what should i torque my harley dyna shocks to

You search Auto repair manual PDF what should i torque my harley dyna shocks to, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what should i torque my harley dyna shocks to Direct Download speed 5282 Kb/s

  what should i torque my harley dyna shocks to Full Version speed 6162 Kb/s



Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

Ultima Billet Rear Shocks Installation Instruction Sheet

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
Unloading the rear suspension Use a jack under a flat part of the motorcycle and lift until the rear tire is barely resting on the surface. This ensures that the shocks are unloaded. They are now ready for removal. Remove the old shocks Refer to the service manual specific to your motorcycle for this process. Unbolt the old shocks. Save the necessary hardware if you have not purchased new hardware. Installation Shocks should be installed with the preload adjuster on top (see Preload Adjustment). With the new shocks in hand; please go over the hardware configuration diagram (Figure 3) to decide which configuration best fits your application. Spacers are included to provide clearance between the shocks and your motorcycle (Figure 4). Typically start on which ever side the final drive is located. This side normally causes the clearance issues. Each eye and each side should be configured the same way. Make sure to use the proper hardware so that the shock- bushings fit the shock-bolts as snugly as possible. Shocks come with a 1/2″ ID bushing installed. This is needed for all applications. An optional bushing is included and should be used in addition when 3/8″ bolts are used instead of the larger 1/2″bolts. Unless new hardware was purchased, you will use the stock bolts from your old shocks to install the new shocks. Use Red Locktite (or equivalent) and use a torque wrench to tighten as follows: Models that use 1/2″ bolts: 65ft-lbs Models that use 3/8″ bolts: 30ft-lbs (Figures 1 & 2) Be sure to check clearance between the shock and the belt-guard. If there is any contact you will need to alter your spacer arrangement to accommodate this. Check tire to fender clearance as well. This clearance will be reduced when lowering shocks are used. Preload Adjustment Your new Ultima Billet Shocks are preload adjustable. Adjustment should be done once the shocks are installed. To adjust use a strap wrench and turn the top part of the shock (Figure 6) clock-wise to tighten or provide more preload (this stiffens the suspension), or counter-clockwise to loosen or subtract preload (this softens the suspension). Hand adjustments may be sufficient on models with smaller spring rates while the strap wrench will be required on the high spring rate shocks. You will see notches (Figure 6) that appear on the shock as the shock is preloaded. These should help you obtain the same preload for both sides of the motorcycle. Both shocks should be adjusted to the same level of preload.

Incoming search terms:

HARLEY-DAVIDSON SOFTAIL MODELS STEALTH AIR SHOCK MOUNTING

0

Filed Under (Harley Davidson) by admin on 16-12-2010

download
INSTALLATION 1. Remove the seat, inner fender, and ignition coil cover. Removing the rear wheel assembly is recommended for ease of installation, but not absolutely necessary. Remove the nut cup and outer grommet on each of the Works shocks. If you intend to leave the ride height at stock height for road riding, position the inner nut cup SHOC KS SHOC KS WORKS PERFORMANCE PRODUCTS, INC. 21045 Osborne St., Canoga Park, CA 91304 818.701.1010 fax 818.701.9043 STEALTH AIR SHOCK MOUNTING FOR HARLEY-DAVIDSON SOFTAIL MODELS 2000-ON #HDAIR-00 – 02/15/2006 WARNING! THESE SHOCKS MUST ONLY BE USED WITH STOCK SWINGARMS AND ON STOCK FRAMES WITH THE STOCK BOTTOMING BUMPERS ON THE CHASSIS TO LIMIT THE TRAVEL OF THE SHOCKS. AFTERMARKET SWINGARMS, OR MODIFIED SWINGARMS THAT DO NOT HAVE THE UPPER BRACE THAT ACTS AGAINST THE BOTTOMING BUMPERS CANNOT BE USED WITH THESE SHOCKS. INCREASING THE TRAVEL BY ELIMINATING THE BUMP STOPS OR A NON-STANDARD SWINGARM DESIGN WILL ALLOW THE TIRE TO MAKE CONTACT WITH THE FENDER OR OTHER CHASSIS COMPONENTS, AND CAN DAMAGE THE SHOCKS. 19. Lock Washers 20. Long Bolts (2) 21. Short Bolts (2) 13. Din Plug Screw 14. Din Plug Gasket 15. Cap 16. Eye Spacers (4) 17. Cotter Pins (2) 18. Switch Bracket 7. Compressor Bracket 8. Harness 9. Fuse Block 10. Din Connector 11. Solenoid 12. Hose 1. Damper Shock 2. Air Spring Shock 3. Nut Cup 4. Grommet 5. Hose 6. Compressor 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 14 18 19 20 21 Fig. 1–Nomenclature on the damper shock up against the ring nut. The shocks are now ready to install. 2. Place the motorcycle on a suitable frame stand allowing unrestricted access to the shocks. 3. Place a small screw jack under the swing arm to support the weight as well as allow you to position the swing arm correctly to line up the shock mounting bolts. Remove stock shocks. 4. Install the left side (damping) shock with the stock mounting bolt. Make sure that the bolt threads and threaded portions of the frame are free of oil and grease. Grease the shoulders of the bolts and use thread lock compounds on the threads. Discard the stock shock washers on both shocks. Do not use any washers- -including the stock washers on these bolts. Use only the spacers included. The 3/16-inch wide spacers are used on each side of the shock eye. Do not “double-up” the spacers together on either side of the shock eye, as this will cause misalignment of the shocks which can lead to premature wear or damage to the shocks. 5. Put the supplied spacers on each side of the eye. The shoulder of the bolt must protrude a small amount through the shock eyes in order to allow the shock to pivot freely. This is extremely important. With the shocks fully tightened, the spacers should be free to rotate with finger pressure. If the washer is used or a non-stock bolt is used, the bolts will work loose or break because the shocks are in a bind.

2000 & later Harley Davidson Softails Drag Specialties Shocks Installation Manual

0

Filed Under (Harley Davidson) by admin on 31-03-2012

download
1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hard- ware. 3. Before reinstalling a Drag Specialties adjustable ride height shock, spin the non-flanged nut all the way onto the stud mount, followed by a bushing-cup, bushing, and sleeve. Then install shocks as you would a stock unit, following an authorized shop manual. With the non-flanged nut spun all the way onto the stud, the stock ride height is achieved. Once you have installed the other bushing, bushing-cup, and flanged nut you can now install the safety E-clip. This E-clip is snapped into the groove near the end of the stud mount where the threads stop. This is to serve as a reference point ONLY – when the flanged-nut reaches it you have lowered your ride height the maximum 2 inches. DO NOT torque the flange-nut against the E- clip (see figure 1). 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs). 5. Drag Specialties shocks have adjustable pre-load to compensate for varying weights. A Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley

HARLEY DAVIDSON DYNA AND SPORTSTER Chrome Front Wheel Spacers INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Block motorcycle underneath frame so front wheel is raised off the ground. 2. See Figure 1. Remove the upper (1) and lower (2) brake caliper mounting bolts and brake caliper(s) (3). Support caliper(s) using a rubber bungee cord. Be careful not to scratch fender paint. NOTES Do not operate front brake lever with the front wheel removed or the caliper piston may be forced out of piston bores. Reseating the piston requires disassembly of the caliper. Prior to removal, make note of existing left and right spacer location. The new spacers will be installed in the locations. 3. See Figure 3. On left side of wheel, remove axle nut (D), lockwasher (E) and washer (F). Perform the following: 4. Sportster and Dyna (except FXDWG) See Figure 2. Loosen the pinch bolt nut (1) and pull the the axle (2) free. Remove wheel and spacers. Leave bearing(s) in place. Discard spacers. 3 1 2 is04469 1. Brake caliper mounting bolt, long (top) 2. Brake caliper mounting bolt, short (bottom) 3. Brake caliper Figure 1. Caliper Mounting Bolts (Left Side) Dyna and Sportster 3 1 2 is04470 1. Pinch bolt nut 2. Axle 3. Pinch bolt Figure 2. Front Wheel Mounting (Dyna and Sportster Except FXDWG-Right Side) 5. See Figure 3. Obtain the new right (1) and left (2) chrome spacers from kit and install. 6. Apply a light coat of ANTI-SEIZE LUBRICANT (Harley- Davidson Part Number 98960-97) to the axle.
7. Place wheel between sliders and install axle. Verify that axle spacers on right and left side are properly installed. 8. See Figure 3. Install the washer (F), lockwasher (E) and nut (D) onto threaded end of axle (A). 9. In order to properly align the front fork, perform the fol- lowing: a. On the right side of the wheel, insert a 7/16 inch drill bit through the hole in the axle. While holding axle stationary, tighten axle nut to 50-55 ft-lbs (61.0-74.6 Nm) . b. Pull fork leg so that it just contacts drill bit. Tighten according to the following: c. Refer to Figure 2. Tighten the Axle Pinch Bolt Nut to 25-30 ft-lbs (33.9-40.7 Nm) . d. Remove drill bit from axle hole. 10. Follow instructions in Service Manual and install brake caliper to the sliders noting the following: •Loosely install long bolt to the top hole on fork leg. Install the short mounting bolt to the bottom hole and tighten to 28-38 ft-lb (38.0-51.5 Nm) . •Final tighten top bolt to 28-38 ft-lbs (38.0-51.5 Nm) . 11. Repeat Step 10 to install brake caliper on opposite side of wheel. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) 12. Pump brake lever to move pistons out until they contact both brake pads. Verify piston location against pads

Incoming search terms:

440 Series Shocks Installation Manual

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Follow instructions in an authorized shop manual or take the motorcycle toacompetent dealer. The motorcycle must be on thecenterstand (if equipped) or securely blocked to prevent it from tipping over when the shocks are removed. Failure to do so can cause serious damage and/or injury. The use of any lowering blocks is not recommended and will void the warranty. Make sure that proper bushings/sleeves are installed in the shocks. Improper bushings/sleeves can cause unsatisfactory and/or unsafe operation (seethe instructions packaged with the mounting hardware). 1. Place a quality jack or sufficient blocks under the motorcycle to securely lift the rear wheel slightly off the ground. 2. Using the correct shop manual, remove the old shocks and note location of the mounting hardware. If additional accessories are installed on your motorcycle, please refer to their mounting instruc- tionsforremoval to gain access to your shocks. 3. Before installing your new Progressive shocks you need to check the tire to fender clearance, (see Ain figure1) making sure that the tire does not come in contact with the fender. If the rear fender or tire has been changed to anything other than stock, a travel limiter maybe required. On some models with side bags or luggage, removal of the lower cover maybe required to eliminate any interference. Install shock assemblies onto the motorcycle (shaft end must be down!) and tighten bolts/nuts to proper torque. Check the clearances of the shock to frame (B) and shock to chain, chain guide, disc caliper and linkage (C) in figure 1. The lower cover can be removed for clearance if necessary. 4. Reinstall any accesso- riesremovedin accord with their mounting instructions. Make sure accessories do not in- terferewith shocks throughout full travel. If any accessories bolt to shock mounting points, a careful inspection must be made to insure that they do not bind the shocks in anyway (see figure 2)

Harley Davidson 1990 and later HSR Choke Cable Installation Manual

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
The majority of HSR42/45 installations use the Harley cable. Installation is simple when the installation instructions are followed, step by step. Those steps are: • Remove the stock Harley choke cable assembly. • Remove the spring and plunger from the stock cable. • Remove the Mikuni “Starter Nut” from the HSR. • Remove the Mikuni spring and plunger from the HSR. • Install the Mikuni spring and plunger on the Harley choke cable. • Install the Harley choke cable with the fitted Mikuni spring and plunger into the HSR carburetor. • DO NOT use the Mikuni Starter Nut; discard it. • DO NOT use the Harley spring or plunger; discard them. Note: If you do not have installation instructions, you may download them from the www.mikuni.com website in the “manuals” section. If the Mikuni Starter Nut is fitted to the Harley cable, the choke plunger is held off its seat and the choke is open all the time. If the Harley spring and plunger are used, the plunger does not seal and the choke is open all the time. The result, in both cases, is very poor fuel mileage (30 mpg or less). Another possible cause of poor mileage, rough idle and fouled spark plugs is incorrect cable routing. The stock Harley choke cable is very stiff and may not be fully seated in the metal elbow at the carburetor end of its run. This condition is easily corrected. On occasion, one of these errors may have been made by someone else at another location. The unfortunate mechanic who inherits the task of correcting the rich condition, poor idle and poor fuel mileage may have no clue as to the mismatch of parts. For this reason, we include the photos and text to help you discover if your installation is correct.

Incoming search terms:

HARLEY DAVIDSON DYNA GLIDE CUSTOM SEAT KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat from motorcycle. Keep lockwasher and screw. 2. Remove existing grab strap and all attaching hardware. 3. Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). 4. On all models, except FXDWG , install existing stock rear bracket onto seat using stock hardware. On FXDWG models, install the new rear bracket, 52152- 97 onto the seat using the stock hardware. 5. Position new seat on motorcycle. Be sure bracket on front of seat fully engages seat mounting tab on frame. NOTE On rear fenders of 1997 -2003 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997 – 2003 models. 1996 DYNA MODELS ONLY Secure seat with stock screw, stock lockwasher and place stock nylon washer between seat bracket and fender. 1997 – 2003 DYNA MODELS Secure seat with stock screw and stock lockwasher.

Incoming search terms:

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms: