wiring loom for a sr aprilia

You search Auto repair manual PDF wiring loom for a sr aprilia, if there are search results will appear below. If search results do not exist, please search by others keyword.



  wiring loom for a sr aprilia Direct Download speed 5282 Kb/s

  wiring loom for a sr aprilia Full Version speed 6162 Kb/s



HARLEY DAVIDSON WIRE LOOM AND HORNS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
Remove the stock horn and bracket from the stud it is mounted to and unplug the 2 wires. Remove the seat. Route the end of the wire and hose loom without the connectors. Starting in front of the fuel valve, route this loom behind the valve, over the fuel line over the rear cylinder head along the existing wiring or hoses – if your model has any. Follow the frame to where the back bone and seat support rails come together. Route the loom up into the general area where the compressor will mount (i.e. see diagram). Attach the hose to the ‘Y’ connector on the horns themselves. Attach the two black wires from the loom to the relay terminals #87 and #30, located between the air horns behind chrome cover. Attach the wires from the original horn to the remaining terminals #85 and #86 (NOTE: it makes no difference which wire goes to which terminal). Attach the relay to the back of the horn bracket assembly or up under the fuel tank using the small cable tie provided. NOTE: the terminals must point downward to prevent water from entering the relay! Install the horn assembly using the 1/4″ thick chrome washer provided behind the horn mounting bracket. Use the original acorn nut and tighten securely. Check to see that the horns have at least 1/4″ clearance between the engine, shift linkage and choke knob. They should be horizontal or angle down at the front just slightly. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. COMPRESSOR MOUNTING AND WIRING Due to the vast differences in years and models, it is not possible to have one or two brackets that will fit all models. You may need to mount the compressor in a different position or find an alternative location, such as under one of the side covers. On 2001 and newer Tour models there is room in front of the battery to mount it horizontally. On 1997-2000 fuel injected models, under the front portion of the right hand side cover is an excellent location. On most Softtail models you can attach it to the frame tube behind the rear cylinder. On some models such as Sportsters there may not be a place to conceal the compressor; there is a chrome cover and cap available to dress it up for exposed mounting. (RIVCO part no #CMPCR) If mounting the compressor vertically as pictured, try to keep the end with the electrical terminals pointing downward. You can use the long cable ties provided to attach the compressor to the frame or an existing wiring loom. Once the compressor has been mounted securely, route the hose and one of the wires to it and connect the hose to the air outlet barb or fitting. Trim the wire and crimp on one of the female blade terminals and attach to the (+) terminal. Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Trim and crimp another female terminal to it. Attach this wire to the (-) ground terminal. The remaining black wire from the hose/wire loom goes to the battery (+) terminal through the fuse and holder provided. Trim the black wire allowing for the length and placement of the fuse holder. Crimp together and attach to the battery (+) terminal. Turn ignition on and test horns. Check wires and hoses for neat, secure routing and at least 1″ away from exhaust system. Reinstall seat etc.

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

2009 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
1. MACHINES Aprilia RS 125 production models, as produced from 01-11-05 and available in the UK via IN Competition from 01-01-06. (any parts exclusive to the older models including the pre-1999 SP model are not permitted to be used on machines in this series). The only eligible models are designated as Euro 2 & Euro 3 New machines are supplied with race kits included through: IN Competition Unit 1 New Lane Burscough Lancs 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT RED background with WHITE numbers – Nitro Newcomers Class BLACK background with WHITE numbers – Aprilia Championship Class REAR BLACK background with WHITE numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. E85 Bio Fuel is also permitted when purchased from normal roadside outlets. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer and may not be painted. The sides of the frame body may be covered by a protective part made of composite material of the original frame colour. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Bolt on accessories to the rear sub-frame may be removed. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm)

Incoming search terms:

2010 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
1. MACHINES Aprilia RS 125 production models, as produced from 01-11-05 and available in the UK via IN Competition from 01-01-06. (any parts exclusive to the older models including the pre-1999 SP model are not permitted to be used on machines in this series). The only eligible models are designated as Euro 2 & Euro 3 New Euro 2 machines are supplied with race kits included through The machines used are allowed only limited modifications. Most modifications are allowed only on safety and cost control grounds. All motorcycles must comply in every respect with all requirements for Road Racing as specified in the ACU regulations. The appearance from both front, rear and profile of machines must (except when otherwise stated) conform to the homologated shape. The appearance of the exhaust system is excluded from this rule. 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT RED background with WHITE numbers – Nitro Newcomers Class BLACK background with WHITE numbers – Aprilia Championship Class REAR BLACK background with WHITE numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted. 6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. E85 Bio Fuel is also permitted when purchased from normal roadside outlets.

Incoming search terms:

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

2003 Aprilia Tuono Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Remove the main seat and the passenger seat. 2. Prop the front of the fuel tank in the up position. 3. Route the PCIII harness from the trunk area towards the front of the bike. Route the PCIII harness under the fuel tank bracket (Fig. A). 4. Attach the ground wire from the PCIIIharness to the negative side of the battery. (fig. B). 5. Locate the Throttle Position Sensor on the backside of the throttle bodies (Fig. C). 6. Locate the BROWN wire with the YELLOWtracer and attach the supplied wire tap to the wire. NOTE: It is recommended to use dielectric grease on this connec- tion. Fig. A Fig. B Fig. C 2003 Aprilia Tuono – PCIII USB – 2 i907-411 www.powercommander.com Wire tap Ground wire from PCIII TPSI connector 7. Attach the grey wire from the PCIII to the wire tap (Fig. D). NOTE: It is recommended to use dielectric grease on this connec- tion. 9. Plug the YELLOWcolored wires from the PCIIIharness in- line of this connection. (fig. F) Fig. D Fig. E Fig F 2003 Aprilia Tuono – PCIII USB – 3 i907-411 www.powercommander.com Stock connector Grey wire from PCIII PCIII connectors Stock connector 8. Unplug the stock wiring harness from the rear injector (left hand side of the throttle body). Fig. E 10. Unplug the stock wiring harness from the front injector (right hand side of the throttle body). Fig. G 11. Plug the ORANGE colored wires from the PCIIIharness in- line of this connection

2008 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
specified in the ACU regulations. The appearance from both front, rear and profile of machines must (except when otherwise stated) conform to the homologated shape. The appearance of the exhaust system is excluded from this rule. 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT Red background with white numbers – Nitro Newcomers Class White background with black numbers – J&S Championship Class REAR White background with black numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer. The sides of the frame body may be covered by a protective part made of composite material. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Rear sub-frame may be replaced by the later type sub-frame to accept new style bodywork on pre-2006 models, this unit must use the original mounting points. Bolt on accessories to the rear sub-frame may be removed. Front fairing bracket may be altered or replaced on pre-2006 models to accept later bodywork. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm) Every part of the rear fork must remain as originally produced (including rear fork pivot bolt and rear axle adjuster). Rear wheel stand positioning (support) brackets may be added by welding or bolts. Brackets must have rounded edges viewed from all sides. Fastening screws must be recessed. 10. REAR SUSPENSION UNIT

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

Incoming search terms:

APRILIA TUONO V4 R APRC Technical specifications

0

Filed Under (Aprilia) by admin on 16-11-2010

Engine type Aprilia longitudinal 65° V-4 cylinder, 4-stroke, liquid cooling system, double overhead camshafts (DOHC), four valves per cylinder Fuel Unleaded petrol Bore and stroke 78 x 52.3 mm Total engine apacity 999.6 cc Compression ratio 13:1 Maximum power at crankshaft 162 hp (119 kW) at 11,000 rpm Maximum torque at crankshaft 110 Nm at 9,000 rpm Fuel system Airbox with front dynamic air intakes. 4 Weber-Marelli 48-mm throttle bodies with 4 injectors and latest generation Ride-by-Wire engine management. Choice of three different engine maps selectable by the rider with bike in motion: T (Track), S (Sport), R (Road) Ignition Magneti Marelli digital electronic ignition system integrated in engine control system, with one spark lug per cylinder and “stick-coil” type coils Starting Electric Exhaust system 4 into 2 into 1 layout, single oxygen sensor, lateral single silencer with engine management system controlled butterfly valve and integrated trivalent catalytic converter (already meets future Euro4 regulations) Alternator Flywheel mounted 420W alternator with rare earth magnets Lubrication Wet sump lubrication system with oil radiator and two oil pumps (lubrication and cooling) Gearbox 6-speed cassette type gearbox 1st: 39/15 (2.600) 2nd: 33/16 (2.063) 3rd: 34/20 (1.700) 4th: 32/22 (1,455) 5th: 34/26 (1,308) 6th: 33/27 (1,222) Gear lever with Aprilia Quick Shift electronic system (AQS)
Clutch Multiplate wet clutch with mechanical slipper system rimary drive Straight cut gears and integrated flexible coupling, drive ratio: 73/44 (1,659) Secondary drive Chain: Drive ratio: 42/16 (2.625) Traction anagement APRC System (Aprilia Performance Ride Control), which includes Traction Control (ATC), Wheelie Control (AWC), Launch Control (ALC), all of which can be configured and deactivated independently. Frame Aluminium dual beam chassis with pressed and cast sheet elements. Sachs steering damper. Front suspension Sachs upside down front fork with Æ 43 mm stanchions. Low profile forged aluminium calliper mountings for radial callipers. Completely adjustable spring preload and hydraulic compression and rebound damping. Wheel travel: 120 mm

HARLEY DAVIDSON FLSTF TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. See Figure 1. Disconnect battery cables, negative (-) cable first. 2 1 is03242 1. Negative (-) cable 2. Tail lamp connector Figure 1. Negative Battery Cable and Tail Lamp Connector 3. See Figure 2. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 2. Remove Tail Lamp Lens 4. See Figure 3. Using a Terminal Pick Tool (1), depress locking tabs and disconnect turn signal connectors (2- place) (2, 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. 6. See Figure 4. Remove turn signal wiring (1, 2) from clips (3) under rear of fender INSTALLATION NOTE Proper installation of kit requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Route Turn Signal Wiring Through Rear Fender and Support 1. See Figure 5. Remove three rear screws (1) from fender support (2). 2. Loosen, but do not remove two front screws (3) from fender support. 1 3 2 is03285 1. Screw, rear (3) 2. Fender support 3. Screw, front (2) Figure 5. Fender Support Screws and Fender Support 3. Pull fender support away from rear fender to gain access to turn signal mount. 4. Remove stock screw and washer from turn signal mount. 5. See Figure 7. Pull turn signal (B) and turn signal mount (A) away from fender support. 6. Remove turn signal and wires from vehicle by routing turn signal wiring and connector through holes in rear fender and fender support. Gently guide wires through holes to ensure they do not get damaged. Feed Wiring and Install Relocation Bracket 1. See Figure 6. Feed turn signal wiring and connector through middle hole in turn signal relocation bracket and under rear of fender support. 1 is04635 1. Wire harness Figure 6. Wire Harness Routing 2. See Figure 7. Insert stock screw and washer through rear hole of relocation bracket (1) and turn signal mount (A). 3. Thread screw into turn signal (B). Tighten to 12-16 ft-lbs (16.3-21.7 Nm). 4. Align relocation bracket (1) with rear of fender support and install with screw (2) and nut (3) from kit. Tighten nut to 12-16 ft-lbs (16.3-21.7 Nm). Complete Turn Signal Relocation Wiring 1. See Figure 5. Install one rear screw (1) to hold fender support in place while routing wiring. Install screw snugly but do not fully tighten

Incoming search terms:

Incoming search terms: