windshield disconnect kit

You search Auto repair manual PDF windshield disconnect kit, if there are search results will appear below. If search results do not exist, please search by others keyword.



  windshield disconnect kit Direct Download speed 5282 Kb/s

  windshield disconnect kit Full Version speed 6162 Kb/s



HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ® Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

Incoming search terms:

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan. Lexan is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. Failure to maintain Lexan properly can result in damage to the windshield. (00230a) Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a)

HARLEY DAVIDSON FLST REPLACEMENT WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. See Figure 1. Remove stock windshield. 2. Remove all hardware that secures mounting brackets to windshield. The nine screws must be removed with a T- 27 TORX® screwdriver. Save all hardware and brackets for installing new windshield. 3. Remove all old tape from brackets and apply new tape (1, 2) from kit onto brackets. Align holes in tape with holes in brackets. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets. Tighten all screws and acorn nuts to 48-60 in-lbs (5.4 to 6.8 Nm) . 5. Install windshield (3) on motorcycle CARE AND CLEANING Polycarbonate windscreens/windshields require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windscreen/windshield. (00483d) •Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface. •Do not clean Lexan® polycarbonate in hot sun or high temperature. •Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield. •Never scrape the windshield with a razor blade or other sharp instruments, as permanent damage will result. •Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections. •Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces. Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a) NOTES Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier. Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson Lexan windshields

Incoming search terms:

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
and later FLTR Black wind deflector 57957-98 Fits 1998-2003 FLTR (Domestic) Standard height clear 57958-98A Fits 1998-2003 FLTR Plus 3″ taller, clear 58009-98A Fits 1998-2003 FLTR (International) Standard height, clear 58246-99A Fits 1998-2003 FLTR Low profile smoked 58453-98A Fits 1998 and later FLTR Smoked and contoured low profile 58753-01A Kit Contents Table 2. Kit Contents Part Number Description Quantity Not Sold Separately Windshield 1 There are no Service Parts available with this kit. REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing.

Honda Motorcycle Na vigation Kit

0

Filed Under (Honda) by admin on 28-11-2010

download
Honda Motorcycle Na vigation Kit Honda Motorcycle Navigation Kit G e n e r i c A c c e s s o r i e s 2 0 0 8 For your peace of mind Honda Genuine Accessories are carefully designed, researched and stringently test ed tot he highest standards. And since they’re all Honda approved you’llknowthat they’rejustastoughand well made as your Honda motorcycle. Please Note -All prices quoted are correct at time of printing and are subject to change without prior notice. y e a r w a r r a n t y GENUINE ACCESSORIES Honda Motorcycle Navigation Kit Model Part Number Description RRP Remarks NAKED CBF 600 08A 40MER800B CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY CBF 600 08A 40MER800A CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, £549.99 EARPHONE, MANUAL, MCC AR KIT, UN I TAT TACHM ENT KIT, BATTERY ON/OFF XL700V 08A 40MFF800 * CONTAINS NA VI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EARPH ONE, MANUAL, 08A 30MFF800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY XL 1000V 08A 40MBT800 CONTAINSNAVI GAT ION UNIT COMPONENT, £549.99 Must be combined with quartet harness CONTROLLER, EAR PH ONE, MANUAL, 08A 30MBT800 MCCAR KIT, UNI TAT TACH ME NT KIT, BATTERY TOURERS/SPORT TOUR ERS DN-01 08A 40MEH800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, AND BATTERY -CONTAINS 08A 30MEW800 ADDITIONALSTE ERIN G HANDLE C LAMPS FORV ISU AL INTE GRAT ION OF THE COMPONENT NT700V 08A 40MEW800 CONTAINSNAVI GAT ION UNIT COMPONENT, CONTROLLER, EARPHONE, £549.99 Must be combined with quartet harness MANUAL, MC CAR KIT, UNI TAT TACH MEN T KIT, BATTERY

Incoming search terms:

HARLEY DAVIDSON SKULL FOOT BOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Kit 50704-04 is an Operator Footboard Insert Kit. •This kit fits all 2004 and later FLHRS/I (Road King® Custom) model motorcycles. •This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with Swept-Wing footboard pans 50683-04 (right) and 50688-04 (left) . Kit 50704-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50705-04 1Operator footboard insert (left) 50706-04 Kit 50707-04 is a Passenger Footboard Insert Kit. •This kitfits 2004 FLHTCSE models, and all 1986 and later Touring model motorcycles equipped with Swept- Wing Grooved Passenger Footboard Kit 50357-04 . Kit 50707-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50708-04 1 Passenger footboard insert (left) 50709-04 Kit 50710-04 is an Operator Footboard Insert Kit. •This kitfits all 1980 and later Touring models except FLHRS, and 1986 and later FL Softail®model motorcy- cles equipped with footboard pans 50621-79A. Kit 50710-04 contains the following items: QTY DESCRIPTION PART NO. 1Operator footboard insert (right) 50711-04 1Operator footboard insert (left) 50712-04 Kit 50713-04 is a Passenger Footboard Insert Kit. •This kit fits all 1986 and later Touring models . •This kit also fits 1986 and later FL Softail models when equipped with accessory passenger footboard kits (Part Number 50602-89B, 50955-97A, 50955-00 or 50602-00). • This kit iscompatible with Chrome Passenger Footboard Cover Kits (Part Numbers 50782-91, 50193-96, 50194-96 and 50246-00). • This kit is notcompatible with Leather Passenger Footboard Fringe Kits (Part Numbers 50947-98 or 50956-98). Kit 50713-04 contains the following items: QTY DESCRIPTION PART NO. 1 Passenger footboard insert (right) 50714-04 1 Passenger footboard insert (left) 50715-04 Installation, Kit 50704-04 (For Swept-Wing Operator Footboards): Removing Previously Installed Inserts 1. Apply liquid dishwashing soap to the rubber beads protruding through the bottom of the footboard pan. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Repeat the above steps for the remaining footboard insert. Installing the New Inserts 4. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 5. Place the footboard insert into position on the footboard pan. From the underside of the footboard, use a pliers to pull each rubber bead into its mating hole in the footboard pan until the beads protrude through the pan. 6. Repeat the above steps for the remaining footboard insert.

Incoming search terms:

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

HARLEY DAVIDSON FLHR/ FLHP WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. Remove stock windshield. 2. Remove all hardware that secures the mounting brackets to the windshield. The nine screws that must be removed require a T-27 TORX® screwdriver. Save all hardware and brackets for installing the new windshield. 3. Remove all old tape from the brackets. Apply tape from kit to areas of the new windshield that had tape on the stock windshield. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets and tighten all screws and acorn nuts to 23-27 in-lbs (2.6-3.0 Nm) . 5. Install windshield on motorcycle. Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a) NOTE Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. NOTE Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components. CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

Incoming search terms: