where is the fuse on a kawasaki motorcycle for the speedometer located

You search Auto repair manual PDF where is the fuse on a kawasaki motorcycle for the speedometer located, if there are search results will appear below. If search results do not exist, please search by others keyword.



  where is the fuse on a kawasaki motorcycle for the speedometer located Direct Download speed 5282 Kb/s

  where is the fuse on a kawasaki motorcycle for the speedometer located Full Version speed 6162 Kb/s



HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

YAMAHA XVZ 1300 Royal Star/ Venture SPEEDOMETER COWL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 07-11-2010

download
Speedometer Cowling Chrome 1 2 Alcohol Wipe 1 NOTE: Allow time for the 3M® brand quality tape to cure for 24 hours at 19-32° C before washing or waxing the motorcycle. INSTALLATION 1. Position the Speedometer Cowl in front of the Speedometer. The Cowl attaches to the Speedometer Cover, not on the rubber ring around the Speedometer. The Cowl should be symmetrically located in relation to the Speedometer, use the Speedometer markings as a reference. 2. Remove the red backing tape from the adhesive strip on the base of the Speedometer Cowl. 3. Position the Speedometer Cowl as done in step 1. Make any position adjustments now. 4. Firmly press the Speedometer Cowl in place on the Speedometer Cover. 5. Allow twenty-four hours for the adhesive to fully set before washing or waxing.

2004-UP DIGITAL SPEEDOMETER MODULE Owner's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
SPEEDOMETER INSTALLATION The following procedure details the removal of the factory speedometer and installation of the digital speedometer on Softail models; however the process is similar for all other models: 1. Remove the nut and washer (item #4 in the accompanying exploded view) that secures the console (#5) to the fuel tank. 2. Lay a clean shop rag on the fuel tank and flip the console over to expose the underside of the console. 3. Separate the 12-pin harness connector (#2) from the speedometer. 4. Unscrew the rubber cover from the “trip” reset switch (#6) on t left side of the console. he 5. Remove the “trip” switch from the console. 6. Pry between the three tabs that hold the back clamp (#7) to the speedometer (#1). Remove the back clamp from the speedometer. 7. Remove the speedometer from the console. 8. Remove the gasket (#3) from the speedometer. 9. Installation is the reverse of removal. CHAPTER 3 SPEEDOMETER OPERATION When the motorcycle key switch is ON, the speedometer will enter “normal” mode. Pressing the MODE button will cycle through the following display options: Odometer (ODOM) displays the mileage since the speedometer was installed. Trip (TRIP) displays the mileage since the last time the “trip” button was pressed. Head Temp (H TEMP) displays the cylinder head temperature in degrees F. Battery V (BATT V) displays the battery voltage Fuel (FUEL) displays the fuel level in gallons. Miles Per Gallon (MPG) displays the fuel economy in miles per gallon. Range (RANGE) displays the calculated range (in miles) until the tank reaches its empty value. Horsepower (POWER) to perform the horsepower test, follow these steps

HARLEY DAVIDSON COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
Removing the Old Speedometer NOTE This Instruction Sheet covers several different Harley- Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 3. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 4. Unplug the 12-terminal connector (39B) from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 5. Remove the back clamp: All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 6. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 7. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it doesn’t fall off during the following opera- tions. 8. Set the console securelyon the fuel tank. Installation and Final Check NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation. 1. Turn the console over, facing upward. 2. Place the speedometer gasket into position around the console speedometer bore. 3. Fit the new gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment. 4. Turn the console over, face down. 5. Install the back clamp

Motorcycle LED lights RENEGADE LIGHTS Disconnection Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Disconnect the fuse holder from the battery – both the positive ( +) and negative ( -) sides. 4. Cut the wire to the light that is not working with the side cutters. 5. At the problem light twist the light case back and forth slowly and then pull firmly, DO NOT yank to remove from the motorcycle. 6. If the motorcycle led light does not come off easily, repeat the twisting motion back and froth until you feel the light loosen – then pull. 7. Pull the motorcycle led light away from the motorcycle slowly until the cut end of wire falls free. 8. If you will NOT be using your motorcycle until the new lights arrive, you may stop at this step. SAFETY POINT: Otherwise, where you cut the wire, you need to dead end or tape the cut wire. This will keep it from shorting out until the new motorcycle led light is installed. 9. Reconnect fuse holder to battery. 10. Reconnect the battery and then install the seat. 11. Return the motorcycle led light or lights to Renegade Lights along with Warranty Return Policy Form. 12. Renegade Lights will return your new motorcycle led lights along with instructions for installing them.

Incoming search terms:

Vengeance Motorcycle Specification And Owner's Manual

0

Filed Under (Vengeance) by admin on 20-11-2010

download
Vengeance Maxis • Vengeance Raven • Vengeance Banshee • Vengeance Whiplash • Hotrod Drifter • Hotrod CalChop • Hotrod Teacher • Hotrod Bone Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.) • Slow down before you enter the turn; look as far ahead as possible through the turn. • Keep your feet on the pegs, and grip the gas tank with your knees. • Lean with the motorcycle; don’t try to sit perpendicular to the road while the motorcycle is leaning over. • Keep an even throttle through the turn, or even accelerate a little bit. Checking the Bike before the Ride It’s not fun to have things go wrong on a motorcycle, but if you spend a minute before you go off on a ride, you can increase the chances that nothing will.

Incoming search terms:

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

INDIAN MECHANICAL- TO- ELECTRONIC SPEEDOMETER CONVERSION KIT INSTALLATION

0

Filed Under (Indian) by admin on 31-10-2010

download
Speed Sensor Requirement Identification Certain motorcycles are not equipped with a port that will accept a Transmission Speed Sensor. Those models will require a Rear Wheel Speed Sensor. To determine which sensor is required, follow the following procedure: Determine if you have a mechanical speedometer 1. The mechanical speedometer is around 2 ¼” in diameter. 2. On the axle on the left side of the front wheel, there will be a 2″ diameter ‘donut like’ part that the axle passes through. This is the speedometer drive. Attached to the speedometer drive and extending back and up under the fuel tank will be a housed cable. This is the speedometer drive and cable to drive the mechanical speedometer. 3. If these conditions are true, you have a mechanical speedometer. Determine which speedometer drive sensor you need. You must determine if your transmission will accept the transmission sensor. If not, you will need the rear axle sensor. 1. On the top, right, rear of the transmission, will be a 1″ by 1/2″ (approximately) cover held in by one bolt. 2. If you find this then REMOVE the bolt and over. 3. If after removal of the cover you find a larger hole underneath, then you can use the transmission sensor. Figure 1—Transmission Sensor Port (Inset Shows Cover Removed) 4. If you have no cover, or under the cover is not a hole, then you need the rear axle sensor. Be sure to look closely and under the gasket under the cover. 5. If you have no sensor hole, then you need to make sure you have the rear wheel sensor. Contact Thunder Heart Performance if you need to exchange your sensor for a different one. 1.3 Preparation and Painting of the Console Your console is made of Lexan®, which is a clear, durable plastic. It can be painted on the inside (so that outside scratches will not affect the paint), or on the outside. For the best paint results, thoroughly clean the console only with the following cleaners

Incoming search terms:

Incoming search terms: