what carburetor do yamaha ttr 230 2007 use

You search Auto repair manual PDF what carburetor do yamaha ttr 230 2007 use, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what carburetor do yamaha ttr 230 2007 use Direct Download speed 5282 Kb/s

  what carburetor do yamaha ttr 230 2007 use Full Version speed 6162 Kb/s



KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

Incoming search terms:

HSR Carburetor Total Kits Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
Intake Manifold: 1. Install MAP sensor in Mikuni manifold (Twin Cam only). 2. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 3. Attach the rubber flange to the Mikuni manifold with the furnished 5/16″x3/4″ bolts and washers. Choke Cables: Mikuni & Harley-Davidson Route the cable with largest radius bends possible. Check the cable for free-play after installation. If there is no free-play, the engine may run rich and deliver poor performance or low fuel mileage. Harley Cable (Twin Cam Kits: 42-19, 45-4) : 1. Remove the Harley choke cable from the stock carb. 2. Remove the spring and plunger from the cable. 3. Remove the spring and plunger from the Mikuni. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut (See Figure 1). Total Kit Installation Instructions The HSR series carburetors are precise yet durable instruments; however, like any other piece of fine equipment, they require correct installation and reasonable care to assure optimum performance and long life. Extra time spent during installation will pay off in both short and long term performance and reliability. This Mikuni HSR carburetor kit is designed to be a bolt-on application, and as such, is set-up and jetted properly for most applications. However, since Harley-Davidson motors are often highly modified, alternate tuning settings may be required. The Mikuni Tuning Manual helps make jetting alterations and adjustments an easy matter. NOTE: Carburetor Kits not designated as C.A.R.B. exempt, are not legal for motor vehicles operated on public highways in the state of California, or in any other states and countries where similar laws apply. WARNING NOTE: NOTE: WARNING CAUTION NOTE: NOTE: TK-2 6. Install the new assembly into the Mikuni carburetor. Be careful to only gently tighten the plastic nut. 7. Loosen the knurled plastic friction nut behind the choke knob and check for free-play (see Figure 2). Figure 1: Harley nut with Mikuni spring & plunger Figure 2: Choke cable adjustments Mikuni Cable (Evo Kits: 42-8, 45-2 & 45-3) : 1. Remove nut, spring and plunger from the Mikuni. 2. Install the nut, spring and plunger onto the cable. 3. Install the assembly into the Mikuni HSR carburetor. Be careful to only gently tighten the plastic nut. 4. Check for free-play. Adjust the cable as necessary. An optional choke cable mounting bracket is included in the Evo kits for custom installations. Carburetor Installation: 1. Insert the carb fully into the rubber flange, align with engine and tighten the clamp. 2. Slip the fuel hose onto the carburetor’s fuel fitting and secure with the enclosed hose clamp. NOTE: Some Twin Cam installations may require removal of a small amount of fin material from the cylinders to clear the float bowl. Throttle Cables The HSR carburetor uses stock 1990 and later Harley- Davidson cables. However, if your Harley is fitted with some other carburetor, you may need to purchase a set of cables. See your dealer for the correct cable set. 1. Route the throttle cables with large radius curves and so they do not interfere with other components. 2. Screw the cable adjusters together to make them as short as possible. 3. Connect the “close” cable first (see Figure 3). 4. Install the “open” cable next (see Figure 3). 5. Adjust the opening cable until the slide can be opened fully. Snug the adjuster lock nut. 6. Turn the handlebar to the right and adjust the throttle free-play with the closing cable adjuster to approximately 1/8″ (see Figure 4)

Incoming search terms:

YAMAHA RAPTOR 350 Removing stock carburetor and cables

0

Filed Under (Yamaha) by admin on 18-01-2012

download
remove seat and gas tank. Make sure fuel petcock is in “off” position. 2. Remove throttle cable paying close attention to routing, as the new cable (s) will need too be routed the same. 3. Remove stock carburetor and stock throttle housing. Stuff a clean, dry rag into manifold to keep debris out of motor. 4. Remove stock air box. 5. Remove choke cable from handlebars. 6. Remove carb vent line from bike. Carburetor installation 1. Carefully trim the rubber alignment tab off of the face of the manifold with a razor blade or side cutters. 2. Remove the hex pipe plug from the carb cap using a 11mm or 7/16 wrench. Do not discard plug, as it will be needed later. Install the metering adjustment tool included in the hardware kit. Do not over-tighten as damage may occur to cap. 3. Attach fuel line to carburetor and secure with clamp. 4. Install remote idle cable into tab on top of carburetor. See main manual for this step. NOTE: Nut must be removed from cable before installation 5. Place carburetor into manifold

Incoming search terms:

HSR Carburetor Total Kits Installation And Tuning Manual

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Disconnect the battery ground wire from the battery. 2. Turn the fuel petcock to the “OFF” position. 3. Elevate the rear of the fuel tank for better access to the carburetor area. 4. Remove the coil, horn or other devices on the left hand side of the engine to allow free access to the intake manifold bolts. 5. Remove the complete air cleaner assembly, including the backing plate. 6. Disconnect any vacuum hoses and the fuel hose from the stock carburetor. 7. Disconnect the choke cable from the frame. 8. Remove the stock carburetor. 9. Evo: remove the stock manifold. 10. Twin Cam: unplug MAP sensor, remove manifold and then remove the MAP sensor from the manifold. Installation: Intake Manifold: Twin Cam only: Install MAP sensor in Mikuni manifold. 1. Attach the Mikuni manifold to the engine. Align the manifold before tightening the bolts. The flange surface of the Mikuni manifold should be parallel with the front of the engine’s cam cover. Use a level or angle meter to check this. Tighten the manifold bolts. 2. Attach the rubber flange to the Mikuni manifold with the 5/16″x3/4″ bolts and washers. To ease installation, use liqiud detergent to lubricate the manifold seals. Choke: Evo: We recommend that you use the Mikuni choke cable that is furnished with the carburetor. However, you can use the stock Harley cable (’90-’99 models only) if you follow the Twin Cam choke cable instructions. Twin Cam: 1. Remove the Harley choke cable from the stock carb. 2. Remove the Harley spring and plunger from the Harley choke cable. 3. Remove the Mikuni spring and plunger from the Mikuni carburetor. 5. Install the Mikuni spring and plunger onto the Harley choke cable. Change nothing else; be sure to use the Harley plastic nut, not the Mikuni nut. 6. Install the new assembly into the Mikuni. Be careful to only gently tighten the plastic nut.

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Adjusting the Pekar K68 for Dnepr or Ural

0

Filed Under (Tips and Review) by admin on 11-11-2010

download
1. Make sure the ignition timing is correct 2. Adjust the valves as necessary to ensure proper operation 3. Run the engine to warm it up a bit 4. Adjust the float setting. To do this, remove the carburetors (leave the throttle cables attached), remove the bowl and turn the carburetor upside down (fuel will spill). The float should look like this: Adjust as necessary by bending the float support (#37 in Figure 1). Reinstall Installation and idle adjustment 1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns. * Starting using the K68′s (cold weather) 1. Verify fuel flow. Apply choke (pull 52 in Fig1). 2. Using the ticklers (13) allow fuel to enter the bowl until fuel drains from (14) 3. With the ignition off, kick 1 or 2 times 4. Turn ignition on, and as soon as engine is warmed up (maybe sooner) push choke mechanisms to open choke Idle Adjustment (engine running and warm) 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

Ural carburetors Installation and idle adjustment

0

Filed Under (Ural) by admin on 02-11-2010

download
1. First you must adjust the idle. It is acceptable per the manual to adjust the idle by using the idle adjust screws (11). This usually involves screwing them then backing out 1 to 1.5 turns. Or you can adjust looking at the sliders 2. If installing the carburetors: a. Remove the cover (2) b. Reomve the slider (3) c. Place the throttle cable through the guide (18) with the spring (4) on the cable. d. Route the cable through the slide catch (6) e. Insert the slide assembly into the chamber and make sure it easily slides up and down. Direct the needle (8) into the opening of the diffuser (angled side visible). f. Screw assembly together and verify via throttle movement that slide moves freely. Attach fuel delivery lines to (12). 3. Using the idle set screw (11) raise the slider so the lower edge is 1-2 mm. 4. Assemble to engine using the proper gaskets (paper – felt – paper). 5. Using the locknut (26) adjust the free play of the throttle cable (2-3 mm) 6. Adjust the idle mixture screw – turn in completely then out 1 to 1.5 turns 1. Remove one of the spark plug caps, and with the cap shorted, adjust (11) to decrease RPM’s to a point of being minimally steady. 2. Adjust the mixture (15) out until RPM’s decrease. Turn in until RPM’s increase slightly. Then turn in screws ¼ to 1/3 revoultion. 3. Do the same for the second carburetor with the first spark plug cap shorted. 4. With both cylinders, adjust each idle (11) on each carburetor the same amount each until it’s at a steady, minimal RPM. Use small changes. (at this point you can use your airflow tool to check). 5. Sharply increase, then decrease throttle. Then engine must return to low RPMs smoothly. If the engine goes below limits, readjust (11) from step 4. Synchronization of the K68 Note: Rather than using the opposite cylinder shorted to test the pull of the live cylinder carburetor, you can use something like a Twinmax connected to the test ports (27 Fig 1). Or, if you have a model without these ports, use a Synchrometer (Appendix 2) held against the face of the carburetor. These tools merely show airflow passing through each carburetor (which is dependent on the position and wear on the slide). If using these tools, it’s not necessary to do the following steps. You wil want to use a throttle guide (Appendix 1), to show airflow at various throttle settings. Using the flow meter of your choice make sure each carburetor is the same at the various throttle settings. 1. Place the motorcycle on the center stand ensuring the rear wheel is suspended 2. Make sure you have large area to work with (safety issues here) 3. Shift into the highest gear with the engine running 4. Short one spark plug cap to the cylinder (using a nail or something in the fins) 5. Increase the speed to 40-50 km/hr 6. Fix the throttle using the throttle (maybe using a throttle stop screw under the throttle housing). 7. Reconnect other cylinder and using the opposite carburetor determine the speed which should be the same as the first. 8. Adjust the position of this slide to achieve the referenced speed using the locknut at the top of the carburetor.

Incoming search terms:

YAMAHA YZF-R125 SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Fuel tank cap To remove the fuel tank cap 1. Open the fuel tank cap lock cover. 2. Insert the key into the lock and turn it 1/4 turn counterclockwise. The lock will be released and the fuel tank cap can be removed. To install the fuel tank cap 1. Push the fuel tank cap into position with the key inserted in the lock. 2. Turn the key clockwise to the original position, and then remove it. 3. Close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked. WARNING EWA11140 Make sure that the fuel tank cap is properly installed before riding. EAU13211 Fuel Make sure that there is sufficient fuel in the tank. Fill the fuel tank to the bottom of the filler tube as shown. WARNING EWA10880 Do not overfill the fuel tank, otherwise it may overflow when the fuel warms up and expands. Avoid spilling fuel on the hot en- gine. 1. Fuel tank cap lock cover 2. Unlock. 1. Fuel tank filler tube 2. Fuel level
INSTRUMENT AND CONTROL FUNCTIONS 3-8 3 CAUTION: ECA10070 Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EAU43420 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system. Your Yamaha engine has been designed to use premium unleaded gasoline with a research octane number of 95 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. EAU13442 Catalytic converters This vehicle is equipped with catalytic converters in the exhaust system. WARNING EWA10860 The exhaust system is hot after operation. Make sure that the exhaust system has cooled down before doing any maintenance work. CAUTION: ECA10700 The following precautions must be observed to prevent a fire hazard or other damages. Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter. Never park the vehicle near possible fire hazards such as grass or other materials that easily burn. Do not allow the engine to idle too long.

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HOVELHEAD & IRONHEADXL 42mm Mikuni Carburetor And Manifold Kit INSTALLATION Instructions

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
THROTTLE CABLE ADJUSTMENT A) Rotate the throttle grip to the full open position, look into the throttle bore and see if the throttle valve (slide) opens completely. If the throttle valve does not open completely unscrew the adjuster on the opening cable until it does. This adjustment should be made carefully to assure maximum carburetor performance. After adjustment tighten the adjuster jam nut. B) After adjusting the open cable, adjust throttle freeplay with the closing (idle) cable to approximately 1/8″ an indicated in the following illustration. note It is very important to adjust the cables in the preceding described manner to ensure that the idle cable operates correctly for safety. It must close the throttle completely 2 PLEASE NOTE USE CAUTION PLEASE NOTE SAFETY WARNING pull open cable pull close cable SHOVELHEAD/IRONHEAD XL Installation Instructions Check and make sure that the throttle cables are routed properly by rechecking the throttle play as the handlebars are turned from side-to-side; the amount play should remain consistent. C) After the throttle cables have been adjusted, make sure that all the lock nuts are securely tightened. 5. AIR CLEANER A) The air filter bracket is attached to the crankcase with 1 long bolt, and a bracket-spacer. Removed the crankcase nut located between the tappet blocks & replace it with the enclosed bracket spacer; tighten the spacer securely. B) Remove the stud protectors from the K&N filter and place the two backing plates on the studs. Now slip the the filter onto the carburetor. C) Attach the 2 long brackets to the air filter studs with the enclosed nuts & flat washers, and to the bracket spacer with the enclosed bolt using the lock washers, and flat washers. When the carburetor and air cleaner are properly aligned, securely tighten all of the mounting hardware including the intake manifold clamps. In some cases it may be necessary to bend the brackets slightly to arrive at the correct fit. D) Use the enclosed hose clamps to secure the fuel hose to the petcock, and the HSR carburetor. The screw clamp goes on the petcock end and the spring clamp attaches to the carburetor end. E) Attach the chrome air filter cover with the enclosed socket head screw. 7. CHOKE CABLE INSTALLATION A) Attach the Mikuni choke cable bracket to the original choke cable bracket on the air cleaner stud with the enclose hardware as illustrated

Incoming search terms: