what jetting for 2008 kawasaki teryx

You search Auto repair manual PDF what jetting for 2008 kawasaki teryx, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what jetting for 2008 kawasaki teryx Direct Download speed 5282 Kb/s

  what jetting for 2008 kawasaki teryx Full Version speed 6162 Kb/s



2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Upgrading the Suspension on the Kawasaki ER6-F/ N

0

Filed Under (Kawasaki) by admin on 30-11-2010

download
Top fork is as removed. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Before removing the fork from the clamps on the yokes I loosened the fork top. Before removing the fork top the fork-slider was placed in a vice and the bottom bolt loosened….. … before finally being removed with the fork upside down. Because the springs were still in situ this gave sufficient tension on the damper-rod to prevent it from turning and allow the bolt to be removed. When I turned the fork the right-way up to remove the fork-top I did it over a container to catch the oil. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource All the OE components that will no longer be required. Left to right. Fork-top, spacer tube, washer, spring, damper-rod. Bottom bolts get re-used. Old and new, laid-out for comparison. The damper unit, minus spring and fork-top, drops inside the stanchion and slider. Kawasaki Ninja 650R (ER-6F) & ER-6N Resource Then the bolt goes back in, as tight as possible, to secure it. Top fork is done, second one awaits. Note the spring seat on the right, just below the spring. This drops over the damping rod after the oil has been added. The small locking-nut screws over the threaded part of the damping-rod next, all the way to the bottom. Spring drops in and then the fork-top screws on to the damping-rod as well, all the way down to the lock-nut which is used to secure it. At this point the stanchion is extended to the fork-top which is screwed in. Job done.

Incoming search terms:

Kawasaki Teryx Skid Plate Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Let skid sit in sun or inside house at room temperature for a couple hours. Cold weather can shrink plastic slightly but this is not an issue once installed. 2. Remove Stock Teryx Hardware/skids and set aside hardware to use on new skid 3. You have a couple options in mounting the new skids. 1) remove stock metal engine inspection cover underneath Teryx, or 2) using UHMW skid as template cut out hole in inspection cover (A below) to allow access to oil filter. Cut hole substantially larger than skid hole so as not to cut yourself when removing/installing oil filter 5. Fasten all main skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. 6. Fasten all front and rear skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. . Once skids are in desired location tighten all bolts 9. You will be required to drill 2 – 3/16 pilot holes in the 2 rear most main skid mounting locations. Use the supplied self tapping bolts and washers to attach skid in these locations

KAWASAKI TERYX POWERFLOW INSTALLATION PROCEDURE

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the airbox and clean thoroughly. 2. Cut off the factory plastic ring on airbox. DO NOT cut a bigger than 3″ 5/8 diameter (See figure #1) 3. After cutting hole in airbox place billet adapter inside the airbox and insert hole then mark the mounting holes for the billet adapter. 4. Drill the marked locations with a 7/32 drill bit. 2. Install the billet adapter from the inside of the airbox with the Trinity Racing logo at the top of the airbox. Insert the bolts and washers from the carburetor side of the airbox and then secure it with blue loctite then tighten bolts. 3. Install Outerwear over new filter. 5. Install the filter onto the billet adapter and make sure the rubber neck of the air filter is completely free of oil. Tighten the filter clamp securely, but do not over tighten and cut into the rubber neck of the filter. 6. Reinstall the air box assemble with lid ( if you choose to reinstall the airbox lid ) onto the vehicle. Be sure to tighten and double-check all the nuts and bolts you have installed. 7. Check your vehicles jetting. Depending on your modifications and riding altitude, a jetting change may be required for your ATV to run properly.

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Incoming search terms:

Kawasaki Teryx Bowkaddy Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The most effective method of mounting Bowkaddy on a Kawasaki Teryx is with the use of Kaddy Bracket UTV. However, one small after-market modification is necessary to make the bracket fit the rear roll bars on these side by side vehicles. Two additional 21/64″ holes must be drilled in the bracket at the locations shown in the image below. For more product and installation information,

Kawasaki Teryx Electric Steering Installation Manual

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
installation Instructions for Kawasaki Teryx 1. Before installation, center steering wheel and verify tires are straight. 2. Begin by removing all Phillips screws retaining the plastic hood to the front grill, headlights, and frame structure and remove front clip assembly. 3. Remove plastic shroud by removing the 4 phillips screws that retain it to the frame. 4. There are 2 bolts that hold the steering column tube in place and you need to reach up under frame work to get to them. They are 14 mm and you need a box and open end wrench to access them. Loosen the upper one and remove the lower one. Remove the pinch bolt at the column shaft and u-joint. Remove the lower pinch bolt at the rack and u-joint and while tilting the column up and down remove the stock steering shaft.
5. Once the shaft is removed, you are ready for installation. Your bracket and motor has come completely assembled as shown below. You will need to remove the lower shaft from the motor to install it. After removal of the shaft you will need to loosen the 3 mounting bolts from the bracket to the motor to allow clearance for the bracket to slide over the frame piece where it will mount

2008 KAWASAKI KX 250 F RACING AND EVOLUTION EXHAUST SYSTEM

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
the Akrapovic Racing and Evolution complete exhaust systems are the flagships of our product lines. They are designed for competition-oriented MX riders who demand maximum performance from their exhaust systems. With their production quality, engine performance improvements and modern Hexagonal muffler design they satisfy the requirements of all riders. The systems are designed for two markets; in the US they are available with an approved spark arrester, and for the EU and other non-US markets they come with a noise damper. New for 2008 is additional chamber that helps to reduce noise emission and provides better power and torque at low rpm range. PERFORMANCE Measurements of the Akrapovic EVOLUTION system on the KAWASAKI KX 250 F (with muffler insert): Power & Torque: The Akrapovic Evolution and Racing systems deliver a performance increase throughout nearly the entire rpm range. It is most pronounced in the bottom and the top of the range. The systems deliver increased torque similar to the power increase. Max. increased power of 0.7 HP was measured at 12260 rpm, while max. power of 34.6 HP was measured at 11400 rpm. CONFIGURATION Akrapovic Racing and Evolution systems are of a recognised Hexagonal off-road form. They differ only in terms of the material of the pipe: we use stainless steel for Racing and titanium for Evolution. The header tube is conical, made from stainless steel (Racing) or titanium (Evolution) with additional chamber. It is jointed with a conical SS/titanium link pipe by a sleeve joint, which is secured with a silicon-shielded spring. The link pipe is welded to the muffler. The inlet cap, due to the method of connection with the link pipe, is made from stainless steel (Racing) or titanium (Evolution), same for the internal perforation. The outlet cap is made of carbon-fiber for evolution and composite polymer for Racing system. The outer sleeve of the muffler is available either made from titanium or carbon fiber. The system is attached to the motorcycle with the Akrapovic carbon fiber clamp. The Akrapovic carbon fiber heat shield is also intended for this system. The system comes with a built-in noise damper for the European and other markets, and an approved spark arrester for the American market, which is marked with a laser engraving