what size hex head wrenches are used on harley ultra classic shifter lever and shifter linkage

You search Auto repair manual PDF what size hex head wrenches are used on harley ultra classic shifter lever and shifter linkage, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what size hex head wrenches are used on harley ultra classic shifter lever and shifter linkage Direct Download speed 5282 Kb/s

  what size hex head wrenches are used on harley ultra classic shifter lever and shifter linkage Full Version speed 6162 Kb/s



HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

HARLEY DAVIDSON CUSTOM HAND LEVER KIT BRAKE LEVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. See Figure 1. Squeeze the brake lever and place the cardboard insert between the brake lever and lever bracket. NOTE Use the eyelet of an ordinary cable strap if the cardboard insert is not available. NOTE Do not remove the handlebar clamp or switch housing assembly to remove the brake lever. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 2. See the Figure 2 and the FRONT BRAKE MASTER CYLINDER section of the Service Manual. Remove the retaining ring (B) from the groove in the pivot pin (C). Inspect the retaining ring (part number 11143) and replace if needed. 3. Remove the pivot pin and retain for re-use. Remove and discard the original equipment brake lever and pivot lever bushing. 4. Insert the pivot lever bushing (2) from the kit into the new brake lever (1). NOTE Follow the instructions in Steps 4 and 5 carefully in order to prevent the actuating tab on the brake lever from damaging the rubber boot and plunger of the front stoplight switch. -J04165 1 of 3
5. Gently press and hold the piston cap (A) forward with a screwdriver. Slip the brake lever into position and align the pivot pin holes. 6. Install the pivot pin and retaining ring removed in Steps 1 and 2. 7. Check the front brake for proper operation. There should be no free play in the hand lever. A slight preload is per- missible. A plugged or covered relief port can cause brake drag or lock-up, which could lead to loss of control, resulting in death or serious injury. (00288a) 8. To verify proper operation of the master-cylinder relief port, actuate the brake lever with the reservoir cover and gasket removed. A slight spurt of fluid will break the surface if internal components are working properly. 9. Reinstall the master cylinder cover. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 10. Check that the stop light goes on when the brake lever is actuated. CLUTCH LEVER INSTALLATION See the CLUTCH CONTROL section of the appropriate Service Manual for all clutch lever removal, installation and adjustment procedures.

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON HAND LEVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
BRAKE LEVER INSTALLATION Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 1. 5/32 in. (4 mm) Cardboard Insert 1. See Figure 1. Squeeze the brake lever and place the cardboard insert between the brake lever and lever bracket. NOTE Use the eyelet of an ordinary cable strap if the cardboard insert is not available. NOTE Do not remove the handlebar clamp or switch housing assembly to remove the brake lever. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 2. See the Figure 2 and the FRONT BRAKE MASTER CYLINDER section of the Service Manual. Remove the retaining ring (4) from the groove in the pivot pin (B) and discard retaining ring. 3. Remove the pivot pin and retain for re-use. Remove and discard the original equipment brake lever and pivot lever bushing. NOTE New brake levers come with the pivot lever bushing installed. NOTE Follow the instructions in Steps 3 and 4 carefully in order to prevent the actuating tab on the brake lever from damaging the rubber boot and plunger of the front stoplight switch. -J04342 1 of 3 4. Gently press and hold the piston cap (A) forward with a screwdriver. Slip the brake lever into position and align the pivot pin holes. 5. Install the pivot pin removed in Step 2 and new retaining ring (4) from kit. 6. Check the front brake for proper operation. There should be no free play in the hand lever. A slight preload is per- missible. A plugged or covered relief port can cause brake drag or lock-up, which could lead to loss of control, resulting in death or serious injury. (00288a) 7. To verify proper operation of the master-cylinder relief port, actuate the brake lever with the reservoir cover and gasket removed. A slight spurt of fluid will break the surface if internal components are working properly. 8. Reinstall the master cylinder cover. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 9. Check that the stop light goes on when the brake lever is actuated. CLUTCH LEVER INSTALLATION See the CLUTCH CONTROL section of the appropriate Service Manual for all clutch lever removal, installation and adjustment procedures. SERVICE PARTS

1951 AJS MAINTENANCE MANUAL AND INSTRUCTION BOOK

0

Filed Under (AJS) by admin on 31-10-2010

download
Throttle twist grip. On right handlebar. Twist inwards to open. When fully closed engine should just idle when hot. Air lever. Small lever on right handlebar. Pull inwards to increase air supply to carburetter. Once set, when engine has warmed up, requires no alteration for different road speeds. Should be fully closed when starting engine from cold. Ignition lever. Small lever on left handlebar. Advances and retards ignition point. Pull inwards to advance on touring models (retard on competition models). Retard two-fifths of total movement for starting. Valve lifter lever. Small lever close to clutch lever. Lifts exhaust valve from seat, releasing compression in combustion chamber, enabling engine to be easily rotated for starting. Also used for stopping engine if throttle stop is set as advised above. Clutch lever. Large lever on left handlebar. Grip to release clutch so that drive to rear wheel is disconnected. Used when moving away from a standstill and when changing gear. Front brake lever. Large lever on right handlebar. Grip to operate front wheel brake and, for normal braking, use in conjunction with rear brake application. Rear brake lever. Pedal close to left side foot rest. Depress with left foot to apply rear brake. Apply gently and use increasing pressure as the road speed decreases. Gear change lever. Pedal in horizontal position close to right foot rest. Con­ trols selection of the four speeds, or ratios, between engine and rear wheel revolutions, with a ” free,” or neutral, position. See illustration 3. Kick-starter lever. Vertical pedal on right hand side of gear box. Operated to start the engine. Lighting switch. In top of head lamp. Controls lamps by a rotating lever which has three positions : (1) “OFF” Lamps not on. (2) ” L ” Pilot bulb in head lamp and rear lamp and speedometer lamp on. (3) ” H ” Head and rear lamp and speedometer lamp on. Ammeter. In top of head lamp. Indicates flow of electric current, in, or out, of battery. (” Charge ” or ” Discharge.”) Horn switch. Press switch on right handlebar. Depress button to sound horn. Gear box filler cap. Located on top edge of kick-starter case cover. Allows insertion of lubricant and access to clutch inner wire. Footrest for rider. One located each side of machine. Petrol tank filler cap. Located in top of fuel tank. To release, slightly depress, turn fully to the left, and then lift away. There are two locking positions. The middle position, between the fully tightened down and ” lift away ” positions, is in the nature of a ” safety ” device to prevent loss that might be occasioned by unauthorised meddling. Oil tank filler cap. Located on top edge of oil tank. The construction and operation is exactly as the petrol tank filler cap. Dipping switch. Trigger switch on left handlebar. Used to select normal or ” dipped ” beam of head lamp when main lighting switch lever is in the ” H ” position. (The head lamp bulb has two filaments.

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

1954 AJS MAINTENANCE MANUAL INSTRUCTION BOOK

0

Filed Under (AJS) by admin on 31-10-2010

download
Throttle twist grip. On right handlebar. Twist Inwards to open. When fully closed engine should just idle when hot. Air lever. Small lever on right handlebar Pull Inwards to Increase air supply to carburetter. Once set, when engine has warmed up, requires no alteration for different road speeds. Should be fully closed when starting engine from cold, Ignition lever. When fitted. Small lever on left handlebar. Advances and retards ignition point. Pull Inwards to retard. Retard two-fifths of total movement for starting. Valve lifter lever. Small lever close to clutch lever. Lifts exhaust valve from seat, releasing compression In combustion chamber, enabling engine to be easily rotated for starting. Also used for stopping engine if throttle stop is set as advised above. Clutch lever. Large lever on left handlebar. Grip to release clutch so that drive to rear wheel is disconnected. Front brake lever. Large lever on right handlebar. Grip to operate front wheel brake and, for normal braking, use in conjunction with rear brake application. Rear brake lever. Pedal close to left side foot rest. Depress with left foot to apply rear brake. Apply gently and use increasing pressure as the road speed decreases. Gear change lever. Pedal in horizontal position close to right foot rest. Controls selection of the four speeds, or ratios, between engine and rear wheel revolutions, with a ” free,” or neutral, position. See Illustration 2. Kick-starter lever. Vertical pedal on right hand side of gear box. Lighting switch, in top of head lamp. Controls lamps by a rotating lever which has three positions : (1) “OFF” Lamps not on. (2) ” L ” Pilot lamps, rear lamp and speedometer lamp on. (3) ” H ” Main head lamp, rear l amp and speedometer lamp on. Ammeter. In top of head lamp. Indicates flow of electric current, in, or out, of battery. (” Charge ” or ” Discharge.”) Horn switch. Press switch on right handlebar. Gear box filler cap. Located on top edge of kick-starter case cover. Allows Insertion of lubricant and access to clutch inner wire and internal clutch operating lever. Footrest for rider. Petrol tank filler cap. Located in top of fuel tank. To release, slightly depress, turn fully to the left, and then lift away. There are two locking positions. The middle position, between the fully tightened down and ” lift away ” positions, is in the nature of a ” safety ” device to prevent toss that might be occasioned by unauthorised meddling. Oil tank filler cap. Located on top edge of oil tank. The construction and operation is exactly as the petrol tank filler cap. Dipping switch. Trigger switch on left handlebar. Used to select normal or ” dipped ” beam of head lamp when main lighting switch lever is in the ” H ” position. (The main head lamp bulb has two filaments.)