viva motor sports phantom

You search Auto repair manual PDF viva motor sports phantom, if there are search results will appear below. If search results do not exist, please search by others keyword.



  viva motor sports phantom Direct Download speed 5282 Kb/s

  viva motor sports phantom Full Version speed 6162 Kb/s



1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

Commonwealth of Massachusetts Registry of Motor Vehicles Motorcycle Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
DEFINITIONS MOTORCYCLE Any motor vehicle having a seat or saddle for the rider that is designed to travel with no more than three wheels contacting the ground, including any bicycle with a motor or driving wheels attached. MOTORIZED BICYCLE A pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty (30) miles per hour (mph) . OPERATION OF MOTORIZED BICYCLES Under Massachusetts law, mopeds fall into the category of “motorized bicycles”(with or without pedals) and are therefore regulated by the Registrar of Motor Vehicles. Individuals must have a valid learner’s permit or driver’s license to operate a motorized bicycle or moped. Mopeds must have automatic transmissions and cylinder capacities of no more than 50 cubic centimeters. In addition, mopeds must meet all federal motor vehicle safety standards and have maximum speeds of no more than 30 mph. The following limitations apply:  Individuals may not operate at speeds greater than 25 mph;  Individuals may not operate on state highways or limited- access roads with signs prohibiting bicycles;  Individuals may not operate on off-street recreational paths;  Individuals may use bicycle lanes along roadways;  Individuals must use the proper hand signals before stopping or turning;  Individuals and their passengers must wear United States Department of Transportation (US DOT) approved helmets when operating;  Individuals may not carry passengers while operating on a permit.

REKLUSE MOTOR SPORTS Pro Start Clutch Harley-Davidson OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 24-11-2010

download
REAK-IN PERIOD The ProStart clutch requires a short break-in period. During the break-in period, the ProStart should not be operated at steady engine speeds above 3000 RPMs for more than 10 minutes. Breaking-in the ProStart clutch equires start and stop cycles. Riding the ProStart clutch in stop-and-go city traffic for one hour will provide sufficient break-in. If you would like to accelerate the break-in period, find an empty parking lot with ample room and no other traffic. From a stop, bring the motorcycle to 20 miles per hour and then back to a stop. Repeat this process at least 20 times. MAINTENANCE Proper maintenance is important to ensure the longevity of the Rekluse ProStart clutch and the rest of the stock clutch components in your Harley- Davidson Motorcycle. Refer to your owner’s manual for proper primary chaincase oil levels and oil type. Rekluse recommends the use of Harley- Davidson Primary Chaincase lubricant with the Rekluse ProStart clutch. Do not use oils designed for use as automotive engine oil in your Primary Chaincase. If Harley-Davidson Primary Chaincase lubricant is not readily available, a premium-quality Diesel engine oil, such as Shell Rotella T, that does not contain friction modifiers may be substituted. Inspection and adjustment of the Rekluse ProStart clutch should only be performed by a service center trained in Harley-Davidson and Rekluse ProStart repair and maintenance. The Rekluse ProStart clutch should be inspected for adjustment after 1,000 miles of operation. Thereafter, inspection for adjustment should be performed at 5,000 mile intervals

Incoming search terms:

TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

BMW R1100RT, BMW R1150RT Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. These instructions start with the right side mirror. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 2. Once you have the mirror housing removed partially, twist and remove the light bulb from mirror housing. Remove mirror housing and set it on a cloth covered surface. 3. Remove the factory mirror by inserting a slotted screwdriver against each mirror mount snaps. Slowly twist and pry each snap until it releases from motor actuator. Repeat process until factory mirror disengages. NOTE: Insert the slotted screwdriver as close to each of the snaps as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. Connect the two mating connectors from the adapter Signal® mirror wire harness and the new Signal® mirror wire harness. Cut a slot in the foam disc to accommodate the anti-vibration prongs on the motor adapter. Place the foam disc onto the center of the Signal® mirror motor interface. Connect the Signal® mirror mating connector to the Signal® mirror wire harness. 5. Remove Cap Sheet from two-sided adhesive disc on back of Signal ® mirror. Align the anti-rotation prongs found on the top and bottom or left and right with the corresponding slots on the motor mount. Use the palm of your hand, push down on the Signal® mirror and the mirror housing until the Signal® mirror motor mount is fully engaged. Note: Push firmly on all sides of the Signal® mirror to ensure proper engagement and travel. Not doing so could result in mirror falling off. 6. Locate the light bulb and carefully disconnect the original light blue with black stripe wire [hot wire]. Connect the red wire from the Signal® mirror wire harness to the spade terminal on the light bulb. Connect the original light blue with black stripe wire to the other spade terminal located on the red wire of the Signal® mirror wire harness. Repeat the process for the original brown wire and the black wire from the Signal® mirror wire harness [ground wires]. Insert the light bulb back into the mirror housing. 7. Align the 3-pins with their corresponding snap holes and snap the mirror housing into place. 8. Insert key into the ignition and turn to the “ON” position. Activate the right hand turn indicator to verify that the new Signal® mirror is working correctly. Replace any other accessories necess

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

HONDA PHANTOM OWNER'S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
MOTORCYCLE SAFETY 1 Safe Riding Rules 2 Protective Apparel 2 Modifications 3 Loading and Accessories 6 PARTS LOCATION 9 Instruments and Indicators 11 MAJOR COMPONENTS (Information you need to operate this motorcycle) 11 Suspension 12 Brakes 16 Clutch 18 Fuel 22 Engine Oil 23 Tubeless Tyres 26 ESSENTIAL INDIVIDUAL MPONENTS 26 Ignition Switch 27 Right Handlebar Controls 28 Left Handlebar Controls FEATURES (Not required for operation) 29 Steering Lock 30 Helmet Holder 31 Side Cover 32 Document Compartment 33 Seat 34 Headlight Aim Vertical Adjustment 35 OPERATION 35 Pre-ride Inspection 36 Starting the Engine 39 Running-in 40 Riding 42 Braking 43 Parking 43 Anti-theft Tips MAINTENANCE 44 MAINTENANCE 45 Maintenance Schedule 48 Tool Kit 49 Serial Numbers 50 Maintenance Precautions 51 Air Cleaner 52 Crankcase Breather 53 Engine Oil 56 Spark Plugs 58 Throttle Operation 59 Idle Speed 60 Drive Chain 66 Front and Rear Suspension Inspection 66 Side Stand Page 67 Brake Pad Wear 69 Wheel Removal 74 Battery 77 Fuse Replacement 79 Stoplight Switch Adjustment 80 Bulb Replacement 84 CLEANING 86 STORAGE GUIDE 86 Storage 88 Removal From Storage 89 SPECIFICATIONS 92 CATALYTIC CONVERTER MOTORCYCLE SAFETY

VENTO PHANTOM R4i USERS MANUAL And Specifications

0

Filed Under (Vento) by admin on 02-11-2010

download
LEFT HAND CONTROLS Horn button – Press the switch to sound the horn Turn signal switch – Slide switch left when turning left, slide switch right when turning right and push in to cancel. Low beam / High beam Switch For High beam Turn upwards / For Low beam Turn downwards. Engine Kill Switch Turn into the X position to shut off. Turn into the O position to start the engine. RIGHT HAND CONTROLS Headlights / Running Lights – Slide switch towards the left up to first level and running lights will come on; slide once again to the next level the head lights will turn on. Electric Starter button – Press the electric starter button for a maximum of 5 seconds. NOTICE: If the engine does not start the first time, try again after 30 seconds. DO NOT use the electric starter after long periods of inactivity, doing so can drain the battery. IGNITION SWITCH 1. ON Position (Engine Ignition) Engine can be started Electrical devices such as horn, lights, etc. can be activated. Key cannot be removed. 2. OFF (Engine Shut-off) Engine cannot be started. Electrical devices such as horn, lights, etc. are inoperable Keys can be removed 3. LOCK Position Steering lock is engaged Engine cannot be started. Electrical devices such as horn, lights, etc. are inoperable Keys can be removed NOTES: Rotating the key switches the electrical circuitry ON and OFF WARNING: Do Not Turn the ignition key when the engine is running. Use the kill switch to shut-off, then rotate the key counter-clockwise towards the OFF position. NOTICE: If the engine is shut-off, please turn the ignition switch to the OFF or LOCK position. Failure to do so can cause battery drain or damage on the electrical system. STEERING LOCK OPERATION For your protection, activate the steering lock when leaving your vehicle parked or unattended. 1 . Turn handle bar to the left or right limit. 2 . Turn the key from OFF towards the LOCK position. 3. Remove the key. To unlock: Insert the key and rotate it to the OFF or ON position

Incoming search terms:

Incoming search terms: