what type of cruise control devices for an iso grip on a 2003 honda vtx 1800

You search Auto repair manual PDF what type of cruise control devices for an iso grip on a 2003 honda vtx 1800, if there are search results will appear below. If search results do not exist, please search by others keyword.



  what type of cruise control devices for an iso grip on a 2003 honda vtx 1800 Direct Download speed 5282 Kb/s

  what type of cruise control devices for an iso grip on a 2003 honda vtx 1800 Full Version speed 6162 Kb/s



HARLEY DAVIDSON CRUISE CONTROL KIT FOR FLHR/I AND FLHRS/I MODELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove seat, left saddlebag, left side cover and air cleaner assembly following instructions in applicable Service Manual. 2. Review the CRUISE CONTROL-ULTRA MODELS section in the applicable Service Manual before attempting to install this kit. Install Cruise Control Module To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the appropriate Service Manual and remove bat- tery. 1 is04799 1. Cruise control module mounting hole (3) Figure 1. Battery Box (Right Side View) 2. See Figure 1. In battery box, identify the location of the three mounting holes (1) (on left side of panel) for mounting the cruise control module. 3. See Figure 10. Obtain the cruise control module (1) with cruise cable attached and three grommets (5) from kit. Install the grommets on studs of cruise control module with small diameters outward. 4. See Figure 2. While holding cruise control assembly in place near its mounting location, feed the cruise control cable through the hole in frame crossmember plate and route under rear spark plug wire staying on inner side of fuel line components. Carefully curve cable toward the right and continue routing up under the fuel tank and over the top of the engine stabilizer bracket, then down between cylinder heads. Leave in place temporarily. 5. See Figure 10 and obtain a harness retainer (4) from kit and secure the cruise cable to crossmember plate with barb as shown. On California models, remove the EVAP hose from cable clip and secure hose with one of the cable strap (8)

Incoming search terms:

BMW K1100LT Installing Real Cruise Control

0

Filed Under (BMW) by admin on 26-10-2010

download
The vacuum reserve canister (VRC) is used to provide adequate vacuum for the cruise control servo unit. It uses the throttle body as a vacuum source and, via the vacuum check valve, stores up vacuum for the servo to use to pull the throttle cable. You can also buy one of these at an auto parts store for about $10-15 but I decided to build my own so I could make one that would fit inside the left front of the main fairing body. If you decide to buy one, make sure you can return it if it doesn’t fit inside the fairing or be prepared to mount it somewhere else like inside the tail cowl. I used 8″ of 2″ diameter PVC tubing because that is the length that would easily fit inside the fairing It is mounted inside the fairing in front of the left “bucket.” I used white PVC tubing but, in hindsight, would use black if possible since it is visible to the rider when mounted in the fairing. I suspect that the cruise control may actually work without the use of the vacuum canister so you might want to try the cruise without a VRC. If you do install the cruise control without a VRC, you’ll want to put a vacuum check valve in the vacuum hose that goes from the throttle body to the cruise control servo unit.
11/30/2005 08:23 PM Installing Real Cruise Control on a BMW K1100 Page 4 of 8 used epoxy for assembling the VRC as it’s my permanent adhesive of choice. Cut an 8″ length of 2″ diameter PVC tubing. Sand the edges. Drill two holes as shown for the check valve and vacuum tee. There’s a vacuum tee in the bags of installation miscellany that come with the cruise control. File the webbing from the right angles before gluing it and the check valve in place. Remember to glue the tee into place before gluing the end caps on. Make sure everything has an airtight seal. I used zip-ties to hold it in place inside the main fairing body in front of the left bucket

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

Incoming search terms:

Yamaha Road Star Forward Control Kit Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Before starting to assemble this forward kit on your motorcycle check the packing list to make sure that the kit you received is the correct one for your model motorcycle and that the foot pegs are the style you ordered (billet or ISO). Next check the contents hardware kit P.N.0109-1000 against the packing list for completeness. Installing The Shift Control Photo 1 Remove wires from horn. Remove the two hex head bolts (Save for later installation) that mount the OEM shift controls to your motorcycle. Unthread stock shift rod at trans shift arm, leaving OEM rod end connected to stock shift arm. Using Original Metric hardware, place a drop of Loctite #242 (blue) to the bolt threads and mount the shift control plate to the motorcycle frame, Photo 2. FORWARD CONTROL KIT PM SHIFT CONTROL ASSEMBLY Note Before torquing the shift control mounting bolts down, tighten them snug and look behind the shift control mounting plate to where it contacts the mounting lug on the frame. Make sure it fits squarely to the lug before proceeding further. Torque the two shift control mounting bolts down to 25 ft-lb. Using a 3/8″ x 1″ hex head bolt with a lock and flat washer put a drop of Loctite #242 (blue) on the threads and insert the bolt through the rear of the control mounting plate and attach the foot-peg pivot to it. Tighten the bolt while holding the footpeg pivot so that its hinge is lined up in a 45˚ rear facing angle. Thread supplied shift rod coupler to stock shift rod end at trans arm. Mount the shift pedal to the other end of the shift ro d using a 5/16″ x 1″ socket head screw and Nylocnut . Adjust the transmission shift linkage so that the shift arm on the forward controls and the shift arm on the transmission are parallel. Secure it with the jam nuts. Apply a drop of Loctite #242 (blue) to the threads under the jam nut before tightening see Photo 3 After you have assembled the shift control onto your motorcycle you must align the footpeg. The folding footpeg assembly uses a blind stud to attach the footpeg to the footpeg pivot. Shim washers (3/8″ x .015″) are used on the stud between the footpeg and the pivot, see Photo 4, so that the top surface of the footpeg is correctly aligned for your foot when it is tightened down on the pivot. This is done by setting a couple of shim washers on the footpeg mounting stud “A” and then screwing the footpeg onto the mounting stud, if the footpeg is rotated to far forward then add another shim washer, if not far enough then remove a shim washer. After you have the selected the correct number of shims for your footpeg, disassemble the footpeg and put a drop of Loctite #271 (red) on both ends of the stud and reassemble the footpeg. This will also need to be done on the brake control footpeg. Setting Up the Master Cylinder The master cylinder pushrod return spring and pushrod boot must be installed on the master cylinder before it is assembled onto the forward control mount. The parts are shown in Photo 5: pushrod boot (A), pushrod return spring (B), spring seat washer (C), and master cylinder (D). Place the return spring seat washer into bore of master cylinder so that is sits on top of the piston retaining snap ring. Next set the pushrod return spring on the seat washer and slide the pushrod boot over the return spring now slip the big end of the boot over the flange on the master cylinder so that the ridge on the inside of the boot fits into groove “A” that is machined into the end of the master cylinder flange, see Photo 6. Installing The Brake Control Unplug stock brake light switch at master cylinder. Remove brake line from rear caliper. Remove the existing brake controls from your motorcycle down to the control mounting lug that is welded on to the frame’s right side, see Photo 8. Save Metric hardware for later use. A Shim Washer PHOTO 4 A B C D PHOTO 5 A PHOTO 6 PHOTO 7 Note For complete brake system removal instructions and precau – tions refer to the appropriate service manual for your year and model motorcycle

Incoming search terms:

BMW K1200RS Electronic Cruise Control installation instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
We recommend that you take power from a non-critical circuit such as the heated grip circuit. Any power supply wire that is green with a black trace (stripe) is a fused, switched 12V supply. That is, there is a fuse in the line, and the ignition switch turns the power to the wire on and off, and it is NOT powered when the ignition switch is in the ‘park’ position (side lights turned on). Because the ignition switch also powers the ABS system, if the heated grip circuit is live, in theory the ABS system, and therefore the brake light system, will also be live. • On the bikes that we have fitted the cruise control to, there is a three way plug behind the headlight, that goes to the heated hand grip switch (on the right side handlebar). This plug has one green/black wire, a black wire and an orange wire. This photo is taken looking down below the bike’s instruments on the right side. The plug is circled. • This photo is taken from the front of the bike looking back through the head light cavity, under the bikes instruments. The plug is circled. • This is a convenient and accessible location to pick up power for the cruise control. The cruise control orange power wire should be connected to the green/black power wire for the heated grips.

2003-2004 HONDA GL 1800/A Frame Weld Safety Recall

0

Filed Under (Honda) by admin on 15-12-2010

download
there is no punch mark on the VIN plate as specified in this Service Bulletin, proceed to the REPAIR PROCEDURE section of this Service Bulletin. IMPORTANT: Due to the complexity of this campaign it is imperative that you check iN and your Dealer Responsibility Report before you begin repairs. If iN or your Dealer Responsibility Report indicate the Safety Recall has been performed, but you confirm the unit is not punched and the repair has actually been done (by inspecting the weld), please contact the Warranty HelpLine at (800) 421-1900, option 7. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510)  Frame Weld Inspection Chart (S0516) You MUST provide your TIG welder with the following items:  2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511)  2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) Welding Template Box (S0512) All of the above items were shipped to you with Service Bulletin GL1800 #14. If you need additional copies of these materials, you may order them from Resolve at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. DISASSEMBLY OVERVIEW You will be removing the following components from the vehicle as instructed in the Dealer Booklet : Handlebar weights Rear view mirrors Swingarm pivot covers Rider foot pegs Seat Side covers/Engine side covers Fairing pockets Fairing molding Meter panel Top shelter Battery Fuel tank Main wiring harness ground Front lower fairing Front exhaust pipe protector Muffler/exhaust pipe Antenna Whip(s) Coolant reserve tank Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: Before you send the motorcycle to the welder, you MUST check for lower crossmember frame weld cracks.  If your inspection reveals no cracks in or on either the Left or Right lower cross- member frame welds, proceed to the REPAIR PROCEDURE OVERVIEW section of this Service Bulletin.  If your inspection identifies a crack or cracks in or on either the Left or Right lower crossmember frame welds, perform the following procedure: Place the grinding template (S0512) on the crossmember. Using a suitable felt marker, draw a line on the weld with the crack, drawing the line along the entire edge of the the template (this line will be 89 mm long). If the crack falls within the length of this line (89 mm) , prepare the motorcycle for welding per the Dealer Procedures and advise the welder to use the Cracked Weld Repair Manual (S0515). After the bike has returned from the welder, prepare the frame and re-assemble the motorcycle per the Dealer Procedures . Then, proceed

Incoming search terms:

KAWASAKI Z1000 GTR Electronic Cruise Control Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The dual spool and carburettor cable are installed. The carburettor cable is attached to the lower groove in the dual spool. The other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable affects the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in the carburettor cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also affects the apparent free play in the carburettor cable

Incoming search terms:

BMW K1100 RS/ RT/ LT ABS 2 Electronic Cruise Control Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
The actuator spool is installed in the CIU housing with the actuator cable. The actuator spool is rotated to fully extend the cable. 2nd step. The carburettor cable and spool are installed and the other end of the carburettor cable is attached to the carburettors. Note the position of the roll pin. It is nearly contacting the end of the groove in the actuator spool. The free play in the carburettor cable must be adjusted so that the cable outer can be pulled out 2 ~ 3mm before the carburettors start to open. This ensures that the cruise control cannot prevent the carburettors returning to idle. If more free play is allowed the response of the cruise control is compromised. This adjustment of free play is usually performed after final assembly of the CIU is completed and the CIU is in its final location. This is because flexing the cable does effect the free play. It is shown at this stage in these diagrams to improve clarity. After this adjustment is performed, the carburettor cable adjustment MUST NOT BE MOVED. All future adjustments of free play in the throttle must be performed on the throttle cable from the throttle grip. If incorrect free play in this cable is suspected due to inconsistent cruise operation or because of inconsistent idle speed, the adjusters on the throttle cable from the hand grip must be backed all the way off to give as much free play as possible. If this does not result in AT LEAST 5mm of free play in the throttle cable, the throttle cable must be removed from the hand grip or CIU before adjustment of the carburettor cable is attempted. This is crucial because the amount of free play in the throttle cable also effects the apparent free play in the carburettor cable.

SUZUKI SV1000S EMISSION CONTROL INFORMATION/ SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
EMISSION CONTROL SYSTEMS FUEL INJECTION SYSTEM SV1000S motorcycles are equipped with a fuel injection system for emission level control. This fuel injection system is precision designed, manufactured and adjusted to comply with the applicable emission limits. BEFORE-PRESSURIZED FUEL PRESSURIZED FUEL * I’ RELIEVED FUEL ~%~~~ Ift 0 0 9 0 0 0 EMISSION CONTROL INFORMATION 9-3 CRANKCASE EMISSION CONTROL SYSTEM The engine is equipped with a PCV system . Blow-by gas in the engine is constantly drawn into the crankcase, which is returned to the combustion chamber through the breather hose, air cleaner and throttle body . C * FRESH AIR FUEL/AIR MIXTURE 411111110 BLOW-BY GAS 9-4 EMISSION CONTROL INFORMATION EXHAUST EMISSION CONTROL SYSTEM (PAIR SYSTEM) The exhaust emission control system is composed of the PAIR system and THREE-WAY CATALYST system. The fresh air is drawn into the exhaust port with the PAIR solenoid valve and PAIR reed valve . The PAIR solenoid valve is operated by the ECM, and the fresh air flow is controlled according to the TPS, ECTS, IATS, ZAPS and CKPS. H02 sensor (Except for USA) I 0 0 0 0 0 NOISE EMISSION CONTROL SYSTEM TAMPERING WITH THE NOISE CONTROL SYSTEM PROHIBITED : Federal law prohibits the following acts or the causing thereof: 1. The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or 2. The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW : • * Removing or puncturing the muffler, baffles, header pipes, screen type spark arrester (if equipped) or any other component which conducts exhaust gases . • * Removing or puncturing the air cleaner case, air cleaner cover, baffles or any other component which conducts intake air . • * Replacing the exhaust system or muffler with a system or muffler not marked with the same model specific code as the code listed on the Motorcycle Noise Emission Control Information label . EVAPORATIVE EMISSION CONTROL SYSTEM (FOR E-33)

Incoming search terms:

Incoming search terms: