vn800 rear suspension

You search Auto repair manual PDF vn800 rear suspension, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vn800 rear suspension Direct Download speed 5282 Kb/s

  vn800 rear suspension Full Version speed 6162 Kb/s



1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON LOW-PROFILE REAR TOURING SUSPENSION KIT Installation

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 2. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 3. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 4. Fasten the air pump, part number 54630-03A to the rear air-suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 5. Using the pressure-relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Failure to relieve air pressure from the rear suspension could cause injury during shock-absorber removal. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak on to the rear wheel, tire, and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 6. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air-hose fittings. NOTE Press the plastic collar down on the air-hose fitting to remove and install the air hose. 7. Remove the air hose fittings from the shock absorbers. Save the fittings for installation on the new shocks. NOTE Air-suspension shock absorbers are oil filled and must be kept upright at all times to prevent oil leakage. 8. Remove the lower mounting bolts and washers from the shock absorbers

Yamaha Rear Suspension Lowering Kit installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. This lowering method requires replacement rear suspension coupling components. This is a simple task, and is completely reversible. In addition, this kit provides for a 0″ setting, to easily return your bike to its original height. First, raise the rear tire off of the ground by the frame before you begin. Raise the motorcycle so no weight is applied to the rear wheel, allowing the rear wheel to spin freely. 2. Next, become familiar with your lowering kit. You’ll notice that there are two corners of the lowering component with two holes each, and one corner with a single hole. The corner with the single hole attaches to the swingarm (the bolt that is closest to the rear wheel). The only important part of this familiarization process, is to make sure that you get the part oriented in the correct position. The following photos will explain the purpose of the different holes, and also help you turn the part in the correct position before you install it. Look at the first photo on the next page: In the photo above, the part is positioned just as it should be, for installation on the left-hand side (kickstand side) of the motorcycle. A quick measurement will show that Dimension “A” on Side “A” should be shorter than Dimension “B” on Side “B”. If not, flip your part over (turn the face you are viewing away from you, but keep the corners with two holes on your left), and measure again. Next, study the photo below for info on the different heights you can set your bike to… When installed, Hole “0″ will place the bike at it’s original height. Placing the top bolt in Hole 1, and the bottom bolt in Hole 0, the bike will be lowered approximately ¾”. Placing the top bolt in Hole 1, and the bottom bolt in Hole 1, the bike will be lowered approximately 2″. Simple, eh? Now, let’s move on to installation. 3. Below is a photo of the factory suspension coupling as installed in your motorcycle. This photo was taken from the LH side of the bike, to keep things in perspective with our previous photos. Loosen the three bolts holding the original suspension coupling, and remove. Be aware that the rear wheel will drop down when the bolts are removed, just so there are no surprises!

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HARLEY DAVIDSON SPORTSTER LOW REAR SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION NOTE Internal shock absorber components are not repairable beyond the Service Parts listed on this instruction sheet. Consult your Harley-Davidson dealer if further service is required. The installation procedures for this kit are the same as the original equipment (OE) installation procedures in the Service Manual. Refer to the appropriate Service Manual for the rear suspension system removal and installation procedures. The OE hardware will be re-used in the kit installation. Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) SHOCK PRELOAD (SPRING) ADJUSTMENT Refer to the appropriate Service Manual for spring adjustment. Spanner wrench (94700-52L) is required for spring adjustment. SERVICE PARTS 1 is04854 Figure 1. Service Parts: Sportster Low Rear Suspension Kit Table 1. Service Parts: Sportster Low Rear Suspension Kit Part Number Description (Quantity) Item 54734-04 Rear shock (2)

HARLEY DAVIDSON TOURING LOW PROFILE REAR SUSPENSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the seat. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) 2. Disconnect the battery cables, negative cable first or remove the main fuse if equipped. 3. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 4. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 5. Fasten the air pump, part number 54630-03A to the rear air suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 6. Using the pressure relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 7. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air hose fittings

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

Honda Goldwing GL1800 Independent Rear Suspension Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm . 5.1 Explanation of OEM brake system and changes From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Trike Conversion Kit.

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

BMW Motorcycle R 1100 RS – Rear Frame

0

Filed Under (BMW) by admin on 16-11-2010

download
Complaint: On R 1100 RS models (above serial numbers only) with luggage racks, a crack may develop in the rear section of the frame (see drawing) if a load exceeding the permitted 11 lb. is applied to the luggage rack, or if a top case is used. Remedy: Please check all R 1100 RS models (in serial number range above) which pass through your workshops for cracks on the rear section of the frame. Cracked frames should be exchanged with the new part listed below. The new rear frame has been reinforced to use with larger loads. New Part: 46 51 2 320 698 (reinforced rear frame) Caution: Since the introduction of the rear luggage grid to accommodate the 33 liter removable top box, it is vital that this luggage grid and 33 liter top box not be installed on any of the above unless the reinforced rear frame is fitted, or a frame reinforcement kit is installed (a kit will be made available in the future to reinforce the rear frame of the above models, in order to install the 33 liter top box). The new reinforced rear frame (46 51 2 320 698) has been fitted since May 1995 production. Use of the new rear section of frame on an earlier production bike requires a new rear section of the dual seat as follows: Parts 52 53 2 325 121 Flash Green 52 53 2 325 122 Red Needed: 52 53 2 325 123 Black 52 53 2 325 120 Light Gray 52 53 2 325 211 Anthracite Warranty: Please explain to your customers that the top case can only be installed on bikes with reinforced rear frames. Claims for frame cracks which result from operation with large loads beyond specification will not be honored under the terms of the Limited Motorcycle Warranty.

Incoming search terms: