windshield mounting grommets harley

You search Auto repair manual PDF windshield mounting grommets harley, if there are search results will appear below. If search results do not exist, please search by others keyword.



  windshield mounting grommets harley Direct Download speed 5282 Kb/s

  windshield mounting grommets harley Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLST REPLACEMENT WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. See Figure 1. Remove stock windshield. 2. Remove all hardware that secures mounting brackets to windshield. The nine screws must be removed with a T- 27 TORX® screwdriver. Save all hardware and brackets for installing new windshield. 3. Remove all old tape from brackets and apply new tape (1, 2) from kit onto brackets. Align holes in tape with holes in brackets. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets. Tighten all screws and acorn nuts to 48-60 in-lbs (5.4 to 6.8 Nm) . 5. Install windshield (3) on motorcycle CARE AND CLEANING Polycarbonate windscreens/windshields require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windscreen/windshield. (00483d) •Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface. •Do not clean Lexan® polycarbonate in hot sun or high temperature. •Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield. •Never scrape the windshield with a razor blade or other sharp instruments, as permanent damage will result. •Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections. •Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces. Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a) NOTES Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier. Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson Lexan windshields

Incoming search terms:

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON FLHR/ FLHP WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. Remove stock windshield. 2. Remove all hardware that secures the mounting brackets to the windshield. The nine screws that must be removed require a T-27 TORX® screwdriver. Save all hardware and brackets for installing the new windshield. 3. Remove all old tape from the brackets. Apply tape from kit to areas of the new windshield that had tape on the stock windshield. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets and tighten all screws and acorn nuts to 23-27 in-lbs (2.6-3.0 Nm) . 5. Install windshield on motorcycle. Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a) NOTE Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. NOTE Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components. CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan. Lexan is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. Failure to maintain Lexan properly can result in damage to the windshield. (00230a) Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a)

HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ® Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

Incoming search terms:

HARLEY DAVIDSON SPORT WIND DEFLECTOR AND WINDSHIELD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 03-03-2011

download
HEADLAMP VISOR INSTALLATION (2004 ONLY) 1 2 is 01467 1. Headlamp 2. Headlamp bracket mounting screws Figure 1. Remove Headlamp Mounting Screws (Left Side Shown) 1. See Figure 1. While holding the headlamp (1), remove the left and right headlamp bracket mounting screws (2). 2. See Figure 5. Obtain the headlamp visor (2) from the kit. 3. See Figure 2. Orient the headlamp visor (1) between the headlamp and headlamp mounting bracket (2) and reinstall the headlamp bracket mounting screws (3) securing the visor and headlamp to the headlamp mounting bracket. 4. Refer to the Service Manual and adjust the headlamp for the correct angle. 2 1 3 is01468 1. Headlamp visor 2. Headlamp mounting bracket 3. Headlamp mounting bracket screw Figure 2. Install Visor Between Headlamp and Mounting Bracket (Left Side Shown) 1 2 3 is03212 1. “RT” or “LFT” marking 2. Hinge-pin head faces up 3. Clamp post socket faces outward Figure 3. Fork Tube Clamp and Post Identification (Right-Side Clamp Shown) WINDSHIELD INSTALLATION 1. See Figure 5. Obtain one of the lower mount kits from the windshield kit carton. Identify the fork tube clamp for right- side (RT) or left-side (LFT) installation as indicated in Figure 3. NOTE The lower grommets (4) have been pre-installed into the Lexan® windshield. 2. Insert the rounded end of the post into the socket in the fork-tube clamp, oriented as shown in Figure 5. Lining up the hole in the end of the post with the hole in the clamp. With a 3 mm hex key, fasten the post to the clamp with the flat-head screw (16) from the kit, and tighten to 6.8 Nm (60 in-lbs ). 3. Place the clamp around the correct-side fork tube with the hinge-pin head facing up. Insert the two longer screws (15) from the lower mount kit through the counterbored holes in the outboard side of the clamp, and thread the screws part-way into the tapped holes in the inboard half. 4. Position the clamp so the top surface is approximately 6 to 13 mm (1/4 to 1/2 inch) below the upper triple-tree, and the hinge pin is straight forward. With a 4 mm hex key, tighten the screws just enough to hold the clamp in posi- tion. 5. Obtain the remaining lower mount kit and repeat Steps 2 through 4 to install the clamp to the opposite fork tube. 6. Obtain the upper mount kit from the windshield kit carton. NOTE The upper grommets (4), socket assemblies (3), windshield mount caps (6) and 5 mm screws (9) have been pre-installed into the windshield. 7. Place one of the handlebar clamps (5) onto one side of the handlebar, in the straight section between the riser and the handlebar controls, oriented as shown in Figure 4. NOTE Temporarily disengage the switch harness retainer from the handlebar to allow installation of the clamp.

Incoming search terms:

HARLEY DAVIDSON MULTI-POCKET WINDSHIELD BAG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation 1. Remove the acorn nuts from the inside-center, left and right on the horizontal windshield bracket. 2. Apply protective tape strips to the horizontal windshield bracket to protect chrome finish. 2. Place windshield bag and bracket with eyelets over screws in the horizontal windshield bracket. Mark the location of the vertical supports for correct placement of the rubber bumpers to protect the bottom of the bag bracket. Place two bumpers each at the marked locations of the vertical windshield supports. 3. Align the metal brace with the eyelets, to fit snugly onto the windshield horizontal bracket screws. 4. Fasten the acorn nuts removed in step 1 onto the screws through the eyelets under the windshield bag. Torque the nut to 90-110 in-lbs (10.2-12.4 Nm). NOTE The brace under the bottom of the windshield bag conforms to the contour of the windshield bracket as the acorn nuts are torqued. To keep this surface in the best condition, lightly wipe with a Harley-Davidson Micro Fiber cloth, part number 94663-02, using clear water or a mild Harley-Davidson cleaner such as: • Sunwash (part number 94659-98), • Bug Remover (part number 94657-98) or • Harley Gloss (part number 94627-98).

HARLEY DAVIDSON RIDER BACKREST MOUNTING HARDWARE KIT INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION 1. Remove seat according to the instructions in the service manual. 2. Remove the ECM caddy/battery cover by removing two screws. 3. See Figure 1 and Figure 2 for the mounting locations of the brackets. NOTE Some seats may limit the fore/aft mounting location of the backrest bracket. 4. See Figure 3 and Table 1. Remove plastic protective cap and locknut from stud. Leave the small plastic washer in place or the stud plate will fall out. With the backrest mounting bracket tab facing forward, attach the backrest mounting bracket (1) to stud plate with stock locknuts from the stud plate. 5. Tighten locknuts to 5-8 ft-lbs (6.8-10.8 Nm) . 6. Attach the front mounting bracket (6) to the frame cross- member using using two flange screws (8) and flange nuts (7). Tighten screws to 72 in-lbs (8.1 Nm) . 7. Attach the bracket support (2) to the front mounting bracket (6) with screw (8) and nut (7). 8. Install screw (5) and nut (9) to bracket support and backrest tab and tighten to 15 ft-lbs (20.3 Nm) . 1 2 is05475 1. Backrest mounting bracket 2. Front mounting bracket Figure 1. Bracket Mounting Locations 3 2 1 is05476 1. Backrest mounting bracket 2. Front mounting bracket 3. Bracket support Figure 2. Backrest mounted After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) -J04733 1 of 2
9. Install the ECM caddy/battery cover using two screws previously removed and tighten to 6-8 ft-lbs (8.1-10.8 Nm) . 10. Install seat according to service manual instructions. 11. Hold slit between rider and passenger seat open. On rider backrest, compress backrest rods and spring. Insert rods into backrest mounting bracket. Backrest Pad Adjustment 1. Adjust fore/aft position of backrest pad. Use 3/16 inch hex wrench to adjust set screw that is accessible through eyelet opening on rear of pad. If possible, do not remove set screw because it is difficult to install.

Incoming search terms:

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
and later FLTR Black wind deflector 57957-98 Fits 1998-2003 FLTR (Domestic) Standard height clear 57958-98A Fits 1998-2003 FLTR Plus 3″ taller, clear 58009-98A Fits 1998-2003 FLTR (International) Standard height, clear 58246-99A Fits 1998-2003 FLTR Low profile smoked 58453-98A Fits 1998 and later FLTR Smoked and contoured low profile 58753-01A Kit Contents Table 2. Kit Contents Part Number Description Quantity Not Sold Separately Windshield 1 There are no Service Parts available with this kit. REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing.

HARLEY DAVIDSON FL ADJUSTABLE RIDER BACKREST MOUNTING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
REMOVAL 1. Remove existing seat and grab strap (if equipped) following instructions in the service manual. 2. Refer to the service manual and remove the left side cover and battery. 3. See Figure 5. Pull plastic spark plug wire clip out of the hole in the frame plate at the location where the adjustment handle bracket is going to mount. Discard plastic hose clip. 4. Remove the mid-frame air deflector upper left mounting bolt and washer. Save for installation. 5. If equipped with a grab rail: See Figure 1. Remove grab rail screws (1) and discard. 6. Remove wire harness retention clip located above the bank angle sensor. Discard clip. 7. Remove screws (3) holding the bank angle sensor (4). 1 3 2 4 is06104 1. Grab rail screw (2) 2. Grab rail 3. Bank angle sensor screw (2) 4. Bank angle sensor Figure 1. Remove Bank Angle Sensor Screws INSTALLATION 1. See Figure 2. Install clip nut (1) in mounting hole (2). Align the clip nut hole with alignment hole (3). Follow the instructions included with the Mid-Frame Air Deflector Kit to install the four self-clinching special nuts. 2. Move the electrical connector so that the backrest mounting base does not interfere with it. 3. See Figure 3. Install mounting bracket (8) to mounting base (4) with screw (6) and flange nut (7). Tighten screw to 72-96 in-lbs (8-11 Nm) . NOTE Only use the specified screw to install the mounting bracket to the bank angle sensor. 4. Secure the mounting bracket (8) to the bank angle sensor bracket with 1/4-20 x 5/8 inch screws (5). 5. If installing grab strap (9), install backrest mounting base and grab strap with screws (1) and washers (2). If grab rail is installed, install backrest mounting base with screws (1) and washers (2)

Incoming search terms: