what makes sparks come out from my piaggio ciao contact set

You search Auto repair manual PDF what makes sparks come out from my piaggio ciao contact set, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what makes sparks come out from my piaggio ciao contact set Direct Download speed 5282 Kb/s

  what makes sparks come out from my piaggio ciao contact set Full Version speed 6162 Kb/s



HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON STREET SLAMMER HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
This kit does not fit models equipped with Hydraulic Clutch Kits, handlebar mounted gauges or the Road Tech® Radio or FLHRS models equipped with an accessory windshield. REMOVAL Preparation – All Models To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Save the seat hardware for installation. -J04406 When servicing the fuel system, do not smoke or allo w open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Softail and Dyna models: See the service manual and loosen the fuel tank. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled DOT 4 brake fluid. 3. See the service manual and drain the brake fluid from the front brake reservoir and brake lines. Handlebar Removal – Dyna and Softail NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Note the front brake line routing and the orientation of the banjo fittings. See the service manual and disconnect and remove the brake line. Save the banjo bolts, but discard the brake line gaskets. 2. Remove the plastic wiring retainer clips that secure the turn signal harnesses to the handlebar, if equipped. 3. Remove the front brake master cylinder and clutch lever assemblies from the handlebar.

HONDA 450E/ S MOUNTING AND ARS ADJUSTMENT INSTALLATION

0

Filed Under (Honda) by admin on 24-12-2011

download
MULTI-RATE SPRINGS AND THE ARS SYSTEM Depending on the application dual–rate springs are fitted on the shocks. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other off road hazards. ARS stands for Adjustable Rate Suspension. ARS is available on some dual-rate spring 4-wheel ATV shocks. ARS differs from spring preload. The ARS system allows the rider to increase or decrease the load-carrying capacity of the shocks by turning a lever. Depending on the application and spring set, the rider can increase the load capacity of the shocks up to 50 percent. The average preloader that makes a half-inch increase in preload will HONDA 450E/S MOUNTING & ARS ADJUSTMENT INSTRUCTIONS Continued on next page. #TRX450 – 5/28/99 #TRX450 – 5/28/99 Fig. 1. Front shock installation. Note that the shock body is at the top with the shaft pointing down. ARS shown is in the unloaded position. Fig. 2. Rear shock mounting with ARS. Position the lever so that it will not come in contact with any vehicle parts around it. The cup can be rotated to reposition the lever if necessary.
increase the capacity of the shocks to only about 5 to 10 percent. ARS allows the shocks to be correct for solo riding, but still handle the increased weight of an added load. ARS can also be employed to stiffen the rates for aggressive riding. The ARS system consists of an indexing lever and a stepped cup that contains the short spring of the dual- rate. The position of the lever in relation to the steps in the cup determines how long the spring set remains on the soft, or initial, spring rate. On most ARS applications, four positions can be selected from full stiff to full soft. Indexing is done in a matter of seconds by rotating the lever or the cup by hand. Indexing the cup to the lever is usually preferable to avoid interference. Adjustment of the ARS system should only be made while the vehicle is unloaded to reduce the load on the springs. NOTE: It is important to make sure that a step in the cup is positioned directly over the tang on the lever. This will prevent damage to the cup and/or lever that can be caused by making partial contact between the tang and a step. In addition, make sure that the lever will not contact any vehicle parts around it, as the suspension moves up. TUNING TIPS—The “softest” setting on the ARS does not mean that the ride will be the most comfortable at that setting. It means that this is the softest spring setting which would be employed on smooth trails or without a load. Excessive suspension bottoming caused by rough conditions or by the addition of a large load will cause a harsh ride when the shock is adjusted to this setting. To eliminate this bottoming, adjust the ARS to the stiffer positions for a more comfortable ride. Hence, sometimes “stiffer is softer.” NITROGEN PRESSURES IN EMULSION SHOCKS

HARLEY DAVIDSON NARROW BEACH HANDLEBAR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Loosen the fuel tank. Refer to FUEL TANK REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

HARLEY DAVIDSON XL BRAIDED FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Drain the brake fluid following the instructions in the service manual. Dispose of waste properly. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Disconnect the battery, negative (-) cable first or remove the main fuse. Follow the instructions in the service manual 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Discard sealing washers, but save bolt for installation. 4. Remove bolt and two sealing washers to disconnect brake line fitting from front brake caliper. Discard sealing washers, but save bolt for installation. 5. Carefully make note of brake line routing, then remove existing brake line. NOTE This kit contains clamps and cable straps to either replace the original equipment clamps and cable straps being removed or to add additional brake line support. INSTALLATION Install proper length brake lines. Incorrect brake line length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00325a) Replace brake line gaskets. Re-using original gaskets can cause brake failure and loss of vehicle control, which could result in death or serious injury. (00318a) Avoid leakage. Be sure gaskets, banjo bolt(s) and brake line are clean and undamaged before assembly. (00323a) 1. Position new sealing washers from kit on each side of hydraulic brake fittings (banjo fittings). Small ID washers are for caliper end, large ID washers are for master cylinder end. 2. Insert bolts (removed earlier) through washers and fittings. 3. Hold new braided brake line in position and install bolts into master cylinder and caliper. Tighten only enough to keep banjo fitting in the same orientation as the stock banjo fitting. 4. Verify there is no twist in the brake line. Adjust brake line if necessary. 5. Install clamps from kit by wrapping clamp around braided brake line at each of the clamp mounting locations. Verify clamps are oriented the same as the stock clamps. Install clamp screws but do not tighten. 6. Check entire length of braided brake line: a. Be sure brake line is not twisted. b. Turn handlebars fully-left and right while checking to make sure brake line does not contact any vehicle components. c. Be sure brake line length between clamps is sufficient. 7. Adjust brake line if necessary. 8. Tighten caliper and master cylinder banjo bolts to 20-25 ft-lbs (27-34 Nm) .

Incoming search terms:

HARLEY DAVIDSON GEAR SHIFTER SHAFT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
Models This kit fits 1982 and later Touring and FL Softail model motorcycles. Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not Sold Separately Gear shifter shaft cover Not Sold Separately Screw, set There are no Service Parts available with this kit. INSTALLATION 1. Remove the stock heel shift lever from the gear shifter shaft. 2. Install the set screw into the gear shifter shaft cover. 3. Install gear shifter shaft cover with installed set screw over the end of the gear shifter shaft. 4. Tighten the set screw until light contact is made with the shaft groove. 5. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw.

Harley-Davidson Motorcycle Services Changeout/ Set Up/ Maintenance/ Repairs

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
The Vendor shall use the custom wiring specifications from the current model year Harley-Davidson set ups. One fully outfitted 2005 model is being decommissioned and may be used as a model for 2006 set up. 2. Attach custom tray, rear box, and custom electronics box to rear mount. Rear box should be attached to the rear of the motorcycle using no more than four mounting holes. The rear box shall be adjusted to the officer assigned to the motorcycle by moving it forward or to the rear and by using spacers to elevate the box for saddlebag lid clearance. 3. Install custom brackets for radio, radar/lidar, flashlight and rear box tray. Brackets from changed-out motorcycles can be used on the new motorcycles and vendor shall modify or reinforce to correct metal fatigue as necessary to maintain functionality. 4. Install all components in the rear electronic box to facilitate repairs and maximize available storage space. These components include power source for cell phone, two-way radio, opticom power supply and auxiliary fuse panel. 5. Set handlebars, hand controls and position of rear tour pack to proper height and alignment for assigned rider. 6. A 5-sided box (base and 4 sides) metal frame is included in 2004 models and will be re fabricated into a 3- sided box (base and 2 sides) and painted black by the Vendor to match existing 2005 models. This arrangement shall allow for a full-size closed-face “Syncrotec” helmet to be stored in the rear tour pack in addition to mounted specialized equipment.

CYLINDER HEAD REPAIR MANUAL

0

Filed Under (Tips and Review) by admin on 28-10-2010

download
ADJUSTABLE CYLINDER HEAD STAND Head can be rotated 360 degrees. Stays in any position using a simple locking mechanism. Use on twin or four cylinder heads. Shipping weight: 14 lbs. Adjustable length-10-1/2″ to 20-1/2″ long x 14″ width x 10-3/4″ high. 35-8602 Cylinder Head Stand VALVE GUIDE DRIVERS Use for removal and installation of valve guides into cylinder head. Available in the following sizes: 35-8418 4.5mm YM-4116 35-8416 6mm YM-4064-A 35-8417 5mm YM-4097 35-8414 7mm YM-1225-A 35-8408 5.5mm YM-1122 35-8413 8mm YM-1200 VALVE GUIDE DRIVER SET (REMOVE & REPLACE) Designed for speed and accuracy, this eleven piece set provides the right tool for the job. Driver set includes two valve guide drivers (5.5mm and 6.6mm), four valve guide installers, one cutter, three cutter pilots (5.5mm, 6.6mm, and 7.7mm) and one tap handle extension bar. 35-9445 Valve Guide Driver Set YAMAHA VALVE GUIDE INSTALLERS These installers are used for installation of Yamaha shoulder less valve guides to a specific depth into the cylinder head. To use, position onto the valve guide and drive into the cylinder head until installer makes contact with cylinder head surface. Note: Must use with Valve Guide Driver. Available in the following sizes: 35-8439 4.5mm YM-4117 35-8437 5.0mm YM-4098 35-8419 5.5mm YM-4015 35-8435 6mm YM-4065-A 35-8423 7mm YM-4017 VALVE GUIDE REAMERS Reaming valve guides after installation assures a proper valve stem to valve guide fit. Available in the following sizes: 35-3829 4.5mm YM-4118 35-3851 7mm YM-1227 35-3836 5.5mm YM-1196 35-3852 8mm YM-1211 35-3847 6mm YM-4066 CLOVER VALVE LAPPING COMPOUND KIT The world famous green can with the four leaf clover. For seating valves, mating gears, and sharpening. Sold as a kit with coarse 120 grit (roughing) and 280 fine grit (finishing). 35-0309 Clover Valve Lapping Compound VALVE LAPPING TOOL The ultimate vacuum stick for insuring perfect surfaces on valves and valve seats. Interchangeable cups make unit suitable for use with virtually any size valve. Set includes vacuum stick, 3/4″ and 1/4″ diameter rubber cups. 35-8998 Valve Lapping Too

Incoming search terms:

Incoming search terms: