what is the torque spec on a dyna rear axle

You search Auto repair manual PDF what is the torque spec on a dyna rear axle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what is the torque spec on a dyna rear axle Direct Download speed 5282 Kb/s

  what is the torque spec on a dyna rear axle Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL CHROME REAR AXLE ADJUSTER AND COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Block the motorcycle underneath the frame so the weight of the vehicle is off of the rear wheel, but do not raise the rear wheel off the ground. 2. Some models require loosening or removal of the muffler or mufflers in order to remove the rear axle. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. Remove the saddlebags if desired for extra working clearance. See SADDLEBAG REMOVAL in the Service Manual. 3. See Figure 1. Remove the original axle adjustment bolts (1) and jam nuts (2) from both sides of the motorcycle and discard. NOTE On a bike that has been previously serviced, ensure that the axle has not been removed and re-installed from the left side (with the castle nut to the right of the wheel). If it has, the axle MUST be inserted from the right side of the motorcycle. 4. Remove the retaining pin (7), castle nut (5) and washer (4) from the left side of the axle (6). Discard the washer, but save the pin and nut for later re-assembly. 5 7 1 4 6 2 3 is04101 1. Axle adjust bolt 2. Jam nut 3. Axle adjuster collar 4. Washer 5. Castle nut 6. Rear axle 7. Retaining pin Figure 1. Rear Axle Hardware (Left Side Shown) 5. Tap the axle toward the right side of the motorcycle and remove. The belt adjuster collars (3) will fall loose as the axle is removed. The collars can be discarded. The wheel bearing spacers may also fall loose or be dislodged. Be sure to return these to their original position on the vehicle (short spacer on the right side, long spacer on the left). 6. Inspect axle components for damage or excessive wear, and replace as required

Incoming search terms:

HARLEY DAVIDSON SOFTAIL REAR AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. 1988-1999 FLSTF Models: Remove rear muffler heat shield, loosen rear exhaust Torca clamp, then remove rear muffler from support following the instructions in the appropriate Service Manual. 2000 and Later Models: Remove exhaust system following the instructions in the appropriate Service Manual. NOTE In some cases, if bike has been previously serviced, the axle may have been removed and re-installed from the left side (with castle nut and cotter pin on the right). If this is the case, the axle must be removed and installed from the the right. If axle appears as original configuration (as in Figure 1), it is not necessary to loosen the rear axle nut or remove the cotter pin (or spring clip) from the rear castle nut. 2. All Models: See Figure 1. On the left side of the motorcycle, loosen the axle adjuster screw (1) and jamnut (2) just enough to be able to remove the jamnut. 3. 1988-1999 FLSTF Models Only: See Figure 2. On the right side (brake caliper side), use a T40 TORX drive to remove the two pin bolts from caliper. Remove caliper by gently rocking caliper back and forth to compress caliper piston, then carefully slide caliper off brake disc. Use cable strap or other suitable means to support caliper. 4. All Models: On the right side, loosen the axle adjuster screw and jamnut just enough to be able to remove the jamnut. 5. All Models: See Figure 3. On each side, place retainer clip (oriented as shown) and washer from kit over axle adjuster screw and replace jamnut. Turn in axle adjuster screw until it is in its original position against axle spacer, but leave jamnut loose. 1 2 4 3 is04788 1. Axle adjuster screw 2. Jamnut 3. Castle nut 4. Cotter pin (or spring clip) Figure 1. Rear Axle Hardware

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

HARLEY DAVIDSON DYNA REAR AXLE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Models This kit fits 2006 Dyna models. This kit does not fit on motorcycles equipped with saddlebags. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Place axle covers in position over ends of swingarm with the deeper cover on the left side (covering the axle nut). 2. Fasten the clamping bars (3) to the backs of the covers using hex-head screws (5) and Belleville washers (4), securing the covers to the swingarm. Tighten the hex-head screws to 21-27 in-lbs (2.4-3.0 Nm) . Do not overtighten SERVICE PARTS 4 1 3 4 5 2 3 5 is00709 Figure 1. Service Parts: Dyna Swingarm Axle Cover Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 45159-97 Washer, Bellville (4) 4 Not Sold Separately Axle cover, left side 1 3644 Screw, #10-24 x 1/2 inch (4) 5 Not Sold Separately Axle cover, right side 2 Not Sold Separately Clamping bar (2) 3

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

HARLEY DAVIDSON DYNA REAR STOP/ TAIL/ TURN SIGNAL RELOCATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
PREPARATION NOTE Position the motorcycle upright using a suitable lift or jack. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow instructions to remove the main fuse. 2. Follow the service manual instructions to remove the seat. 3. Raise the rear of the vehicle to allow access to the underside of the rear fender. LICENSE BRACKET AND ILLUMINATOR REMOVAL For Models WITHOUT a Center Tail Lamp NOTE See Figure 1. The reflector mounting block (2) is held to the fender (1) with double sided tape. Remove with care to avoid scratching paint. 1 3 2 5 4 6 7 is06256 1. Rear fender 2. Rear reflector and mounting block 3. Wire channel (2) 4. License plate bracket mount 5.5/16-18 screw (2) 6. License plate illuminator 7. M4 screw (2) Figure 1. Rear Fender, Models Without Center Tail Lamp 1. Remove the rear reflector and mounting block (2) from the underside of the rear fender (1). 2. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. NOTE Before removing rear wiring, note wire routing. -J04856 1 of 10 3. Remove the rear lamp wiring from behind the wire channels (3) on the underside of the fender. 4. Disconnect the two-way license lamp connector [93] and the four-way right [18] and left [19] stop/tail/turn (STT) lamp connectors from the STT module in the area under the seat. 5. Remove the two 5/16-18 screws (5) retaining the license plate bracket mount assembly (4) to the fender support. 6. Remove the license plate illuminator (6) from the license plate bracket mount assembly. Save the illuminator. The bracket mount (4) and four screws (5, 7) can be discarded. 7. Proceed to License Bracket and Illuminator Assembly . For Models WITH a Center Tail Lamp NOTE On these models, the license plate illuminator is part of the center tail lamp and is not removed. 1. Remove the three screws retaining the license plate bracket to the tail lamp housing. Remove the bracket and set aside for later assembly. 2. Proceed to Rear Lamp Wiring, For Models WITH a Center Tail Lamp and RED Stop/Turn Signals or AMBER Turn Signals . LICENSE BRACKET AND ILLUMINATOR ASSEMBLY For Models WITHOUT a Center Tail Lamp 1. See Figure 7. Get the new license plate bracket (3), illuminator cover (4), spacer (6) and two M4 screws (5) from the kit, and the license plate illuminator (A) removed from the original equipment (OE) license plate bracket. 2. See Figure 2. Assemble the illuminator (1), spacer (2) and cover (3) to the license plate bracket (5) in the sequence shown, and tighten the screws (4) securely. 3. Get the STT relocation weldment (6), two screws (7) and two flat washers (8) from the kit. 4. Apply a few drops of Loctite 271 – Red to the clean screw threads. Assemble the license plate bracket to the weldment as shown, and tighten the screws to 120 in-lbs (13.6 N-m) . NOTE If using a metal tool to install the black nuts, protect the finish with cloth or paper to prevent damage. 5. Loosely install the black painted nuts (9) onto the threaded studs on each side of the STT relocation weldment. 6. Remove the wires and socket terminals from the two-way license plate illuminator socket housing. Set the socket housing aside for later installation

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

Incoming search terms: