where do the radiator pipes on a kx 85

You search Auto repair manual PDF where do the radiator pipes on a kx 85, if there are search results will appear below. If search results do not exist, please search by others keyword.



  where do the radiator pipes on a kx 85 Direct Download speed 5282 Kb/s

  where do the radiator pipes on a kx 85 Full Version speed 6162 Kb/s



2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

Cobra JR/ OI Radiator with Louvers Replacement

0

Filed Under (Cobra) by admin on 10-11-2010

download
The 2009 model year radiator for Cobra JR (also remaining OI ) model will be FCCJ0004 which now has provisions for louvers. On the 2009 models these louvers also rely on a feature on the frame down-tube for mounting the plastic louvers. Older models do not have these features on the frame and so it is not possible to utilize the louver mounts on the radiator. Customers with older models JR/CM or OI/P3/PW3 needing a replacement radiator for ECMU0061 or ECMU0225 will be sold a radiator kit FKMU0001 which includes the new style radiator, FCCJ0004C (with louver mounting tabs removed), and all mounting hardware. This will allow the mounting of the new style radiator onto these products without mounting the louvers. As the 2009 frame is now the service replacement frame for JR/CM & OI/PW3/P3 models from 2004 – 2008, the louvers are able to mount on all older models JR/CM & OI/PW3/P3 that have the appropriate mounting provisions. Welding on the highly stressed down-tube frame member is not recommended by Cobra because it can cause premature structural failure to the frame and possible injury to the rider.

Suzuki SV1000 COOLING AND LUBRICATION SYSTEM REPAIR MANUAL

0

Filed Under (Suzuki) by admin on 25-02-2011

download
At the time of manufacture, the cooling system is filled with a 50 :50 mixture of distilled water and ethylene glycol anti-freeze . This 50:50 mixture will provide the optimum corrosion protection and excellent heat protection, and will protect the cooling system from freezing at temperatures above -31 °C (-24 °F) . If the motorcycle is to be exposed to temperatures below -31 °C (-24 °F), this mixing ratio should be increased up to 55 % or 60 % according to the figure. CAUTION • Use a high quality ethylene glycol base anti-freeze, mixed with distilled water . Do not mix an alcohol base anti-freeze and different brands of anti-freeze. • Do not rut in more than 60%anti-freeze or less than 50 %. (Refer to the right figure.) • * Do not use a radiator anti-leak additive. A WARNING COOLING AND LUBRICATION SYSTEM 5-3 20 40 60 80100 0 10 20 30 40 50 60 Density (%) Fig .2 Engine coolant density-boiling point curve • * You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot . After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off . • * The engine must be cool before servicing the cooling system . • * Coolant is farmful; • * If the comes in contact with skin or eyes, flush with water. • * If swallowed accidentally, induce vomiting and call physician immediately . • * Keep it away from children . Anti-freeze density Freezing point 50% -31 °C (-24 °F) 55% -40 °C (-40 °F) 60% -55 °C (-67 °F) 50 % engine coolant including reservoir tank capacity Anti-freeze 1 100 ml (2.3/1 .9 US/Imp-pt) Water 1 100 ml (2.3/1.9 US/Imp.pt) Density (%) Fig.1 Engine coolant density-freezing point curve (°F) (°C) 302 150 (kgf/cm2) 284 140 1.5 c Q 266 130 0.9 0) a) :0 248 120 0.5 0) m Z3 230 110 0 (7 212 100 (F) (C) 32 0 14 -10 -4 -20 C 0 Q -22 -30 O) C N -40 -40 a) a) U- -58 -50 -76 -60 -94 -70 5-4 COOLING AND LUBRICATION SYSTEM COOLING CIRCUIT THERMOSTAT RESERVOIR TANK RADIATOR NO. 1 CYLINDER HEAD NO . 1 CYLINDER NO. 2 CYLINDER NO. 2 CYLINDER HEAD WATER PUMP INSPECTION Before removing the radiator and draining engine coolant, inspect the cooling circuit for tightness. • * Remove the body cowling. (=6-6) • * Remove the radiator cap ® . • * Connect the tester 02 to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 110 kPa (1.1 kgf/cm 2, 15 .6 psi) and see if the system holds this pressure for 10 seconds. • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system. In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed the radiator cap release pressure, or the radiator can be damaged

Kawasaki 2000- ZX-12R Ninja exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1, 2, 3, and 4 by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. Place a billet aluminum Mouthpiece ring Z on each TiForce head pipe. (see figure 3 for details) . 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the head pipes fit flush and snug in the ports and Mouthpiece ring Z before tightening. 7. Install the S-Bend to the front section of the head pipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes and Mouthpiece ring Z are centered in each port. 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. (See figure 1) . 11. Place the bands approximately 118 mm from the edge of the end can. (See figure 2) . 12. Using the stock provided mounting point on the passenger foot peg, and using the stock-mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance

HONDA VTX 1800 CHROME RADIATOR COVER INSTALLATION

0

Filed Under (Honda) by admin on 29-12-2010

download
Remove the amber reflectors from the sides of the stock plastic radiator cover. These can be pried off carefully using a wide screwdriver blade or small putty knife. 2. Remove the 3 allen screws from the stock plastic radiator cover, 2 on top and 1 on the bottom. 3. Slide the chrome radiator cover over the stock plastic cover. 4. Re-Install the two original upper screws into the top holes. In the bottom hole install the button head allen screw and washer provided. Tighten all three screws. Firmly press the reflectors back onto the chrome cover

HONDA VTX1300 RADIATOR COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

downoad
1. Remove the upper radiator cover bolts. 2. Hook on lower edge of chrome cover over existing radiator cover. 3. Align upper holes with existing holes. 4. Replace bolts

2007 Kawasaki ZX6R Full System Installation

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
1. Remove the faring lowers (save STD bolts for reuse) , side faring (save STD bolts for reuse) , seat faring (save front 2 STD bolts for reuse) and right silencer cover. 2. Detach the turn signal assy, (unplug the cable coupler of turn signal and brake light at the same time) 3. Remove the radiator under bracket and lightly unscrew the radiator mounting bolt. Move the radiator forward. This will make you to have enough room for detaching exhaust pipes and flange nuts. Then, take off the standard headpipes. Detach the cable of the exhaust device and l eave servomotor stayed in the motorbody. (save (3) STD bolt and nut and (8) flange nuts for reuse) 4. Assemble the enclosed head pipes 1,2,3 and 4 by matching the 4-2-1 joint. Do not install the exhaust springs at this time. Lightly attach the assembled head pipe sections to the exhaust ports. Make sure the ends of the head pipes fit snug in the ports. 5. Install the tail joint and tail pipe to the joints. Do not install the exhaust springs yet. Jiggle the whole assemble for better fitting. Lightly attach the tail pipe by standard bolt and nut saved in step 3, but do not tighten the bolt fully. (see Image 1) *Recommend to use new gasket to prevent from leaking the exhaust. *Lightly screw the (8) STD flange nuts saved in step 3. * Cylinder number is 1, 2, 3 and 4 from the left hand side with you on the motorbike. 6. Attach enclosed silencer stay A to the place where the standard silencer mounted by (2) STD bolts and nuts saved in step 3. Reinstall the seat faring and penetrate the (2) 5x45mm to the hole of a seat faring mounted. Fix the Silencer stay A by enclosed (2) M5 nuts and (2) aluminum collar using the thread of penetrated M5x45bolts. (see Image 2 and drawing 1) Image 2 7. Insert the TiForce silencer to the tail pipe. Put silencer band and band rubber to the assembled silencer stay A by enclosed (2) M8x20mm bolt and (2) M8 washer. (see drawing 1) 8. Attach the supplied springs to all the joints. Use a spring puller to prevent damage to the springs that could lead to future failure. Put the radiator back to the original position. 9. Attach the L and R license number stay to the silencer stay A. (see Image 3) (see drawing 1) 10. Reinstall the firings detached in step 1. Attach the right silencer cover to the frame by using enclosed faring stay and (1) M6x20mm. (see drawing 1) 11. Make sure the exhaust system is free and clear of the faring. If necessary, adjust for proper clearance.. Removed the fairings reinstalled in step 10. 12. Securely tighten all fasteners in this order (from exhaust pipe flange to silencer stay) Image 3 14. Attach the turn signal assy detached in step 2 to the license number stay. (Use (4) M6x15mm) (See Image 4) Plug the cable couplers.

Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms:

HARLEY DAVIDSON V-ROD Fi2000 Fuel Injection Module Installation Manual

0

Filed Under (Harley Davidson) by admin on 15-11-2010

download
1. Flip up seat, to gain access to radiator reservoir area. 2. Remove Dzus fastener to remove simulated fuel tank cover, over airbox housing. Depending on which model V-Rod is being worked on, the front shrouds covering the upper front frame section may also need to be removed. 3. Place Fi2000 in under-seat area, run fuel injector connector harness up right side frame rail between top right frame rail, and radiator overflow tank, see Figure 1. At the rear of the airbox, route the harness below the airbox, and downward next to the inner radiator hose. Unplug both stock fuel injector connectors, on the front and rear injectors between the engine cylinders, see Figure 2. These are disconnected, by depressing the metal springs that are on the end of each female connector. The stock female connectors are marked “F” and “R”, noting which connector goes to the front and rear injector, be sure to pay attention to this. Now connect the longer male Fi2000 connector to the front female H.D. connector. Plug shorter Fi2000 male connector into the stock rear female H.D. connector. Then plug the longer female Cobra connector onto the front stock H.D. injector. Plug the shorter Fi2000 female connector onto the rear injector. Each injector connector pair should rest underneath each respective injector. 4. It is now time to install the oxygen sensor eliminator modules. This product is designed to eliminate the “check engine” light from coming on when the stock oxygen sensors are disconnected on Harley Davidson Motorcycles utilizing fuel injection. The motorcycle has a full “open loop” fuel injection map written in its ECU and the motorcycle reverts to this default map after the oxygen sensors have been removed or just disconnected. 5. Locate the rear oxygen sensor and follow the harness up to the under-seat area behind the radiator overflow tank. Pull the stock connectors up from below the overflow tank and disconnect, see Figure 1. Plug one of the supplied Oxygen sensor eliminators on to the stock male connector. Tuck the connectors back underneath the bracket behind the radiator overflow tank. 6. Now locate the front oxygen sensor on the front headpipe, and trace the oxygen sensor harness back to the connectors tucked between the left front frame rail and plastic radiator shroud, see Figure 3. Pull these connectors out, and disconnect them. Plug the remaining supplied oxygen sensor eliminator on to the stock male connector. Tuck the connectors back in between the frame rail and plastic shroud

1990- 1995 TOYOTA 4RUNNER BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

Download
Disconnect both battery cables. Disconnect negative cable first, then positive cable Disconnect and move radiator out of the way. . Remove overflow hose from radiator spout. b. Remove four bolts securing radiator to core sup-port. c. Lift radiator up out of slots in core support. d. Straighten tabs on radiator. e. Lay radiator on fan while lifting body. 3. Relocate alternator ground strap if equipped Adhere to recommendations when replacement fasten-
ers, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper
retention characteristics. This system may not include all replacement hardware as recommended by the fac-
tory service manual. Additional replacement hardware should be obtained prior to installation of this system to
meet the requirements of the factory service manual.

Incoming search terms: