what size is the fuse on tao tao 125 cheetah fuse size

You search Auto repair manual PDF what size is the fuse on tao tao 125 cheetah fuse size, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what size is the fuse on tao tao 125 cheetah fuse size Direct Download speed 5282 Kb/s

  what size is the fuse on tao tao 125 cheetah fuse size Full Version speed 6162 Kb/s



YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

Harley Davidson Power Pod Switch Housing Throttle Bracket Installation Instructions

0

Filed Under (Harley Davidson) by admin on 19-03-2012

download
Attach the “Y” bracket to the Power Pod by using the two Power Pod socket head screws that come in your parts kit. (This bracket may already be attached from the factory. ) 2) Remove the two screws on the Right Hand switch housing on your Harley Davidson motorcycle and reinstall them through the two “Y” bracket open holes and back into the switch housing holes. Tighten snugly. In this mounting position, the heads of the two socket head screws holding the “Y” bracket to the Power Pod should be touching the handlebar; this is necessary as it grounds the unit for proper operation. If the unit is not grounded properly, it will not operate. 3) Run the Power Pod’s 60″ power cord to your battery. Make sure as you hide the cord on the way to the battery, that your handlebars turn freely and that the cord does not come in contact with hot engine parts that may melt the wire over time. 4) At some point, before reaching the battery, attach (using the two butt connectors) the in-line fuse holder. TIP: Keeping the in-line fuse holder in an easy to access place (like under a side panel etc) rather than under the seat, may help you service the fuse easier in case of a blown fuse. In most cases, it’s easier to pull a side panel off than it is to remove a seat! 5) Attach the Power Pod lead wire (with in-line fuse now already attached) directly to the battery for power at anytime without using the key. The hot lead can also be run to the fuse box which will require using the ignition switch to “Accessory” or “ON” in some cases. TIP : Always use the in-line fuse for safety. 6) Insert the 20 amp fuse into the in-line fuse holder. Strap down with zip-ties any loose wires and you’re done!

2010 CSR Naked 125 Engine and transmission Chassis, suspension, brakes and wheels

0

Filed Under (CSR) by admin on 27-10-2010

Model: CSR Naked 125 Year: 2010 Category: Naked bike Rating: Price as new (MSRP): Euro 2199. Prices depend on country, taxes, accessories, etc. Engine and transmission Displacement: 124.80 ccm (7.62 cubic inches) Engine type: Single cylinder, four-stroke Fuel system: Carburettor Cooling system: Liquid Transmission type, final drive: Chain Chassis, suspension, brakes and wheels Frame type: Steel Front tyre dimensions: 90/90-13 Rear tyre dimensions: 130/90-15 Front brakes: Single disc Rear akes: Single disc Physical measures and capacities Dry weight: 161.0 kg (354.9 pounds) Weight incl. oil, gas, etc: 179.0 kg (394.6 pounds) Overall height: 1,085 mm (42.7 inches) Overall length: 2,110 mm (83.1 inches) Overall width: 650 mm (25.6 inches) Fuel capacity: 18.00 litres (4.76 gallons) Other specifications nStarter: Electric Color options: Black, silver Comments: Also called NKT 125. Spanish brand. Further information Parts and accessories Check out parts and accessories from our partners.nAsk questions Join the 10 CSR Naked 125 discussion group. Insurance, loans, tests Check out insurance here. Search the web for dealers, loan costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs

Incoming search terms:

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

MZ 125 SXJSM Repair Manual

0

Filed Under (MZ) by admin on 18-11-2010

download
Front suspension · Design Telescopic fork · Spring travel 220 mm Rear suspension · Design long swinging fork · Spring travel/adjustment 220 mm/adjustable spring base Steering bearing Deep groove ball bearing Clutch lever and throttle twist grip · Play in the clutch lever 3-5 mmattheendofthe clutch · Play in throttle Bowdencable 2-3 mmatthetwist grip flange Wheels – spoked wheels Variant MZ125 8X Variant MZ125 8M Front tire 90/90 -21 110170-17 Tire pressure 190 kPa/1,9 bar/28 psi 180 kPal1,8 bar/26 psi Rim size 1.85×21 3.00 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Rear tire 120/80 – 18 130170-17 TIre pressure (value at perm. axle load) 200 (250) kPa/2 (2,5) bar/29 (36) psi 230 (260) kPal2,3 (2,6) bar/33 (66) psi Rim size 2.50 x18 3.50 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Front wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper I and manually operated cylinder · Outside diameterxplate thickness 280x4mm · Thickness of the brake pad 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 11 mm · Brake caliper cylinder inside diameter 2×25,4 mm · Brake fluid DOT4 Rear wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper and manually operated cylinder · Outside diameterxplate thickness 220x4mm · Thickness of the brake pad (wear limit) 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 13mm · Brake caliper cylinder inside diameter 2x 25,4mm · Brake fluid DOT4 Brake level and brake pedal · Play in brake lever 2-5 mmattheendofthe brake lever · Position of brake pedal 25 mmunderthe footrest rubber surface

Harley-Davidson Valves, Guides And Seats Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1: Clean carbon from old guide O.D. before removal. 2: Guide to head press fit .0015″ / .002″ (head smaller than guide). 3: Heat head to approximately 200° – 250° F. 4: Install the guide at room temperature (Head hot & Guide at room temperature). 5: Let head cool to room temperature before final sizing of the bore. 6: Determine desired clearance valve to guide. Recommended clearance Shovel Head with cast iron guides Intake .001″ – .0015″ Exhaust .0015″ – .002″ (Ampco-45 add .001″) 7: Select the correct plug gage by adding the valve stem diameter and clearance desired for the finish diameter. 8: Select a plug gage .0005″ under finish size for the other end of the handle. 9: Finish hone the bore to size, check the size as you hone with the -.0005″ under size pin gage, finish hone to size with the finish plug gage pin. 10: Cut or Grind the seats, lap the valves to seats and check valve seat concentricity before assembling valve springs. 11: Use a good assembly lube, S’NS works great. 12: Use valve stem seals. Factory OE seals will stay tight with guide top size +.005″ to -.015″ from published size. 13: After the head is assembled and still on the bench check for any leakage valve to seat

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

2011 APRILIA RS4 125 Engine and transmission Specifications

0

Filed Under (Aprilia) by admin on 24-11-2010

Engine type: 1 cylinders, 4-stroke, Single
Displacement: 125 cc (7.64 cubic inches)
Bore × stroke: 58 mm × 47 mm (oversquare – shortstroke)
Cooling system: Water cooled
Power: 16.04 HP (11.8 kW)
Throttle: Cable operated
Valves
Valve train: DOHC, variable
Valves per cylinder: 4
Fuel and ignition
Sparks per cylinder: 1
Fuel supply system: Fuel injection
Ignition type: Digital CDI
Compression: 12.5:1
Engine mounting: Transverse
Lubrication system: Wet sump
Gear box: Manual 6-speed
Clutch: Wet, multiple discs, cable operated
Final drive: Chain
Starter: Electric
Dimensions
Physical measures
Length: 1953 mm
Width: 740 mm
Height: 1138 mm
Wheel base: 1350 mm
Seat height: 820 mm
Weight
Curb weight: 120 kg

Aprilia Sportcity One 125 Technical Specifications

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Engine Single cylinder 4-stroke. Forced air cooling. 2 valve head with overhead camshaft. Fuel Unleaded petrol. Bore and stroke 57 x 48.6 mm. Displacement 124 cc. Compression ratio 12:11 (125 cc). Maximum power 7.0 kW (9.52 HP) at 8,000 rpm. Max torque 10.04 Nm at 7,000 rpm. Fuel system Carburettor, Ø 26 mm. Ignition Electronic inductive discharge ignition with variable advance. Starting Electric. Alternator 300 W. Lubrication Wet sump. Forced circulation with mechanical pump. Gearbox Automatic variator. Clutch Automatic centrifugal dry clutch. Primary drive V belt. Final drive Gearbox. Frame Single cradle frame in high strength steel tube. Front suspension Hydraulic telescopic fork with 32 mm stanchions. Wheel travel 85 mm. Rear suspension Engine unit acting as swingarm. Single hydraulic shock absorber with adjustable spring preload. Wheel travel 84 mm. Brakes Front: 220 mm stainless steel disc with twin piston floating caliper. Rear: 140 mm drum. Wheels Light alloy. Front: 3.00 x 14″. Rear: 3.50 x 14″. Tyres Tubeless. Front: 120 / 70 x 14″. Rear: 120 / 70 x 14″. Dimensions Overall length: 1950 mm. Overall width: 740 mm. Wheelbase: 1358 mm. Seat height: 775 mm. Fuel tank Capacity 7.5 litres (including 1.5 litre reserve)

Incoming search terms: