where does the breather on a vmax

You search Auto repair manual PDF where does the breather on a vmax, if there are search results will appear below. If search results do not exist, please search by others keyword.



  where does the breather on a vmax Direct Download speed 5282 Kb/s

  where does the breather on a vmax Full Version speed 6162 Kb/s



HARLEY DAVIDSON EFI INTAKE MANIFOLD COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 1. Remove screw (A) that holds the air cleaner cover (B) and seal (C). 2. Remove three T27 TORX® screws (D) to release the cover bracket (E) from the filter element (F). 3. Remove the filter element, pulling the two breather tubes (G) from hole on the inboard side of element. 4. Remove the two breather tubes (G) from the fittings on the two cylinder head breather bolts (I). 5. Remove the two breather bolts (I) and O-ring seals (K) from the air cleaner backplate (J) with a 7/16 inch deepwell socket. 6. Remove the backplate and gasket (H) from the injection module. 7. Aligning the flat edge of a new cover gasket (2) with the backplate molded tab, install a gasket (2), chrome cover (1) and second gasket, in order, on the air cleaner back- plate. 8. Install the breather bolts through the air cleaner backplate. Re-install O-ring seals onto each breather bolt. Install a washer (3) from the kit on each breather bolt. Apply Loctite 243 to the breather bolts and align holes in the backplate with the holes in the cylinder heads and install the breather bolts. Use a 7/16 inch deepwell socket and alternately tighten the breather bolts to 120-144 in-lbs (13.6-16.3 Nm) . 9. Slide gasket over the sleeve on the inboard side of filter element. 10. Install breather tubes about 1/4 inch (6.4 mm) into holes on inboard side of filter element. 11. Install breather tubes onto fittings of two cylinder head breather bolts. NOTE Air cleaner mounting without installation of the breather tubes allows crankcase vapors to be vented into atmosphere in violation of legal emissions standards. 12. Place the filter element onto backplate, with the flat side down, so that the hole on the inboard side of element fits over the molded boss in the backplate. 13. Align holes in cover bracket with those in filter element and start three screws. Stamp on cover bracket points downwards. Use a T27 TORX drive head, alternately tighten screws to 20-40 in-lbs (2.3-4.5 Nm) . 14. Make sure that the rubber seal is proper seated around perimeter of air cleaner cover and place cover on back- plate. 15. Fit the air cleaner cover onto backplate. Apply Loctite 243 to the threads of air cleaner cover screw. Install screw through cover and tighten to 36-60 in-lbs (4.1-6.8 Nm)

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) Original Equipment (OE) Air Cleaner Removal For carbureted models: Refer to the service manual and check the warm-slow idle speed adjustment before removing the OE air cleaner backplate. For EFI (fuel-injected) models: Have a Harley-Davidson dealer recalibrate the ECM prior to air cleaner installation. 2. Remove the air cleaner backplate following the instructions in the service manual. Retain the two breather screws (A) removed from the backplate (see Figure 1). The remaining parts can be discarded. 3. See Figure 1. Remove and discard induction module bracket (B). “Heavy Breather” Air Cleaner Installation NOTE When servicing the air cleaner, apply Loctite 243 (blue) to all threaded fasteners (both male and female threads). 4. Install the new O-rings (4) in the grooves around the breather screw holes on the carburetor or induction module side of the backplate (1 or 2)

Incoming search terms:

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

2007 Yamaha VMAX/ VMX12W1(C) OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
GASOLINE IS HIGHLY FLAMMA- BLE: * Always turn the engine off when refueling. * Take care not to spill any gasoline on the engine or exhaust system when refueling. * Never refuel while smoking or in the vicinity of an open flame. * Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. * Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: * The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. * Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. * Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. * When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the carburetor or fuel tank. * If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

HARLEY DAVIDSON SCREAMIN' EAGLE VENTILATOR PERFORMANCE AIR CLEANER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove the main fuse. Refer to the service manual. 2. Remove the existing air cleaner backplate. Refer to the service manual. Save the original equipment (OE) button head screw that secures the air cleaner cover. Discard the remaining parts. 3. Remove the fuel tank. Refer to the service manual. 4. See Figure 1. Remove and discard the induction module support bracket. is05912 Figure 1. Remove Induction Module Support Bracket INSTALLATION Air Cleaner Installation Use only supplied air cleaner cover. Use of another air cleaner cover could cause element failure and detachment of the air cleaner cover, which could distract the rider and result in death or serious injury. (00596b) NOTE When servicing the air cleaner, apply Loctite 243 – Blue to the threads of all fasteners. 1. See Figure 3. Install two O-rings (1) from the kit in the grooves around the breather bolt holes on the induction module side of the backplate assembly (2). Install the remaining two O-rings in the grooves in the underside of the heads of the breather bolts (5). 2. Remove the liner from the adhesive backing of the gasket (3). Carefully position the adhesive side of the gasket to the backplate, aligning to the equally spaced screw holes, and press the gasket firmly into place. 3. Insert new breather bolts (5) through the backplate. 4. Apply Loctite 243 – Blue to the breather bolt threads and the mating tapped holes in the cylinder head. 5. Thread the bolts into the cylinder head, but do not tighten. 6. Thread the air cleaner mounting studs (4) all the way through the backplate (2) until the screw threads are captured in the induction module. Do not tighten completely at this time. 7. Alternately tighten the two breather bolts to 120-144 in- lbs (13.6-16.3 Nm) . 8. Tighten the three air cleaner studs to 55-60 in-lbs (6.2- 6.8 Nm) . 9. Install the fuel tank. Air Cleaner Element and Cover Installation

HARLEY DAVIDSON DECORATIVE TRIM FOR HEAVY BREATHER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION NOTES To avoid exposure to grease, oil, dust, dirt and skin oil, do not remove the backing film from the medallion or medallion insert until the moment of application. For maximum adhesive bond, the intake tube surface under and immediately surrounding the medallion must be clean and dry. 1. Clean the surface of the intake tube with a mixture of 50- 70 percent isopropyl alcohol and 50-30 percent distilled water. Allow to dry thoroughly. NOTE Ambient temperature should be 70-100 °F (21-38 °C). 2. See Figure 1. Remove backing film from medallion insert (1) and install on medallion (2). 3. With the backing film still in place, trial fit the medallion (2) to the intake tube. 4. Remove the backing film from the back of the medallion. Press the medallion firmly into position for about five sec- onds. 5. After releasing pressure, avoid direct contact with the medallion for at least 20 minutes. NOTE Allow AT LEAST 24 hours before exposing the air cleaner to vigorous washing, strong water spray or extreme weather. The adhesive bond will increase to maximum strength after about 72 hours at normal room temperature

DRAK AIR FILTER KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
1. Take off the Air fi lter cover by removing the Button head cap screw in the center. 2. Removed the fi lter element by taking out the three exposed Torx head cap screws. 3. Remove the breather hoses from the Cylinder head breather bolts by pulling on them. 4. Remove the three Bolts that secure the Backing plate to the Carburetor / Throttle body and the two Breather bolts that secure it to the Cylinder heads. 5. Remove the Backing plate and Gasket, on FI models the wiring mount clip should be carefully pulled out of the plastic housing. NOTE: Be sure that the gasket surface is clean and dry and that no gasket material remains stuck to it. 6. None of the OEM parts will be reused for this installation 1. For a clear understanding of this installation it is best to refer to the exploded view diagram while reading these instructions. 2. When installing or servicing the air cleaner, apply Loctite 243 (blue) to threads of all fasteners. 3. Loosely install the gasket (1) and carburetor / throttle body mount bracket (2) using the two cylinder head breather bolts (3) and cylinder head O-rings (4) NOTE: Make sure the gasket is installed in the correct rotation and right side up. The slightly smaller bleed hole should be in the top left hand corner. 4. Using the three 1/4″-20 x 1″ socket head cap screws (5) install the fi lter backing

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

YAMAHA PW50 (X) OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
Before operating the motorcycle: * Check the fuel tank breather hose connection. * Check the fuel tank breather hose for cracks or damage, and replace it if damaged. * Make sure that the fuel tank breather hose is not blocked, and clean it if necessary. EAU13452 2-stroke engine oil Make sure that there is sufficient 2-stroke engine oil in the oil tank. Add the recommended 2-stroke engine oil as necessary. NOTE: Make sure that the 2-stroke engine oil tank cap is properly installed. EAU40701 Fuel cock The fuel cock supplies fuel from the tank to the carburetor while filtering it al- so. The fuel cock has two positions: S (stop) With the lever in this position, fuel will not flow. Always return the lever to this position when the engine is not running. 1. Fuel tank breather hose 1 1. 2-stroke engine oil tank cap 2. Minimum level mark Recommended oil: See page 8-1. Oil quantity: 0.30 L (0.32 US qt) (0.26 Imp.qt) 2 1 1. Arrow mark pointing to “S” (stop) 1
INSTRUMENT AND CONTROL FUNCTIONS 3-6 1 2 3 4 5 6 7 8 9 O (on) With the lever in this position, fuel flows to the carburetor. Normal riding is done with the lever in this position. EAU13590 Starter (choke) lever “” Starting a cold engine requires a richer air-fuel mixture, which is supplied by the starter (choke). Move the lever in direction (a) to turn on the starter (choke). Move the lever in direction (b) to turn off the starter (choke). EAU13680 Kickstarter To start the engine, fold out the kick- starter lever, move it down lightly with your foot until the gears engage, and then push it down smoothly but force- fully

S&S Super E and G Series "Shorty" Carburetors REMOVAL, Installation and Jetting Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
Remove Old Carburetor WARNINGS ● Gasoline is extremely flammable and explosive under certain conditions. Do not smoke around gasoline. Gasoline fumes are toxic when inhaled. Perform installation in a well ventilated area away from open flames or sparks. Any gasoline leak or spill constitutes a health and fire hazard. ● If motorcycle has been running, wait until engine and exhaust have cooled to avoid getting burned during installation. ● Electrical sparks can ignite explosive gasoline fumes. Failure to disconnect battery while working on motorcycle can also result in inadvertent engagement of starter and personal injury. A. Shut off fuel petcock and disconnect battery. B. Remove air cleaner assembly. Drain fuel from existing carburetor. Remove carburetor, manifold, choke cable and any carburetor mounting hardware NOTE – Removing and tightening hard to reach Allen bolts such as carb-manifold mounting bolts and V2 manifold flange bolts can be greatly simplified by the use of Allen ball-end drivers. These tools are available at most automotive and tool supply houses. See Picture 9. Additionally, Performance Plus of Evansville, Indiana, produces a hex wrench specially modified for accessibility of V 2 manifold bolts. Call 812-963-8854 for further information. As alternative, standard hex wrench can be shortened for convenience. NOTE – Some Buell motorcycles have a breather fitting with 90° elbow on rear head. Due to proximity of frame, elbow must be removed before fitting can be taken off engine. Loosen fitting and rotate to position convenient for cutting elbow. Secure fitting by tightening against cylinder head. Elbow may be inaccessible to hacksaw. In most instances, a die grinder with cutoff wheel will remove elbow with little difficulty. If die grinder is unavailable, grasp elbow firmly with pliers and snap off, then remove fitting. CAUTION – Extreme care must be taken to prevent metal chips from entering engine when elbow is removed. S&S recommends packing breather fitting with gease before removing elbow. Metal chips inside engine will cause extensive damage. Installer bears all responsibility for containment of chips and other debris. Picture 2 Picture 4 Picture 3
5 2. Prepare Air Cleaner Backplate NOTE – Fast idle lever screws, part #11-2384, must not be overtightened. Loctite or other thread locking compound may be used sparingly on threads to prevent screws from vibrating loose. CAUTION – Overtightening fast idle screws may damage backplate. A. All engines except V2s 1. Knuckles & Pans, 1936 to 1965 – Press plugs, part #50-8312, into holes in air cleaner backplate. See Picture 2 . 2. Shovels, 1966 to 1979, and Ironhead (IH) XLs, 1957 to 1979 – Press plug, part #50-8312, into hole in air cleaner backplate. See Picture 3 . 3. Shovels 1980 to 1984 and IH XLs 1980 to 1985 – Screw crankcase breather vent elbow fitting, part #50-8110, into hole in air cleaner backplate and angle downward as shown in Picture 4 . On 1983 and 1984 Shovels press plug, part #50-8312, into other hole on left. 4. Assemble fast idle mechanism as shown in Figure A . B. FL V2s 1984 to 1992 1. Press plug, part #50-8312, into hole on left in air cleaner backplate as shown in Picture 5 . 2. Screw vent hose elbow fitting, part #50-8110, into remaining hole at right. See Picture 5 . 3. Assemble fast idle mechanism as shown in Figure A . C. XL V2s 1986 to 1990 1. Press plug, part #50-8312, into hole on right in air cleaner backplate as shown in Picture 6 . 2. Screw vent hose nipple fitting, part #50-8111, into remaining hole at left. See Picture 6 . Elbow fitting, part #50-8110, supplied in kit may also be used in this location if required. 3. Assemble fast idle mechanism as shown in Figure A . D. FL V2s 1993 and up and XL V2s 1991 and up 1. Press plugs, part #50-8312, into both holes in air cleaner backplate as shown in Picture 7 . 2. Assemble fast idle mechanism as shown in Figure A . E. Buell motorcycles, 1994 and up 1. Assemble fast idle mechanism as shown in Figure A. 3. Throttle Preparation NOTE – Throttle grip assembly must be assembled correctly and work freely to prevent possible sticking during operation. Throttle must snap closed when released. Cable routing must be free of tight bends to minimize friction between cable and housing

Incoming search terms: