ignition coil connector and spark plug cables from the coil. 9. Remove the electrical caddy fasteners (3 total). 10. Remove the wiring from the electrical caddy. 11. Remove the fasteners securing the factory ignition control module from the electrical caddy. 12. Installation of the Digital Ignition Module is the reverse of removal. 2.2 Touring Models 1. Disconnect the negative battery cable. 2. Remove the right saddlebag. 3. Gently pull the side cover from the frame downtubes (no tools required). 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. Remove the two socket screws to detach the ignition control module from the electrical bracket. 6. To install the Digital Ignition Module, install and tighten the socket screws to 50-60 in-lbs . The remainder of installation is the reverse of removal. 2.3 Softail Models 1. Remove the seat. 2. Disconnect the negative battery cable. 3. Remove the two screws to free the ignition control module from the mounting bracket. 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. To install the Digital Ignition Module, install and tighten the socket screws to 15-21 in-lbs . The remainder of installation is the reverse of removal

Incoming search terms:

2002-2007 HONDA VFR 800 WITH ABS GALFER BRAKE LINE KIT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 03-03-2011

download
Prep the motorcycle for this job A. Park motorcycle on the center stand in a well-lit shop (Fig.A) B. Note: it is not absolutely necessary to remove the fuel tank and body panels. However, brake fluid is VERY CORROSIVE TO PAINT. We decided to be safe (Fig. B) and removed the lower fairing left and right rear sides, fuel tank, front fender, seat, and black A B plastic inner fairing front parts, battery cover, and rear master cylinder cover according to the owner’s manual. This also gives better access to the fittings. (Fig C) C. After safely storing the body panels and fuel tank, remove wind shield, (brake fluid, even a drop, will permanently mark any clear plastic), cover the dash and all gauges with a towel. II. Draining the brake fluid from the systems. A. A copy of the factory instructions has been included with this kit on how to properly and safely drain, fill and bleed the brake fluid from the brake systems. Follow the directions closely and remove the fluid according to the instructions. Dispose of the old fluid properly—DO NOT REUSE. B. If you purchased the clutch line, then perform the following steps (Fig D): In the bag marked Clutch Line: remove the left side lower body panels. Remove vehicle speed sensor, and remove the coolant C D tank. Remove the clutch fluid from the master cylinder on the left clip-on. Remove the fluid from the clutch line and slave cylinder. This factory line is NOT attached along the inner frame spar so here is a little trick that made this a 20- minute job including the bleed: 1. Remove the banjo bolts from the master cylinder and the clutch slave ends. 2. With a nice heavy wire tie, attach the slave end of the new braided line to the lever end of the factory line. Snip off the tail of the wire tie. Wrap this “joint” with electrical tape. 3. Pull from the factory slave end until you get the braided line end to the clutch slave. If it gets caught on something, try turning the end you are pulling from. 4. Remove the tape, carefully cut off the wire tie, install new sealing washers and bolts at both ends and torque to 17-21 foot/lbs. maximum. Bleed the clutch. III. Removing the factory front brake hoses and calipers – Front A. With the fluid drained and disposed of properly, loosen the bolts that hold the right caliper to the right fork leg (Fig E). Also remove the two 8mm bolts from the ABS front wheel speed sensor. Loosen all of the hose mounting blocks on the front forks on both sides; also loosen the blocks for the crossover pipe (Fig F) between the fork legs. Also loosen the frame pipe mounts and the mount for the front lever line that is also E attached to the right side of the frame. Loosen the left caliper mounting bolts (Fig G). B. Remove the calipers and remove the hose mounts under the lower triple tree. Remove the hard pipes from both the left and right hard pipe to soft line frame mounts on the frame (Fig. H). On the front ABS modulator remove the short soft line that is connected to the mount block. (Fig I.a. & I.b.) C. Carefully remove the

Incoming search terms:

2002-2007 HONDA VFR 800 NSTALLING GALFER BRAKE LINE KIT

0

Filed Under (Honda) by admin on 08-12-2011

download
Remove the clutch fluid from the master cylinder on the left clip-on. Remove the fluid from the clutch line and slave cylinder. This factory line is NOT attached along the inner frame spar so here is a little trick that made this a 20- minute job including the bleed: 1. Remove the banjo bolts from the master cylinder and the clutch slave ends. 2. With a nice heavy wire tie, attach the slave end of the new braided line to the lever end of the factory line. Snip off the tail of the wire tie. Wrap this “joint” with electrical tape. 3. Pull from the factory slave end until you get the braided line end to the clutch slave. If it gets caught on something, try turning the end you are pulling
from.4. Remove the tape, carefully cut off the wire tie, install new sealing washers and bolts at both ends and torque to 17-21 foot/lbs. maximum. Bleed the clutch

1998-2001 HONDA VFR 800 Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 14-12-2011

download
Identify the key components that complete our brake line kit: You should have nine (9) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) single bleeder bolt three (3) drawings, and a picture CD. There are also a total of forty (40) washers and two (2) “olive” conic inversors. Thirty six washers will be used, and two olives. The rest are spares.Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G are installed on the front of the motorcycle, while brake hoses (H and I) are installed on the rear. Each label will reference a different drawing, which will show you the location of the key brake system
components.Step 3: To ensure no paint damage from a brake fluid spill, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a couple pictures, in case you need to re-install. Step 4:Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G. Locate lines A. this hose will run from the master cylinder down to the right caliper and across the fender through the C-CLIP down to the left caliper. Line D. will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame female fitting will thread into the male with a (OLIVE) this O.E.M tubing travels to the proportion valve. Line F will run from the left caliper up through the C-CLIP to the left upper frame female fitting and thread to the male with a (OLIVE) this tubing travels to the rear master cylinder. Locate and install line E; this hose will run from the lower delay valve down to the right caliper. locate and install line C& G; line G will travel from the bottom (left) mounting point on the left caliper, to the upper inner mounting point of the left caliper this line joins line C with a double banjo bolt. line C will travel from the inner left caliper through the C-CLIP across the front fender to the inner mounting point of the delay valve

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

Incoming search terms:

BMW Motorcycle F 650 GS/ F 800 GS Accessories

0

Filed Under (BMW) by admin on 20-11-2010

download
Stowage-equipment line Vario case, black, left 71 60 7 696 299 £184 / G Vario case, black, right 71 60 7 696 300 £185 / G (+) Case carrier for Vario case, including fasteners 71 60 7 696 301 £144 / G (+) Lock barrel, complete, for 2 cases 51 25 7 688 566 £20.80 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 2x) 51 25 7 681 199 £33.59 (o) Lock-barrel set 51 25 7 698 202 £15.20 / I Liner for Vario case, left 71 60 7 687 610 £67 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Vario topcase, black 71 60 7 696 302 £225 / I (+) Luggage rack, large, for Vario topcase (including adapter plate) 71 60 7 696 303 £64 / I (+) Lock barrel for topcase 51 25 7 688 568 £12.50 / I (o) Lock barrel by code for vehicle and/or case matching locks (order 1x) 51 25 7 681 199 £33.60 / I (o) Lock barrels for 2 cases and topcase 51 25 7 688 567 £29.10 / I Liner for Vario case, right, and Vario topcase 71 60 7 687 611 £67 / I Backrest pad for topcase 71 60 7 688 877 £45 / I Luggage carrier, small 71 60 7 701 810 £42.90 / G Tank rucksack, waterproof 71 60 7 711 240 £130 / I Enduro rear softbag 71 60 7 711 245 £35.90 / I Sport softbag, small, 19 l 71 60 7 694 117 £102 / I Sport softbag, large, 51 l 71 60 7 693 567 £139 / I Stuffbag, waterproof, 53 l 72 60 7 653 818 £90 / I Luggage strap with pull-tight buckle 72 60 2 304 808 £6.30 / E Bungee-cord spider 72 60 9 057 579 £3.95 / E Design line Spray-guard extension, rear 71 60 7 695 031 £24.20 / I Sound components Akrapović sports silencer 71 60 7 713 339 *1 £475 / G Ergonomics and comfort line Windscreen, large, tinted 71 60 7 713 834 *1 £138 / I Windscreen, large, clear (standard for F 800 GS) 71 60 7 713 833 £127 / I Windscreen, small, clear (standard for F 650 GS) 71 60 7 713 296 £87 / I Centre stand (F 650 GS) 46 52 7 700 864 *2 £83 / I Centre stand (F 800 GS) 46 52 7 700 049 *2 £91.50 / I (+) Fasteners for centre stand (F 650 GS + F 800 GS) 71 60 7 706 738 £24.90 / I Seat, low, black, 790 mm (F 650 GS), 850 mm ( F 800 GS) 52 53 7 695 013 £174 / I Heated handlebar grips and switches (see electronic parts catalogue) Navigation and communication components BMW Motorrad Navigator III plus 2008 72 60 7 716 116 *1 £650 / I (+) Holder for BMW Motorrad Navigator 71 60 7 697 785 £45.80 / E (+) Securing screw (order 4 of) 32 71 7 652 161 £4.55 / I Connecting cable for BMW Motorrad Navigator 71 60 7 686 670 £55 / E TMC module for BMW Motorrad Navigator 72 60 7 702 687 *1/3 £111 / E Car kit for BMW Motorrad Navigator 72 60 7 703 996 *3 £60.50 / E Navigator carry-bag function 71 60 7 683 161 £49 / I Safety line Hand-protector bar 71 60 7 716 043 £57 / I (+) Countersunk-head screw (order 2 of) 32 71 7 712 836 £3.34 / E Hand protector, small 71 60 7 705 963 £19.50 / I Hand protector, large 71 60 7 715 135 £23.10 / I Protector-mounted spoiler for hand protector, large 71 60 7 705 964 £15.20 / I Crash bar, left 71 60 7 699 437 £104 / I Crash bar, right 71 60 7 699 438 £104 / I (+) Fasteners for crash bar 71 60 7 702 395

Yamaha XVS13AW SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3-1 3 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10540 ON All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed. NOTE: The headlight comes on automatically when the engine is started and stays on until the key is turned to “OFF”, even if the engine stalls. EAU10660 OFF All electrical systems are off. The key can be removed. EAU10680 LOCK The steering is locked, and all electrical systems are off. The key can be re- moved. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. WARNING EWA10060 Never turn the key to “OFF” or “LOCK” while the vehicle is moving, otherwise the electrical systems will be switched off, which may result in loss of control or an accident. Make sure that the vehicle is stopped before turning the key to “OFF” or “LOCK”. 1. Push. 2. Turn. 1. Push. 2. Turn. INSTRUMENT AND CONTROL FUNCTIONS 3-2 3 EAU11003 Indicator and warning lights EAU11020 Turn signal indicator light “” This indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU42740 Fuel level warning light “” This warning light comes on when the fuel level drops below approximately 3.7 L (0.98 US gal) (0.81 Imp.gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, and then go off, have a Yamaha dealer check the electrical circuit. NOTE: The vehicle must be on a level surface and positioned upright, otherwise the fuel level warning light may not come on and go off at the appropriate times. This model is also equipped with a self-diagnosis device for the fuel level detection circuit. If the fue

Incoming search terms:

TRAILER ELECTRICAL ISOLATOR Installation Procedures

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Control circuit connections to the motorcycle (normally under the seat or trunk): #1 Brownwireshould be connected to the taillight circuit. #2 Green/Redshouldbe connected to the brake light circuit. #3 LightBlueshould be connected to the left turn signal circuit. #4 Orangeshouldbe connected to the right turn signal circuit. #5 Greenwireshould be connected to frame ground (not to the battery negative post) #6 Yellowwire should be connected to positive 12 volt battery supply. TRAILER ELECTRICAL ISOLATOR WARRANTY -Krissproductsare covered under our standard limited warranty Items returned for inspection must have prior return authorization from the factory. All items must be sent freight prepaid. We are not responsible for any item returned without authorization. Technical assistance is available on the Internet. All items returned for inspection and found to operate properly will be subject to a minimum testing fee. Complete details of our limited warranty maybe found on our internetpages. for defective materials and workmanship. NOTE: Please observe standard good installation procedures by not placing or attaching electrical devices next to plastic decorative outer panels or fairings to prevent damage due to heat. Electricity can produce high temperatures in the event of short circuits. KRISS INDUSTRIESINC. wwwkriss.com . Techinical Support Warranty Assistance Product Information Contact Information KRISS MOTORCYCLE PRODUCTS Installation Procedures Use a test light to identify the correct circuits. If you do not have the proper tools or knowledge to identify the proper wiring we suggest that you seek professional assistance locally. Please note that we are notable to provide telephone or email installation and/or electrical training

SUZUKI 1400/ 800 INTRUDER TURN SIGNAL RELOCATION INSTALLATION AND CLEANING INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-11-2010

download
1. Refer to Figure 1. 2. Remove seat. Safety: disconnect battery prior to all wiring modifications LeatherLyke 510 5/1/2009 3. Disconnect wires to turn signals. 4. Remove turn signals and retain hardware for reinstallation. Observe and mark “left” and “right” for reinstallation. Information: Do not remove license plate bracket . 5. Remove license plate. Turn signal bracket must be oriented with flange (side with only 2 holes) on top. 6. Install turn signal bracket behind license plate bracket and license plate using 6 x 35mm pan phil machine screws for the 800 or 6 x 20mm pan phil machine screws for the 1400, 1/4″ flat washers, and 6mm locknuts. Insert black spacer spool between license plate bracket and turn signal bracket. 7. Mount turn signals directly to turn signal bracket using 6 x 10mm hex cap screws and star lock washer. Information: Observe all color-coding of wires and splice one wire at a time. 8. Cut each turn signal wires three inches from end and splice 10 inches of supplied wire. Secure wires to inner fender clips. 9. Follow route of tail light wires and connect wires into harness. 10. Secure wires together behind license plate bracket with tie wrap. 11. Connect battery and test turn signals for function. 12. Install seat. Information: Not all license plate mounts are grounded. In some cases, it may be necessary to run a ground wire to turn signal bracket. WARNING: States may have minimum width requirements on motorcycle turn- signals, so check your local laws. LeatherLyke 510 5/1/2009 SADDLEBAG INSTALLATION 13. Refer to Figure 2. Information: Cover plates are pressed into strut. 14. Remove round cover plate at end of fender mount strut on right side. 15. Remove nut on right rear and replace with 1.2″ hex adapter. If hex adapter is less than flush with the outside of both fender struts, add a 5/16″ flat washer. 16. Assemble 5 x 30mm flathead screw and 5mm mounting spool with chamfer on spool under head of screw. Insert assembly thru 1 1/4″ fender washer for the 1400 or 1″ for the 800. 17. Install spool assembly into previously installed 1.2” hex adapter. Information: Do not remove washer on shock absorber. Hex adapter will protrude 1/4″ beyond fender strut. 18. Remove round cover plate over right rear shock, remove shock absorber nut and install .75″ hex adapter. 19. Assemble 5 x 30mm flathead screw, mounting spool and cup washer with chamfer on spool under head of screw. 20. Install spool assembly into previously installed hex adapter. 21. Insert 5/8” finishing plug into old turn signal hole on right side. 22. Repeat procedures on opposite side

Incoming search terms:

Incoming search terms: