vtx 1800 supercharger

You search Auto repair manual PDF vtx 1800 supercharger, if there are search results will appear below. If search results do not exist, please search by others keyword.

Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

Harley Davidson V-Rod SUPERCHARGER KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
Your Sprintex® Supercharger Installation can only be carried out by an Authorised Sprintex® Approved Supercharger Specialist. No unauthorised service or alteration may be undertaken to the Sprintex Supercharger kit or standard motorcycle Specification. Any modification or alterations from the Sprintex or Harley-Davidson specification shall affect your Warranty. 2. FUEL SPECIFICATIONS V ROD® Minimum 95RON Premium Unleaded Fuel 3. SUPERCHARGER BELT AND PULLEY Must be inspected at every routine service and the belt replaced when required. 4. OIL SPECIFICATION (ENGINE ONLY) Harley-Davidson Type Viscosity Harley-Davidson Rating Lowest Ambient Temperature Cold Weather Starts Below 50F (10C) HD Multigrade SAE10W40 HD360 Below 40°F (4°C) Excellent HD Multigrade SAE20W50 HD360 Above 40°F (4°C) Good 5. SPRINTEX V ROD SUPERCHARGER The Sprintex V Rod® Supercharger warranty provides a guarantee against any manufacturing defect during the warranty period, 12 months from the date of purchase or 20,000 Kms, whichever occurs first. The warranty guarantees the replacement of any parts of the Supercharger Installation which fail as a result of a manufacturing defect in normal operating conditions and excludes circuit racing, speed trials, drag racing and any form of motor sport activities. In addition, any unauthorised alteration to the motorcycles original specification or failure to meet the approved service requirements will affect your warranty. 6. EXCLUSIONS The following items will void your Sprintex Warranty: a. Alteration from standard specification b. Unauthorised Service or repair works c. Fitting of non Sprintex approved replacement parts d. Use of non standard air filter e. Installation by any non Approved Sprintex Agent

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

Honda VTX C 1800/ 1300 Backrest Kit Installation Manual

0

Filed Under (Honda) by admin on 04-01-2012

download
We highly recommend use of Loctite о on all nuts and bolts and check your hardware on regular basis. 1) Install the backrest bars with the pad. Do not tighten the bolts until the backrest is assembled with the brackets Install the brackets and backrest. The longer collars go to the front mounting holes. Do NOT tighten all the bolts until everything is assembled. We highly recommend red loc-tite о or any other compound will prevent bolts getting loose from vibration. Check bolts and metal parts periodically to make sure they are securely fastened