which wires run continous power to tail light on a 2007 harley davidson sporster

You search Auto repair manual PDF which wires run continous power to tail light on a 2007 harley davidson sporster, if there are search results will appear below. If search results do not exist, please search by others keyword.



  which wires run continous power to tail light on a 2007 harley davidson sporster Direct Download speed 5282 Kb/s

  which wires run continous power to tail light on a 2007 harley davidson sporster Full Version speed 6162 Kb/s



HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL LIGHT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet. 6. Referring to photo (2) remove 2″ of the black tubing exposing the red and black wires on the LEDs. Locate the supplied brake/tail light dual function element (a red wire at one end with a red and orange wire at the other) and wire connectors. Cut all three wires on the dual element to 3″ long. Strip the end of the single red wire on the element and both of the red wires from the LEDs then connect them using one of the blue butt connectors. Connect the two black wires from the LEDs to any one of the black wires on the tail light or signals using one of the supplied splice connectors (place both black wires into one of the holes on the connector). Using the remaining splice connectors attach the red wire from the dual element to the yellow wire on the tail light and the orange wire to the blue wire on the tail light. Turn on the ignition and check that the LEDs are working both as tail and brake lights when the brakes are applied.

Incoming search terms:

HARLEY DAVIDSON SPORSTER, DYNA AND SOFTAIL LICENSE / TURN SIGNAL RELOCATOR INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate mounting bracket from the fender. Remove the two screws from the tail light lens and pull the light outward, unplug the wire connector and set aside. Unplug the turn signal wire connectors from the tail light base and push them out thru the hole in the fender. Looking up underneath the rear fender remove the wires from the clips that secure them to the bottom side of the fender. Cut the wires 2″ from the plugs as shown in photo 1. 2. Unscrew the signal housings from their mounting stems while rotating the wires on the inside of the fender so as not to twist them off while unscrewing the signal from the stem. Remove the signals pushing the wires thru from the inside while pulling the signal outward. Remove the nuts from the backside of the fender that secure the stems and remove the stems. 3. Assemble the license/turn signal bracket, turn signals. Place the smaller reinforcing bracket inside the license plate bracket. Locate the two supplied 5/16″ X 1″ bolts with holes drilled thru the center and the two supplied 5/16″ long spacers. Place the bolts thru the brackets from the inside, threads facing outward followed by the spacers. Thread the wires of the signals thru the bolts and thread the bolts into the signals and snug the bolts. 4. Mounting the LED lights a. Locate the supplied LED tail/brake lights. NOTE: this license plate holder is designed for the new U.S. standardized 7″ wide license plate. If you have an old style wider plate call us at the phone number below and we will send you a separate set of chrome brackets to work with your larger plate at no charge. b. Install the lights as shown in photos 2 & 3. Thread the wires of the LED lights thru the lower holes in the license bracket, peel the adhesive backing and press them firmly in place. Cut the wires off at about 18″ long. c. Install the license plate bracket with signals and LED lights onto the rear fender as shown in photos 2 & 3. Place the two supplied 1/4″ X 1″ flat head screws thru the license plate mounting block. Notice that the thicker half of the mounting block goes toward the top of the fender. d. Next route all the wires from the right turn signal and LED into the slot or notch on the backside of the mounting block followed by the rubber mounting gasket. Install the two nuts from the underside of the fender (Removed from the original license bracket.) onto the two flat head screws and snug them being sure the wires are all in the slot of the mounting block. Run all of the signal and LED wires thru the hole in the fender to the left of the mounting block. e. Install the license plate assembly onto the mounting block using the two supplied 1/4″ X 1/2″ flat head screws. Check the slack from all the wires and again be sure the wires are not pinched between the mounting block and the fender. Tighten all four flat head screws securely. Align the turn signals and tighten their mounting bolts securely.

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

Harley-Davidson FXWG, FXST (all except FXSTS), FXDWG Light Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2012

download
1. Put a pair of male and female clamp halves together just above the lower triple-clamp. Squeeze the ends of the clamp together with a pair of pliers. Diagram A. 2. Have an assistant position the Light Bar Assembly so the lightbar bracket is to the outside of the clamp assembly. Make sure the wires from the Light Bar Assembly are below the lower triple clamp. Diagram B. 3. Insert a Screw through the clamp and Light Bar Assembly mounting bracket and thread on an Acorn Nut. 4. Hold the Light Bar Assembly in place in front of the lower triple clamp, assemble and attach the remaining clamps. 5. With all four clamp assemblies in place, tighten the clamping screws and nuts to 15 ft. lbs. (21 Nm). Refer to the service manual to gain access to the wire harness inside the fuel tank tunnel or inside the frame backbone. Also, verify the appropriate color wires for hook-up of the passing lamps and turnsignals and running lights. Route the wires from the Light Bar Assembly, around the lower triple- clamp, and up to the frame backbone. Secure the wires so they cannot become pinched when turning the fork. A. The short black wires from the Light Bar Assembly connect to the wires powering the running lights. B. The short red wires from the Light Bar Assembly connect to the wires powering the turnsignals. C. The long blue wires from the Light Bar Assembly connect to the wire powering the headlight low beam. After the wires are connected, verify the operation of the passing lamps, running lights and turnsignals. Correct any connection problems before reassembling the motorcycle. Reinstall the fuel tank. Check all fasteners used during this installation for tightness

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

Incoming search terms:

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

Incoming search terms:

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly