victory vision arm rest mounts

You search Auto repair manual PDF victory vision arm rest mounts, if there are search results will appear below. If search results do not exist, please search by others keyword.





HONDA VT 1100 HIGHWAY MOUNTS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the parts supplied from the package and lay them out in front of you. Remove the screws from the mounts and clamps. See photo (1), notice that the two clamp halves (1A) and the two arms (1B) are the same. Notice that the two mounts (1C) are different and are machined at opposite angles. The mounts (1C) can be installed facing forward to the front of the bike as shown in photo (1) or facing to the rear of the bike as shown in photo (2) depending on how far forward you want the pegs to be located. 2. Starting on the right side choose which way you want the mount to face. Hold one of the mounts up against the frame tube. Hold one of the arms up against the mount where it bolts together. The arm should be horizontal or level when the bike is sitting up straight. If not use the mount with the opposite angle. Next while still holding the mount in place at the desired location place one of the clamps behind the mount and start the screws. Snug the screws only leaving them loose enough to make further adjustments later. Next Bolt one of the pegs loosely to the arm as shown in photo (2). Notice that there are eight dowel pin holes on the mount and seven on the back side of the arm allowing 56 possible angles or positions for the arm to be set at. Holding the arm/peg assembly up to the mount select the desired position for the arm and place one of the dowel pins supplied into the nearest set of holes on the mount and arm. Bolt the arm/peg assembly to the mount using one of the large button head Allen screws and a washer provided. Once you have the arm close to where you want it you can make fine adjustments by removing the large Allen screw, removing the arm and moving the dowel pin to the next hole in the mount. Moving the pin clockwise one hole will rotate the arm in the opposite direction approximately ½”. Likewise moving the pin counter clockwise will rotate the arm in the opposite direction. 3. Repeat this procedure on the left side. Sit on the bike. Place your feet on the highway pegs and verify that you have them set at the most comfortable position for you and that they are set the same on both sides. Tighten all bolts and screws securely

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

Installation Instructions Highway Mounts for Engine Guards

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Loosely assemble the mount and clamp onto the engine guard tube. Without lowers the arm may be mounted on the inside or outside of the crash bar, with lowers it must be mounted on the outside only. Next assemble the bolt, washer, arm & locking pin as shown. Note: You may want the arms to lean outward slightly to give more room for your legs around the fairing lowers. Tighten the front screws securely.(side without the gap) Then the rear. Adjusting the arm angle. Notice that there are 8 locking pin holes in the mount and 7 in the arm. By leaving the pin in the mount and rotating the arm to its next hole will move the arm 50 deg. When you get close to the desired angle you may make adjustments in 5 deg. increments by moving the pin to the next hole in both the mount and the arm. Moving to the next set of holes clockwise will move the arm counter clockwise 5 deg. Moving the pin to the next set of holes counter clockwise will move the arm clockwise 5 deg. This will provide 72 different mounting angles total. Install the large bolt and washer, tighten securely and install your pegs or hi-way boards . Note: When installing boards put the lock or star washer between the board and the arm to prevent them from rotating under heavy pressure.

Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

SUZUKI M109 ADJUSTABLE HIGHWAY PEG MOUNTS Installation Instructions

0

Filed Under (Suzuki) by admin on 29-12-2010

download
1. Starting on the left side of the motorcycle remove the two 14mm bolts that attach the left foot peg and shifter mounting bracket to the frame. Locate the longer two of the (4) supplied mounting bolts supplied, place a lock washer first and then a washer on each. Locate the left curved main mount (it will have its polished chrome side and the circle of dowel pin holes facing outward when installed on the left side). Place the bolts thru the bolts thru the holes in the mount the slide a spacer (supplied) over each bolt. Place the mount with the bolts and spacers thru the holes of the foot peg and shifter mounting bracket removed earlier and thread the bots into the frame then tighten securely 2. Repeat this procedure on the right side using the remaining shorter bolts, lock washers, washers, mount and spacers and again tighten securely. 3. Again starting on the left side install one of the dowel pins supplied into any of the holes in the mount, place one of the remaining mounting arms (they are the same left and right) onto the dowel pin that is closest to the position you want the arm to be in. Place one of the washers onto the large allen screws then thru the finished side of the arm and thread it into the center hole of the mount. 4. Repeat this procedure on the right side. Loosely install the foot peg set you have selected onto the arms. Sit on the motorcycle to see if you are comfortable with the position you have chosen. You can adjust the position of the arms in Ω” increments forward or back as follows. Remove the arm while leaving the pin in its hole, now move the pin to the next hole forward to rotate the arm back towards the rider Ω” or into the next hole back to rotate the arm forward Ω” and re-install the arm into the corresponding hole that is in the direction you want the arm to go. 5. Adjust the angle of the foot pegs so that they are both comfortable to your feet and will fold up and to the rear when not in use. Set the peg pivot bolts tight enough to hold the in the folded position but loose enough so that you can fold them down with your foot when you need them. Recheck all fasteners for tightness.

Incoming search terms:

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

YAMAHA ROADLINER AND STRATOLINER PASSENGER FLOOBOARD RELOCATION ARMS

0

Filed Under (Yamaha) by admin on 23-12-2010

download
1. When installing floorboards at the same time first refer to their instructions and using the longer right side black floorboards mounting block supplied with this set of relocation arms. Leave the final floorboards mounting bolt installed loosely at this time. 2. If installing the relocation arms after installing the floorboards at an earlier date proceed as follows. 3. On the left side remove the Allen screw below the floorboards pivot and remove the floorboard from the black mounting block. Remove the dowel pins from their holes on the block. Locate the left relocation arm (stamped “L” and “R” on their backsides). On the end with the clearance hole (not threaded) Place the two dowel pins into one of the two sets of holes which are directly across from each other (180 degrees apart). Hold the arm with the dowel pins up to the mounting block. Align the dowel pins with each of the three sets of holes in the block one at a time noting the height of the opposite end of the arm where the floorboard will mount. Move the dowel pins to the other set of holes on the arm and again hold the arm with the dowel pins up to the blocks three sets of holes. Choose the set of holes in both the block and arm which will set the floorboard to the desired height and place the arm with the dowel pins onto the block. Using one of the button head Allen screws supplied bolt the arm to the block and tighten securely. 4. Locate two of the dowel pins supplied and one of the Allen screw removed earlier. Place the dowel pins into the holes of the arm which allow the floorboard to be level or parallel to the ground. Place a drop of loctite on the threads of the screw and tighten securely. Install the right floorboard in the same manner. 5. On the right side remove the floorboard from the mounting block. Remove the mounting block and replace it with the longer one supplied. Install the right arm in the same manner as the left using the set of dowel pin holes to match the height or angle of the left arm. Install the right floorboard and tighten securely. Recheck all fasteners for tightness.

Incoming search terms:

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

Incoming search terms:

Victory vision ENGINE SPECIFICATION

0

Filed Under (Victory) by admin on 13-11-2010

download
Type: Air/oil-cooled SOHC 4-valve-per- cylinder 50° V-twin 4-stroke Displacement: 1731cc Compression ratio: 9.4:1 Bore x stroke: 101 x 102mm Starting system: Electric Engine management: Electronic ignition Fuel system: Electronic fuel injection with 45mm throttle bodies Clutch: Wet multiplate Transmission: 6-speed Final drive: Belt FRAME Type: Tubular steel Swingarm: Aluminium Front suspension: Conventional 43mm dia. telescopic fork Rear suspension: Linkage-type w/single gas-charged shock absorber, air adjustable Brakes: Linked system comprising twin 300mm rotor floating discs with 3-piston calipers up front & single 300mm floating rotor with 2-piston caliper rear Wheels: Cast aluminium 18 x 3.0 in. front & 16 x 5.0 in. rear Tyres: Dunlop Elite 130/70R18 front & 180/60R16 rear DIMENSIONS Wheelbase: 1670mm Rake/Trail: 29°/137mm Seat height: 673mm Dry weight: 365kg Fuel tank capacity: 22.7The engine is reasonably quiet and remarkably smooth in cruise mode. It has the lovely pulse that a massive V-twin develops when you gas it up, but on cruise it takes a conscious effort to find even the slightest tick from the donk. I was incredulous at times. The range on a tankful varied with how sportily I pushed the bike along, but it was about ‘big tourer’ standard. It rides harder than you might expect; it’s an enjoyable bike to toss around too. Stopping is taken care of by a set of three 300mm discs, twin floating rotors with three-piston calipers up front and one two-piston unit aft. They are linked, provided good feel and were confidence

Incoming search terms:

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms: