vstar tps

You search Auto repair manual PDF vstar tps, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vstar tps Direct Download speed 5282 Kb/s

  vstar tps Full Version speed 6162 Kb/s



Harley-Davidson Softail, Touring, Dyna, Sportster and V-Rod, SELF LEARNING MODULE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2012

download
STEP 1 – BATTERY CONNECTION Locate the battery and disconnect the negative battery cable. Mount the module in the open area in front of the battery with 2-tie straps or velcro straps, directing the harness from the module towards the 6 o’clock position. STEP 2 – THROTTLE POSITION SENSOR (TPS): Remove the air cleaner assembly and unplug the TPS sensor connector at the TPS sensor. The harness includes (2) TPS connectors which should be routed under the gas tank into the factory wire loom to the TPS sensor. The TPS sensor is located on the left side of the throttle body. Plug the (2) TPS connectors from the module in between the TPS sensor and to the factory TPS connector. STEP 3 – O2 SENSOR: Systems equipped with factory O2 sensors Rear: Unplug the Rear O2 sensor connector from the factory harness, which is located at the Rear exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors and connect one connector to the Rear O2 sensor and connect the other connector to the main factory O2 sensor connector. Front: Unplug the Front O2 sensor connector from the factory harness, which is located at the Front exhaust pipe. Route the module’s harness which includes (2) O2 sensor connectors, and connect one connector to the Front O2 sensor and connect the other connector to the main factory O2 sensor connector. Systems not equipped with factory O2 sensors NOTE: Many aftermarket exhaust systems are now equipped with plugged O2 sensor bungs which can be removed to accept an aftermarket O2 sensor. Typically these bungs already have a thread size of 18 mm x 1.5 mm. Exhaust systems not equipped with O2 sensor bungs need to have the supplied 18 mm x 1.5 mm thread size bung welded to the exhaust pipe in order to install an O2 sensor. The O2 sensor bung should be installed 3 to 6 inches away from the rear cylinder exhaust port and in front of the exhaust torque tube pipe area. The module prefers to receive information from the O2 sensor from an area that is NOT contaminated from atmospheric air. This air may enter through the tail pipe of an unrestricted or un-baffled exhaust pipe. The bung should not be installed in the “5 to 7 o’clock” area. If mounted in this area the O2 sensor can be damaged. The moisture from the gases exiting from the rear cylinder exhaust port will harm the ceramic shell element of the O2 sensor.

Incoming search terms:

1999-2001 Harley-Davidson Twin Cam 88 FI Controller Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Remove the seat. Remove or raise the fuel tank. The tank needs to be raised enough to give access to the fuel injectors and TPS wires. Unplug the front injector. On the FI Controller, there are 2 pairs of injector connectors. Plug the pair with the orange wires into the front cylinder injector harness and front cylinder injector. Repeat this using the other connector pair and the rear cylinder injector. Locate the TPS connector behind the throttle body. STEP 1 STEP3 STEP2 Installation Part# DFCH-2 2 Rear Cylinder Injector Front Cylinder Injector TPS Connector STEP 3 STEP 2 STEP1 Unplug the connector from the TPS. Crimp the wire tap onto the wire that is grey with a purple stripe. This wire should be in position “C” on the connector. Plug the grey wire from the FI Controller into the wire tap. Run the wiring harness for the FI Controller from the engine to the seat. Make sure that it will not get damaged when you reinstall the tank. Use one of the wire ties to tie the wires to the frame, away from the cylinder head. Place the FI Controller where you plan on mounting it permanently. In most cases, this will be under the seat. Connect the ground lug (black wire) to a grounding point on the bike. Use the Velcro tape to mount the FI Controller in position. Use alcohol swab to clean mounting surface prior to attaching Velcro. Reinstall fuel tank and seat. STEP 4 STEP 6 STEP 5 STEP4 STEP6 STEP5 Installation Part# DFCH-2 3 FI Controller
For Tech Support: 800.928.3962 Controls The FI Controller is preprogrammed with 4 base fuel curves. The curves are selected using the switch labeled BASE. These curves adjust fuel delivery based on throttle position and RPM, providing the right amount of fuel under all conditions. The 4 fuel curves correspond to varying levels of performance modifications. The levels of modification are broken down into the following groups. Base Curve 1 – Stock or basic modifications. This includes slip on exhausts, intakes, air boxes, and air filters. It will also work for headers or full exhaust systems. Base Curve 2 – Motor upgrades. This includes cams, 95 ci motors. Base Curve 3 – More extensive motor upgrades. This includes 103 ci motors, cams, ported heads

1997-1998 Harley-Davidson Evo FI controller installation manual

0

Filed Under (Harley Davidson) by admin on 25-03-2012

download
Remove the seat. Remove or raise the fuel tank. The tank needs to be raised enough to give access to the fuel injectors and TPS wires. Unplug the front injector. On the FI Controller, there are 2 pairs of injector connectors. Plug the pair with the orange wires into the front cylinder injector harness and front cylinder injector. Repeat this using the other connector pair and the rear cylinder injector. Locate the TPS connector behind the throttle body. STEP 1 STEP3 STEP2 Installation Part# DFCH-1 2 Rear Cylinder Injector Front Cylinder Injector TPS Connector STEP 3 STEP 2 STEP1 Unplug the connector from the TPS. Crimp the wire tap onto the wire that is grey with a purple stripe. This wire should be in position “C” on the connector. Plug the grey wire from the FI Controller into the wire tap. Run the wiring harness for the FI Controller from the engine to the seat. Make sure that it will not get damaged when you reinstall the tank. Use one of the wire ties to tie the wires to the frame, away from the cylinder head. Place the FI Controller where you plan on mounting it permanently. In most cases, this will be under the seat. Connect the ground lug (black wire) to a grounding point on the bike. Use the Velcro tape to mount the FI Controller in position. Use alcohol swab to clean mounting surface prior to attaching Velcro. Reinstall fuel tank and seat

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Installation Instructions S&S Billet Air Cleaner Kit for Victory Motorcycles

0

Filed Under (S&S) by admin on 29-10-2010

download
1 – Disconnect the negative battery cable from the motorcycle and route it away from any metal parts in the area. 2 – Remove the seat and gas tank from the Victory motorcycle following your Victory service manual for the specifi c model you are performing the work on. Picture 1 WARNING 3 Key Switch Cover and Coil Mounting Bracket Removal 1 – Remove the ignition key switch cover by pulling outward on it. Picture 2 illustrates the key switch cover. 2 – Remove the four socket head cap screws from the ignition and coil mounting bracket that holds the bracket to the front and rear heads. Picture 3 points out the location of the four socket head cap screws. 3 – With the bracket free from the front and rear head unplug the spark plug wires at the coil. 4 – Disconnect the coil and ignition switch at the connectors freeing them from the primary wiring harness. Idle Air Control Hoses and Throttle Position Sensor Removal 1 – Disconnect the Throttle Position Sensor (TPS) at the connector leaving the TPS attached to the throttle body. Picture 4 points out the TPS connector. 2 – Remove the Idle Air Control (IAC) supply hose from the air box. Note: Leave the 1.500″ rubber hose attached to the hard plastic IAC supply hose. Picture 4 points out the IAC air supply hose and the 1.500″ rubber hose. 3 – Remove the front Idle Air Control (IAC) air delivery hose from the rubber 90° fitting that leads into the front intake bore on the throttle body. Leave the 90° rubber fitting attached to the throttle body. Picture 4 points out the IAC front delivery hose. 4 – Remove the rear IAC air delivery hose from the rubber “T” fitting that leads into the rear intake bore on the throttle body. Leave the rubber “T” fitting attached to the throttle body. Picture 4 points out the IAC rear delivery hose

Harley-Davidson FLTR/ FLH/ FLHT/ FLHR EFI models 1995-2001 Variable Pressure Fuel Regulator Intallation manual

0

Filed Under (Harley Davidson) by admin on 27-04-2012

download
1 . Ensure vehicle runs correctly through all rpm ranges and idles correctly before attempting any work. It is highly recommended that a pressure / flow test be carried out before & after installation of the VariReg to determine fuel system condition . Stock HD 300 kPa / 44 psi, VariReg as delivered 360 kPa / 52 psi Note: In some countries gas stations do not “final filter” the fuel & therefore we recommend that the fuel filter canister be replaced every 15,000 klms (10,000 miles). Restriction of the fuel by way of a blocked or partially blocked filter will result in difficulty in tuning or failure to obtain satisfactory results during tuning. Should you experience difficulties in tuning, see Diagnosing fuel filter and pump faults 2. Remove air filter cover, air filter and backing plate. Check Throttle Position Sensor value at completely closed throttle as best performance will be obtained at the nominated settings. This will require backing off the idle screw and cold start idle actuator and screw adjustment as described in the workshop manual. The original T.P.S. values should be recorded for possible future reference. To set TPS values without the HD breakout box see VariReg TPS Setting for Harley-Davidsons The T.P.S. values must be set to 1995 – 1996 175 mV (+/- 25mV) 1997 – 2001 275 mV (+/- 25mV) Record the original TPS value here. ………………..mV YOU MUST ENSURE THROTTLE PLATES ARE COMPLETELY CLOSED AND NO BINDING EXISTS IN CABLES to obtain the correct value setting. 3. Reset idle screws to approximate previous settings, no need to start the engine. 4. Complete full or partial fuel tank removal as described in workshop manual. 5. Remove stock fuel pressure regulator as described in workshop manual and leave Horn removed from vehicle until after tuning, this will allow ease of access to the regulator

Victory Motorcycles Lloydz Motorworkz Billet Air Cleaner Kit Installation Instructions

0

Filed Under (Victory) by admin on 31-10-2010

download
1 – Disconnect the negative battery cable from the motorcycle and route it away from any metal parts in the area. 2 – Remove the seat and gas tank from the Victory® motorcycle following your Victory service manual for the specific model you are performing the work on. Key switch Cover and Coil Mounting Bracket Removal 1 – Remove the ignition key switch cover by pulling outward on it. picture 2 below illustrates the key switch cover. 2 – Remove the four socket head cap screws from the ignition and coil mounting bracket that holds the bracket to the front and rear heads. picture 3 below points out the location of the four socket head cap screws. 3 – With the bracket free from the front and rear head unplug the spark plug wires at the coil. 4 – Disconnect the coil and ignition switch at the connectors freeing them from the primary wiring harness. Idle Air Control Hoses and throttle position s ensor Removal 1 – Disconnect the Throttle Position Sensor (TPS) at the connector leaving the TPS attached to the throttle body. picture 4 next page points out the TPS connector. 2 – Remove the Idle Air Control (IAC) supply hose from the air box. Note: Leave the 1.500″ rubber hose attached to the hard plastic IAC supply hose. Picture 4 points out the IAC air supply hose and the 1.500″ rubber hose. 3 – Remove the front Idle Air Control (IAC) air delivery hose from the rubber 90° fitting that leads into the front intake bore on the throttle body. Leave the 90° rubber fitting attached to the throttle body. picture 4 points out the IAC front delivery hose. 4 – Remove the rear IAC air delivery hose from the rubber “T” fitting that leads into the rear intake bore on the throttle body. Leave the rubber “T” fitting attached to the throttle body. picture 4 points out the IAC rear delivery hose

1996 YAMAHA TDM 850 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
Model: TDM850 Model code: 4TX2 5AR1 (CH,A) Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,200 mm 790 mm 1,285 mm 805 mm 1,475 mm 165 mm 2,900 mm Radiator: Radiator capacity (including all routes) 1.7 L Tire: Type Size front rear Manufacturer front rear Type front rear Tubeless 110/80 ZR18 150/70 ZR17 BRIDGESTONE*/PIRELLI/MICHELIN BRIDGESTONE*/PIRELLI/MICHELIN BT54F/MTR03/MACADAM 90X BT54R/MTR04/MACADAM 90X *In Austria and Switzerland only Bridgestone tires are equipped on this mode. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO CARBURETION CARBURETOR FUEL LEVEL ADJUSTMENT 1. Measure: Fuel level a Fuel level: 15.8 16.8 mm (below the MIKUNI mark) Out of specification Adjust. Adjust the float level by slightly bending the float tang 1. Fuel level measurement and adjustment steps: Place the motorcycle on a level surface. Use a garage jack under the engine to ensure that the carburetors are positioned vertically. Connect the fuel level gauge 2 to the drain pipe. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO

Incoming search terms:

Yamaha Road Star Warrior Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and fuel tank. 2. Remove airbox and left airbox cover. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness under frame bracket towards airbox. (Fig 1) 4. Unplug stock black connector for fuel injectors. (Fig 2) 5. Plug Fuelpak 4-pin connectors in-line with the connectors from step 4. 6. Unplug the TPS connector and attach T-tap connector to the center wire (yellow). (Fig 3) 7. Route the Fuelpak violet wire to T-tap. (Fig 4) 8. Reattach the TPS connector. 9. Route black wire to the front of engine and down to the horn. (Fig 5) 10. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. 11. Route black and green wires to battery negative. 12. Attach Fuelpak to Fuelpak harness and mount under seat as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank. INSTALLATION INSTRUCTIONS FOR P/N 65005 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROAD STAR WARRIOR NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride.

Incoming search terms:

Incoming search terms: