vulcan 1500 idle adjustmeny

You search Auto repair manual PDF vulcan 1500 idle adjustmeny, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vulcan 1500 idle adjustmeny Direct Download speed 5282 Kb/s

  vulcan 1500 idle adjustmeny Full Version speed 6162 Kb/s



Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

KAWASAKI VULCAN 1500, 1600, 2000 HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Lay a blanket folded several times over the fuel tank to protect it. 2. Loosen (do not remove) from underneath, the two hex nuts holding the risers to the upper triple clamp. (Steering head) 3. Remove the four handlebar clamp bolts. (8mm allen wrench) While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 4. Remove the nuts and risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Assemble the supplied lock washers and flat washers onto the supplied bolts. Install the new risers onto the triple clamp and finger-tighten the bolts. 5. Re-install the handlebars and upper clamp/gauge assembly. Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

Incoming search terms:

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

1999-2004 Kawasaki 1500 Drifter Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 Remove the seat. 2 Remove the left side cover. 3 Remove the speedometer assembly. 4 Unbolt the fuel tank. NOTE: It is not necessary to remove the fuel tank. It does however make the installation easier. If you do remove the tank, pay attention to the vent hose routing. Pressing the tabs on the black fuel line connector will allow the fuel line to be disconnected (Fig. A) 5 Remove the battery/ECU hold down bracket (Fig. B). 6 Unbolt and move the bank angle (tip over) sensor out of the way (Fig. C). Fig. A Fig. B Fig. C i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 2 Bank angle sensor (tip over switch) Remove these 2 bolts 7 Loosen the bolts holding the plastic tray on the left side of the bike (under the left side cover) (Fig. D). 8 Route the wire from the PCIII behind the plastic tray and under the frame side rail (Fig. E). 9 Retighten the bolts holding the plastic tray. 10 Continue routing the wires from the PCIII under the frame near the lower fuel tank mount and go up to the throttle body area (Fig. F). Fig. D Fig. E Fig F i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 3 Route PCIII harness between plastic tray and frame Route wires under frame Loosen these bolts 11 Disconnect the injector connector from the rear injector (Fig. H). 12 Plug the female PCIII connector with ORANGE/WHITE wire onto the rear injector (Fig. H). 13 Connect the male PCIII connector with ORANGE wire onto the stock injector connector (Fig. H). 14 Repeat steps 11 thru 13 for front injector using the PCIII connectors with the YELLOWcolored wires. 15 Locate the wires coming from the throttle position sensor. (Fig. H). The throttle position sensor is located on the right hand side of the throttle body. It is between the frame and engine

Incoming search terms:

S&S Super E and G Series "Shorty" Carburetors REMOVAL, Installation and Jetting Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
Remove Old Carburetor WARNINGS ● Gasoline is extremely flammable and explosive under certain conditions. Do not smoke around gasoline. Gasoline fumes are toxic when inhaled. Perform installation in a well ventilated area away from open flames or sparks. Any gasoline leak or spill constitutes a health and fire hazard. ● If motorcycle has been running, wait until engine and exhaust have cooled to avoid getting burned during installation. ● Electrical sparks can ignite explosive gasoline fumes. Failure to disconnect battery while working on motorcycle can also result in inadvertent engagement of starter and personal injury. A. Shut off fuel petcock and disconnect battery. B. Remove air cleaner assembly. Drain fuel from existing carburetor. Remove carburetor, manifold, choke cable and any carburetor mounting hardware NOTE – Removing and tightening hard to reach Allen bolts such as carb-manifold mounting bolts and V2 manifold flange bolts can be greatly simplified by the use of Allen ball-end drivers. These tools are available at most automotive and tool supply houses. See Picture 9. Additionally, Performance Plus of Evansville, Indiana, produces a hex wrench specially modified for accessibility of V 2 manifold bolts. Call 812-963-8854 for further information. As alternative, standard hex wrench can be shortened for convenience. NOTE – Some Buell motorcycles have a breather fitting with 90° elbow on rear head. Due to proximity of frame, elbow must be removed before fitting can be taken off engine. Loosen fitting and rotate to position convenient for cutting elbow. Secure fitting by tightening against cylinder head. Elbow may be inaccessible to hacksaw. In most instances, a die grinder with cutoff wheel will remove elbow with little difficulty. If die grinder is unavailable, grasp elbow firmly with pliers and snap off, then remove fitting. CAUTION – Extreme care must be taken to prevent metal chips from entering engine when elbow is removed. S&S recommends packing breather fitting with gease before removing elbow. Metal chips inside engine will cause extensive damage. Installer bears all responsibility for containment of chips and other debris. Picture 2 Picture 4 Picture 3
5 2. Prepare Air Cleaner Backplate NOTE – Fast idle lever screws, part #11-2384, must not be overtightened. Loctite or other thread locking compound may be used sparingly on threads to prevent screws from vibrating loose. CAUTION – Overtightening fast idle screws may damage backplate. A. All engines except V2s 1. Knuckles & Pans, 1936 to 1965 – Press plugs, part #50-8312, into holes in air cleaner backplate. See Picture 2 . 2. Shovels, 1966 to 1979, and Ironhead (IH) XLs, 1957 to 1979 – Press plug, part #50-8312, into hole in air cleaner backplate. See Picture 3 . 3. Shovels 1980 to 1984 and IH XLs 1980 to 1985 – Screw crankcase breather vent elbow fitting, part #50-8110, into hole in air cleaner backplate and angle downward as shown in Picture 4 . On 1983 and 1984 Shovels press plug, part #50-8312, into other hole on left. 4. Assemble fast idle mechanism as shown in Figure A . B. FL V2s 1984 to 1992 1. Press plug, part #50-8312, into hole on left in air cleaner backplate as shown in Picture 5 . 2. Screw vent hose elbow fitting, part #50-8110, into remaining hole at right. See Picture 5 . 3. Assemble fast idle mechanism as shown in Figure A . C. XL V2s 1986 to 1990 1. Press plug, part #50-8312, into hole on right in air cleaner backplate as shown in Picture 6 . 2. Screw vent hose nipple fitting, part #50-8111, into remaining hole at left. See Picture 6 . Elbow fitting, part #50-8110, supplied in kit may also be used in this location if required. 3. Assemble fast idle mechanism as shown in Figure A . D. FL V2s 1993 and up and XL V2s 1991 and up 1. Press plugs, part #50-8312, into both holes in air cleaner backplate as shown in Picture 7 . 2. Assemble fast idle mechanism as shown in Figure A . E. Buell motorcycles, 1994 and up 1. Assemble fast idle mechanism as shown in Figure A. 3. Throttle Preparation NOTE – Throttle grip assembly must be assembled correctly and work freely to prevent possible sticking during operation. Throttle must snap closed when released. Cable routing must be free of tight bends to minimize friction between cable and housing

Incoming search terms: