viedo on where to apply anti sieze on motor cycle axle

You search Auto repair manual PDF viedo on where to apply anti sieze on motor cycle axle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  viedo on where to apply anti sieze on motor cycle axle Direct Download speed 5282 Kb/s

  viedo on where to apply anti sieze on motor cycle axle Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL CHROME REAR AXLE ADJUSTER AND COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Block the motorcycle underneath the frame so the weight of the vehicle is off of the rear wheel, but do not raise the rear wheel off the ground. 2. Some models require loosening or removal of the muffler or mufflers in order to remove the rear axle. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. Remove the saddlebags if desired for extra working clearance. See SADDLEBAG REMOVAL in the Service Manual. 3. See Figure 1. Remove the original axle adjustment bolts (1) and jam nuts (2) from both sides of the motorcycle and discard. NOTE On a bike that has been previously serviced, ensure that the axle has not been removed and re-installed from the left side (with the castle nut to the right of the wheel). If it has, the axle MUST be inserted from the right side of the motorcycle. 4. Remove the retaining pin (7), castle nut (5) and washer (4) from the left side of the axle (6). Discard the washer, but save the pin and nut for later re-assembly. 5 7 1 4 6 2 3 is04101 1. Axle adjust bolt 2. Jam nut 3. Axle adjuster collar 4. Washer 5. Castle nut 6. Rear axle 7. Retaining pin Figure 1. Rear Axle Hardware (Left Side Shown) 5. Tap the axle toward the right side of the motorcycle and remove. The belt adjuster collars (3) will fall loose as the axle is removed. The collars can be discarded. The wheel bearing spacers may also fall loose or be dislodged. Be sure to return these to their original position on the vehicle (short spacer on the right side, long spacer on the left). 6. Inspect axle components for damage or excessive wear, and replace as required

Incoming search terms:

HARLEY DAVIDSON SOFTAIL REAR AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. 1988-1999 FLSTF Models: Remove rear muffler heat shield, loosen rear exhaust Torca clamp, then remove rear muffler from support following the instructions in the appropriate Service Manual. 2000 and Later Models: Remove exhaust system following the instructions in the appropriate Service Manual. NOTE In some cases, if bike has been previously serviced, the axle may have been removed and re-installed from the left side (with castle nut and cotter pin on the right). If this is the case, the axle must be removed and installed from the the right. If axle appears as original configuration (as in Figure 1), it is not necessary to loosen the rear axle nut or remove the cotter pin (or spring clip) from the rear castle nut. 2. All Models: See Figure 1. On the left side of the motorcycle, loosen the axle adjuster screw (1) and jamnut (2) just enough to be able to remove the jamnut. 3. 1988-1999 FLSTF Models Only: See Figure 2. On the right side (brake caliper side), use a T40 TORX drive to remove the two pin bolts from caliper. Remove caliper by gently rocking caliper back and forth to compress caliper piston, then carefully slide caliper off brake disc. Use cable strap or other suitable means to support caliper. 4. All Models: On the right side, loosen the axle adjuster screw and jamnut just enough to be able to remove the jamnut. 5. All Models: See Figure 3. On each side, place retainer clip (oriented as shown) and washer from kit over axle adjuster screw and replace jamnut. Turn in axle adjuster screw until it is in its original position against axle spacer, but leave jamnut loose. 1 2 4 3 is04788 1. Axle adjuster screw 2. Jamnut 3. Castle nut 4. Cotter pin (or spring clip) Figure 1. Rear Axle Hardware

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

CL-1000 CONDOR CYCLE LOADER USER INSTRUCTION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Confirm that the cradle is set in the optimized position setting (See RECOMMENDED CRADLE SETTINGS) for the entering tire and wheel. Adjustment of cradle is crucial for optimum retention. Optimum retention is achieved by trying different settings. ( REFER TO CAUTION PARAGRAPH BELOW ): If the optimum vertical support is achieved, the motorcycle will hold itself upright. If optimum retention is not achieved try different cradle settings. ( REFER TO CAUTION PARAGRAPH BELOW ). Once cradle is positioned, tighten the brakes using the eye bolts and place the Cycle Loader in front of the motorcycle. Push or drive the motorcycle, centered into unit, until the cradle of the Cycle Loader has fully engaged the wheel. Once the wheel is cradled, proceed to push further into the Cycle Loader until the wheel has engaged the front stop. If the optimum vertical support is achieved, the motorcycle will hold itself upright. As an extra precaution, an optional Velcro strap may be used to strap the cradled wheel to the front stop (Optional Velcro strap purchased separately). Always strap Velcro through the wheel and around the front stop below the upper front stop flange. Loosen the brakes and use two (2) tie-down straps to secure the motorcycle to the two front eyebolts of the Cycle Loader. Hook wench to Ω” ‘U’ hook in front of Cycle Loader. Use the wench to pull the Cycle Loader with motorcycle up the flat bed. Once the motorcycle is all the way on the flat bed, the bike should be secured to the flat bed itself. For more information on use, refer to www.condor- lift.com. RECOMMEDED CRADLE SETTINGS: The Condor® Cycle Loader is designed so that for every tire/wheel size within the ranges specified a minimum of 2 cradle settings is suitable. **The optimum cradle setting for a specific tire would be, the setting that allows the cradle to tilt flush with the unit/ or º” below the opening in the main unit where the cradle sits, without touching.** The 2nd optimum setting would be the setting forward from the optimum setting away from the entry direction. If less retention is desired at any time due to too much retention or sticking, the cradle may be moved away from the entry direction one notch. RACING APPLICATIONS: For bikes with GP or low durometer front tires compounds, use the 5th cradle setting from the entry directions. CAUTION: Always make sure that all fasteners are tight and all pins are in place prior to use. Understand the limitations of this product and do not exceed these limitations. Always make sure that the unit’s cradle settings are optimum for the tire size of the motorcycle before use. For bikes with very low fenders and or cowlings, a custom cradle may be purchased fitted to specific tire sizes, so as not to make contact. For standard sport bike front wheel combinations, the 1, 2, 3, front settings may be suitable. If instructions are not clear, additional information is available at www.condor-lift. com or call 1-800-461-1344. Technical Components Development & Design is not responsible for any damage incurred by exceeding this product’s limitations in structure and/or functionality.

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

Commonwealth of Massachusetts Registry of Motor Vehicles Motorcycle Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
DEFINITIONS MOTORCYCLE Any motor vehicle having a seat or saddle for the rider that is designed to travel with no more than three wheels contacting the ground, including any bicycle with a motor or driving wheels attached. MOTORIZED BICYCLE A pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty (30) miles per hour (mph) . OPERATION OF MOTORIZED BICYCLES Under Massachusetts law, mopeds fall into the category of “motorized bicycles”(with or without pedals) and are therefore regulated by the Registrar of Motor Vehicles. Individuals must have a valid learner’s permit or driver’s license to operate a motorized bicycle or moped. Mopeds must have automatic transmissions and cylinder capacities of no more than 50 cubic centimeters. In addition, mopeds must meet all federal motor vehicle safety standards and have maximum speeds of no more than 30 mph. The following limitations apply:  Individuals may not operate at speeds greater than 25 mph;  Individuals may not operate on state highways or limited- access roads with signs prohibiting bicycles;  Individuals may not operate on off-street recreational paths;  Individuals may use bicycle lanes along roadways;  Individuals must use the proper hand signals before stopping or turning;  Individuals and their passengers must wear United States Department of Transportation (US DOT) approved helmets when operating;  Individuals may not carry passengers while operating on a permit.

HONDA VT-600 Front Wheel Adapter kit Installation Instructions

0

Filed Under (Honda) by admin on 10-11-2010

download
1. Using a 6mm Allen wrench, loosen the 2 front axle pinch bolts on the right side of the lower fork leg. Loosen bolts 4 or 5 turns. 2. Using a 17mm Allen wrench, slightly loosen the front axle from the right side of the bike. Having the front wheel on the ground will help you in loosening the axle. Do not remove the axle at this time! 3. Loosen and remove the speedometer cable from the back of the speedometer on your handlebars. Pull the speedometer cable all the way out of the front fork. Remove the cable from the speedometer drive on your front wheel (note the position of the connection as it will be similar on your new drive installation). This speedometer cable or speedometer drive will not be needed on your new wheel installation. 4. Block the back wheel to prevent the bike from rolling backwards, and raise the motorcycle’s front wheel off of the ground, so the wheel spins freely. You can do this with a motorcycle lift placed under the front portion of the motorcycle frame. Contact Scootworks to purchase a lift if you don’t have access to one. Ensure the bike is stable and will not fall before proceeding further! Scootworks, Inc. 3 5. Using the 17mm Allen wrench, finish loosening the front axle until it is completely free from the left side of the lower fork. Hold onto the front wheel and slowly remove the axle from the front fork. Be careful not to let the wheel drop. Having a helper hold the wheel for you as you remove the axle will ease the removal. Slide the brake rotor out of the calipers. NOTE: be careful not to operate the front brake controls with the brake rotor removed from the calipers. 6. With the wheel removed from the front forks, lay the wheel on a padded or cushioned surface with the brake rotor facing upwards. Using a 6mm Allen wrench, remove the 5 Allen bolts from the brake rotor. (The bolts are sometimes installed with loctite, and may require heating with a small torch to loosen the loctite). Remove the brake rotor from the wheel. Place the wheel to the side. Clean up the bolts as you will reuse them later. 7. Take your new custom wheel that you will be installing on your bike and place it on a cushioned or padded surface to prevent scratching. Turn it so that the side where the brake rotor attaches is facing upward. 8. Ensure the brake rotor mounting holes on the wheel are clean and free of oil or grease. Clean with alcohol if needed, then let dry. Place your new brake rotor adapter plate onto the wheel with the flat side against the wheel. Apply a small amount of medium strength (blue) loctite on each of the 5/16″ Allen bolts supplied with your kit and install through the new rotor adapter plate and into the wheel. Tighten with a 3/16″ Allen wrench until snug. When all bolts are installed, tighten in a star pattern, and torque to 25-30 ft. lbs. 9. Install your brake rotor onto the new brake rotor adapter using the original bolts you removed in step 6. Apply a small amount of medium strength loctite to each bolt and install through the brake rotor into the new brake rotor adapter. Tighten in a star pattern, and torque to 25-30 ft. lbs. 10. It is now time to install your new wheel/rotor adapter onto your bike. It is easiest to accomplish this with a helper, as it takes some coordination to get the wheel, brake rotor and spacers into place. Apply a thin coat of grease to the axle. Lift the front wheel into place between the front forks, aligning the brake rotor into the caliper. The caliper floats from left to right and can be moved into the proper position. If the caliper is closed, pry the brake pads apart so that the rotor will slide into the caliper.

Incoming search terms:

HARLEY DAVIDSON DYNA REAR AXLE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Models This kit fits 2006 Dyna models. This kit does not fit on motorcycles equipped with saddlebags. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Place axle covers in position over ends of swingarm with the deeper cover on the left side (covering the axle nut). 2. Fasten the clamping bars (3) to the backs of the covers using hex-head screws (5) and Belleville washers (4), securing the covers to the swingarm. Tighten the hex-head screws to 21-27 in-lbs (2.4-3.0 Nm) . Do not overtighten SERVICE PARTS 4 1 3 4 5 2 3 5 is00709 Figure 1. Service Parts: Dyna Swingarm Axle Cover Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 45159-97 Washer, Bellville (4) 4 Not Sold Separately Axle cover, left side 1 3644 Screw, #10-24 x 1/2 inch (4) 5 Not Sold Separately Axle cover, right side 2 Not Sold Separately Clamping bar (2) 3

Incoming search terms: