where is the fuse located for the cooling fan on a 2002 honda vtx 1800r

You search Auto repair manual PDF where is the fuse located for the cooling fan on a 2002 honda vtx 1800r, if there are search results will appear below. If search results do not exist, please search by others keyword.



  where is the fuse located for the cooling fan on a 2002 honda vtx 1800r Direct Download speed 5282 Kb/s

  where is the fuse located for the cooling fan on a 2002 honda vtx 1800r Full Version speed 6162 Kb/s



2003 SUZUKI SV 650 COOLING AND LUBRICATION SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COOLING CIRCUIT INSPECTION Before removing the radiator and draining the engine coolant, inspect the cooling circuit for tightness. • * Remove the cowling. (SV650S) (C-7–7-6) • * Loosen the radiator cap stop screw 10 . (SV650) • * Remove the radiator cap O2 and connect the radiator tester to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 120 kPa (1 .2 kgf/cm2,17.0 psi) and see if the system holds this pressure for 10 seconds . • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system . In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed specified pressure, or the radiator can be damaged. COOLING AND LUBRICATION SYSTEM 6-3 6-4COOLING AND LUBRICATION SYSTEM RADIATOR REMOVAL • * Remove the cowling. (SV650S) ( r- 7-7-6) • * Drain engine coolant. (r– 72-20) • * Disconnect the right and left radiator hoses from the radiator. • * Disconnect the siphon hose from the radiator. • * Disconnect the horn lead wires. rI .rr • * Remove the radiator lower mounting bolt. • * Disconnect the cooling fan motor and its thermo-switch lead wire coupler 10. • * Remove the radiator by upper mounting bolt. • * Remove the cooling fan. • * Disconnect the cooling fan thermo-switch. • * Remove the cooling fan thermo-switch. • * Remove the horn. CAUTION When removing the horn, hold the nut by spanner to prevent the horn bracket distortion. COOLING AND LUBRICATION SYSTEM 6-5 INSTALLATION • * Install the cooling fan and horn. 0 Cooling fan/horn mounting bolt: 8 N .m (0.8 kgf-m, 6 .0 Ib-ft) • * Install the cooling fan thermo-switch. ( l”76-9) • * Install the siphon hose to the radiator. • * Install the radiator in the reverse order of removal. • * Route the radiator hoses properly. (=9-22) 9-22) • * Install the drain plug with a new sealing washer and pour engine coolant. (=2-20) • * Bleed air from the cooling circuit. (r– 72-21) • * Install the cowling. (SV650S)

Incoming search terms:

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

Incoming search terms:

HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

Incoming search terms:

HONDA VTX DESTINATIONS FUEL SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 10-02-2012

download
WHY CHOOSE A VTX? Riders have always chosen Hondas because they want to ride. Really ride. They like the performance. The reliability. The build quality. They know that a Honda is a bike you can rely on for decades, and thousands of miles. Our 2008 Honda VTX® cruisers still offer all that. But along the way, we’ve added another feature: drop-dead-gorgeous good looks. It used to be you had to choose between performance and style. Between reliability and looks. But with a Honda VTX, you can have it all. Maybe you’re content to trailer your bike places, or to just ride it ten minutes at a time and then get off and pose. Hey, whatever turns your crank—it’s your life. But when you want to actually ride, well, then there’s only one choice

Incoming search terms:

2002 Honda VTX 1800 R & S 3” BIG Straights Installation Instructions

0

Filed Under (Honda) by admin on 17-11-2011

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation
NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to
replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design,
configuration and location. WARNING: Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessaryon a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed

Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

Incoming search terms:

2002-2003 Honda GL1800/ A Frame Weld REPAIR PROCEDURE OVERVIEW

0

Filed Under (Honda) by admin on 14-12-2010

download
If your inspection identifies a crack or cracks in or on either Left or Right lower crossmember frame welds, STOP – call your DSM or TechLine for further instructions. • If your inspection reveals no cracks, proceed to REPAIR PROCEDURE. NOTE: Verification of repair can also be found in the Dealer Responsibility Report and on the Honda Interactive Network (iN). If you have any questions about verification, please contact TechLine before proceeding. IMPORTANT: For complete Dealer and Welder Repair procedures, refer to the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Booklet (S0510) • Frame Weld Inspection Chart (S0513) You MUST provide your TIG welder with the following items: • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • Welding Template Box (S0512) All of the above items were shipped to you with this Service Bulletin. If you need additional copies of the Dealer Booklet , Welding Manual , Welding Template Box , or Frame Weld Inspection Chart , you may order them at no cost from DDS at (440) 572-0725. For your reference, a brief repair procedure overview is provided below. Disassembly Overview You will be removing the following components from the vehicle as instructed in the Dealer Booklet : • Handlebar weights • Rear view mirrors • Swingarm pivot covers • Rider foot pegs • Seat • Side covers/Engine side covers • Fairing pockets • Fairing molding • Meter panel • Top shelter • Battery • Fuel tank • Main wiring harness ground • Front lower fairing • Front exhaust pipe protector • Muffler/exhaust pipe • Antenna Whip(s) • Coolant reserve tank • Center stand NOTE: You will need to remove any accessories that may contact the ground during the Welding and Re-assembly procedures. IMPORTANT: You MUST cover the following with RED duct tape for welder identification pur- poses: • Negative (-) and positive (+) battery cables • Fuel return hose end • Fuel feed hose end • Main wiring harness ground • Alternator • Exhaust ports Welding Overview A qualified TIG welder will weld the frame following the procedures in the 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual . Re-assembly Overview You will be inspecting the new TIG welds, painting the frame, and re-assembling the vehicle as detailed in the Dealer Booklet and Frame Weld Inspection Chart (S0513)

Incoming search terms:

2001 – 2002 GL1800/ GL1800A Rear Tire Inspection

0

Filed Under (Honda) by admin on 27-11-2010

download
1. Inspect the motorcycle for a punch mark as described in Identification on page 2. If a punch mark is present no further action is necessary, return the unit to the customer. 2. Qualify the unit/customer as follows: •Is the tire on the motorcycle the original factory installed tire? •Is the air pressure loss more than three psi per month? Note: Refer to page 145 in the Owner’s Manual. “Even tires that are in good condition may lose one to two psi per month if not checked and adjusted regularly” . If the GL1800 meets the above qualifications, proceed with the repair procedure. 3. Place the motorcycle on a lift and secure it on the centerstand. 4. Remove the rear wheel as described on page 14-9 of the Service Manual. 5. Starting at the valve stem/balance mark area, carefully remove the rear tire from the wheel. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. 6. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 2001 – 2002 GL1800/GL1800A Rear Tire Inspection GL1800 #6 OCTOBER 2001 MTB 9430 (0109) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-ityourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800/GL1800A Rear Tire Inspection 0110 GL1800 #6*GL1800 #6*0110*2001-2002 GL1800/GL1800A Rear Tire Inspection*GL1800/GL1800A, Rear Tire Inspection, Bead, Tread*Motorcycle*1800 2 of 4 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #6 OCTOBER 2001 Inside BeadInjury Outside BeadInjury Outside BeadInjury 7. Carefully inspect the entire circumference of both tire beads. Inspect both the inside and outside of the bead for any distortion or injuries. See examples of injuries below. 8. If there is no evidence of bead damage, re-install the tire on the rim. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Be sure to align the balance dot with the valve stem. Inflate the tire to 41 psi. Install the wheel assembly on the motorcycle and proceed to the Identification and then to the Warranty section. 9. If any damage or injury is present replace the tire and valve stem. Be sure to use plenty of commercially available tire lubricant on the inside and outside of both beads. Balance the new tire as necessary

Incoming search terms:

HONDA VTX 1800 AIR HORNS AHVTX INSTALATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns. Cut a new piece of hose 2 ¾” long, replace the old short hose on the “Y” with this. Re-install the “Y” hose assembly onto the horns with the short hose on the long trumpet, route the hoses behind the horns and connect the long hose to the short horn (see photo 2A). 4. Remove the upper 8mm (12mm wrench size) motor mount bolt (see photo 2B). Install the horn assembly using the 8 x 55mm bolt and spacer tube provided. If the motorcycle is fitted with Honda line tubular radiator or engine guards the above mounting will not work. You will need instead to locate the “J” shaped bracket and small hose clamp provided in the hardware kit (see photo 2 on instructions of multi -application instruction sheet). Thread the hose clamp thru the bracket and attach to the frame or Honda line guards as shown ( see photos 2&3 ) tighten the hose clamp securely using a socket or wrench. Attach the horn set to the “J” bracket using the 5/16 x ¾” bolt, nut and lock washer provided. Position the horns so that they are angled down just slightly then tighten the bolt securely. Attach the remaining air hose to the “Y” connector, route the hose up over the top and to the rear of the engine. Cross the hose over to the right side of the rear cylinder head, then behind the electricals of the right side cover and coming out as shown ( see photo 3 A & B ). 5. Remove the center relay from its mounting bracket by lifting it upward and re-attach it lower and at an angle as shown (see photo 3C) using a small cable tie. Route two long cable ties thru the hole in the relay mounting bracket as shown (see photo 3D). Next cut a 16″ wire, strip both ends, crimp female spades to both ends. Attach this wire to the compressors pos (+) terminal. Cut an 8″ wire, strip both ends, crimp a female spade to one end and a fork terminal to the other. Attach this wire to the compressors neg. (-) terminal. Cable tie the compressor securely in place as shown (see photo 4). Route the hose to the compressor making sure there are no tight bends or kinks cut the hose to the desired length and attach it to the compressor. Route the neg. (-) wire with the fork terminal up and attach it to the 10 mm bolt as shown (see photo 4A) . Route the pos. (+) wire over to the relay on the left side of the motorcycle and attach it to terminal 30 or 87 on the relay (see wiring diagram)

Incoming search terms: