wiring up an electronic single fire ignition on a shovelhead

You search Auto repair manual PDF wiring up an electronic single fire ignition on a shovelhead, if there are search results will appear below. If search results do not exist, please search by others keyword.



  wiring up an electronic single fire ignition on a shovelhead Direct Download speed 5282 Kb/s

  wiring up an electronic single fire ignition on a shovelhead Full Version speed 6162 Kb/s



NORTON LIGHTWEIGHT TWIN ELECTRONIC IGNITION Installation Instructions

0

Filed Under (Norton) by admin on 31-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensers and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensers. The condensers are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. • BLACK COIL LINK WIRE • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition coil #1. See figs. 1/2 on page 7. 12. For NEGATIVE EARTH electrics go to step 15. 13. For POSITIVE EARTH electrics (standard): Take the white wire from the ignition module, cut to length and fit an insulator and male spade connector to the end. Connect to one of the negative ignition feed wires previously removed in step 7. The other wire (if fitted) is spare and should be covered with insulation to prevent shorting to the frame etc. 14. Take the red earthing wire, fit an insulator and female spade connector on one end and connect to the positive (+) terminal on ignition coil #1. Cut to length and fit a ring terminal on the other end and connect to a good earth point on the frame, ideally the battery positive (+) terminal. See fig.1 GOTO STEP 17.

Incoming search terms:

NORTON TWIN CYLINDER MOTORCYCLES ELECTRONIC IGNITION SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Norton) by admin on 31-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensors and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. (The Atlas engine has the points housing behind the cylinder head). 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensors. The condensors are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. On the Norton Commando, remove the white-blue wire from the ballast resistor between the two ignition coils; the ballast resistor is no longer required. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition

Incoming search terms:

Harley-Davidson Electronic Ignition Module Installation instructions

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
Step 1: Switch main dashboard switch to “off” position (Ignition& light switch) Step 2: Disconnect negative (ground) cable from the Battery Step 3: Remove the Condenser and Breaker points from the circuit breaker timing base. Step 4: Disconnect advance/ retard cable from timing base Step 5: Remove timing base from timer shaft and housing (see your manual for instructions) Step 6: Remove circuit breaker wire stud or circuit breaker to coil wire assembly from timing base Step 7: Remove circuit breaker wire from Ignition coil, and mark terminal on coil with piece of tape. Step 8: Install the Electronic Ignition Module on the timing base. Mount this short black wire to one on the timer base screws by keeping some slack in this wire so the timing base can turn free. Solder the flag terminal to this short black wire and mount it under the timer to motor bolt. This way of mounting provides a much better grounding. Do NOT use the screws (number 1 or 2 screws from picture below) from the timing base!!!! Step 9: Now three wires pass this hole via the rubber grommet. Figure 1 Figure 2 Step 10: Reinstall the timer base on the timer shaft housing, and keep some slack in the wires before protruding the hole in the timer shaft housing, and secure with ground spring and cover retainer. Reconnect the advance/retard cable to the timer base. Step 11: Route the two long wires to the ignition coil. Check in the HD service manual for a proper route to the ignition coil. (Keep away from hot surfaces like exhaust systems). Cut the wires to the exact length necessary for mounting. Step 12: Determine the exact length of the wire loom. Keep in mind that one end of the loom enters the timer shaft housing by 1cm. Cut the loom to the proper length. Step 13: Insert both wires in the loom. Strip both wire ends and solder the two flag terminals on the wires. Step 14: Connect the red wire to the ignition coil, on the terminal where the 6 or 12 volt is supplied to. This terminal has at minimum one wire connected which runs to the main switch. Step 15: Connect the black wire to the ignition coil on the terminal which is empty, and has piece of tape on it. (Old place where the circuit breaker wire was connected to) Step 16: Install the trigger rotor on the timer shaft cam, and tighten the hex screw by using the hex key tool. Do not over tighten the screw! Step 17: Check for clearance between trigger rotor and Electronic Ignition Module. Appropriate clearance is between 0,5mm and 1,5mm . Minor adjustments can be made by unlocking the two screws and slightly shift/move the Electronic Ignition Module. Check if the rotor moves free. Timing instructions: Remove the spark plugs from the engine, but keep them connected to the spark coil cables and engine ground. This enables normal operation of the spark, and prevents unwanted engine firing on compression stroke. See service manual or handbook for timing instructions of your model Step 18: Reconnect the negative (ground) cable to the battery. Step 19: Switch main power to “on” position. The red light in the Electronic Ignition Module might already light up. If not, turn the kick starter slowly. The red light is on while charging (closed points)the Ignition coil, facing solid metal of the trigger rotor. The light goes off (open points) when the end of the solid surface of the trigger rotor passes the centre of the Electronic Ignition Module. At that point a spark is generated by the coil

Incoming search terms:

Kawasaki Sxi/ SXR Ignition twin cylinder Jet Ski ignition Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove electronics enclosure from its mounting location. 2. Unplug and remove the OEM ignition. 3. Set the programming switches on the T3 to your settings. 4. Install the T3 Ignition in the same location in the electronics enclosure. 5. Test the T3 Ignition. 6. Close the electronics enclosure cover plate and mount the module in the PWC. Installation Remove electronics enclosure from its Mounting Location 1. Using a 10mm socket remove the mounting bolts on each side of the electronics enclosure. 2. Remove the enclosure cover and set aside the screws, 2 mounting flanges, ‘O” ring, and enclosure top. Unplug and Remove the OEM Ignition 1. Using 10mm socket, remove bolts from each side of the OEM ignition. Lift out the ignition and unplug all connectors attached to the OEM ignition. Now remove the protective metal plate that was under the ignition and two 3/16″ thick washers under that plate. 2. On 2004 models and newer remove the wire harness for the two black connectors just unplugged from the OEM ignition. Trace each wire from each black connector back to in-line connectors and separate each of these connectors. Set the two harnesses aside. Install the T3 Ignition in the Electronics Enclosure 1. Install the T3 ignition into the mounting bracket supplied with your T3. Slide the end of the ignition module under the lip at the rear of the bracket an press the wire end of the ignition firmly into the bracket. Attach the keeper bracket using two 5mm bolts supplied. Place the ignition/bracket in the location where the OEM ignition and metal plate were removed. Secure the ignition in place with the supplied bolts

Incoming search terms:

TRIUMPH TWIN CYLINDER MOTORCYCLES WITH POINTS IN THE SIDE CASING INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensors and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. (The Atlas engine has the points housing behind the cylinder head). 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensors. The condensors are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. On the Norton Commando, remove the white-blue wire from the ballast resistor between the two ignition coils; the ballast resistor is no longer required. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition • BLACK COIL LINK WIRE • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3 coil #1. See figs. 1/2 on page 7. 12. For NEGATIVE EARTH electrics go to step 15. 13. For POSITIVE EARTH electrics (standard): Take the white wire from the ignition module, cut to length and fit an insulator and male spade connector to the end. Connect to one of the negative ignition feed wires previously removed in step 7 (white-blue wire for Norton Commando). The other wire (if fitted) is spare and should be covered with insulation to prevent shorting to the frame etc. 14. Take the red earthing wire, fit an insulator and female spade connector on one end and connect to the positive (+) terminal on ignition coil #1. Cut to length and fit a ring terminal on the other end and connect to a good earth point on the frame, ideally the battery positive (+) terminal. For the Norton Commando, the earth tag on the end of the condensor pack can be used (fit a female spade connector to the end of the red earthing wire). See fig.1 GOTO STEP 17

Incoming search terms:

4-STROKE TRIUMPH SINGLE CYLINDER MOTORCYCLES ELECTRONIC IGNITION SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 27-10-2010

download
1. Remove the petrol tank (and seat if necessary) to gain access to the ignition coil, condensor and wiring. 2. For safety, disconnect the battery, if fitted (preferably both terminals). 3. Remove the spark plug. 4. Remove the alternator rotor cover (if fitted). 5. Loosen the auto-advance centre bolt. Rotate the engine to the correct full advance timing position for your machine (see table on page 6), using one of these methods: • Models from 1967 on: use the marks provided for strobe timing on the rotor & chaincase (inside the rotor cover). Unless these marks are known to be accurate it is recommended that they are checked for correct alignment. These marks should line up at the full advance position, check using one of the methods below and, if necessary, re-mark the rotor. • Models from 1969 on: use the timing plug on the left-hand crankcase • Use a degree disc on the crankshaft / camshaft (see table on page 6) • Use a dial guage down the spark plug hole (see table on page 6) 5. Remove kickstart, gear lever and outer timing cover. 6. Remove the contact-breaker plate and lead from the outer timing cover. 7. Taking the ignition trigger assembly, insert a small cable tie into the two holes in front of the connector block on the ignition trigger. This will be used later to secure the two wires to the plate. 8. Fit the ignition trigger plate with the adjustable slots at approx. 6 & 12 o’clock, using the original pillar fixings & washers, positioned in the centre of the slots (to allow for adjustment in either direction). Handle the trigger with care. • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3
9. Remove the centre bolt securing the auto-advance unit. Remove the complete auto-advance unit with an extractor bolt or by tapping it gently sideways. 10. Fit the magnetic rotor in place of the auto-advance unit, with the magnets/ red marks positioned at approx. 3 & 9 o’clock. The magnetic rotor has a male taper which fits into the taper in the end of the camshaft. There is no keyway, allowing it to be fitted in any desired position. 11. Using the ¼” washer and the appropriate bolt (UNF or BSF), pass the bolt through the centre of the magnetic rotor and into the thread in the camshaft. Finger tighten only at this stage. The magnetic rotor centre thread (metric M8) is provided for attaching a puller, if the rotor should need to be removed for engine servicing, etc. 12. Replace the outer timing cover, gear lever & kickstart. 13. Check that the engine is still at the correct full advance position, then adjust the magnetic rotor position so that one of the red marks is centrally behind the static timing hole at 9 o’clock (see fig. 4, page 7). If your machine’s camshaft rotates clockwise, refer to fig. 3. Gently tap the rotor into the taper & tighten the centre bolt, using a 3/16″ allen key. WIRING: 14. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. Avoid coiling up surplus lead.

Incoming search terms:

SUZUKI SV 1000 RADIATOR (COOLING SYSTEM) SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
FI SYSTEM MALFUNCTION CODE AND DEFECTIVE CONDITION MALFUNCTION CODE DETECTED ITEM DETECTED FAILURE CONDITION CHECK FOR COO NO FAULT C11 Camshaft position sen- sor The signal does not reach ECM for more than 3 sec . after receiving the starter signal . The camshaft position sensor wiring and mechanical parts (Camshaft position sensor, intake cam pin, wiring/coupler con- nection) C12 Crankshaft position sensor The signal does not reach ECM for more than 2 sec . after receiving the starter signal . The crankshaft position sensor wiring and mechanical parts (Crankshaft position sensor, wiring/coupler connection) C13 Intake air pressure sensor The sensor should produce following voltage . (0.50 V < sensor voltage < 4 .85 V) Without the above range, C13 is indicated. Intake air pressure sensor, wiring/coupler connection C14 Throttle position sen- sor The sensor should produce following voltage . (0.20 V < sensor voltage < 4 .80 V) Without the above range, C14 is indicated. Throttle position sensor, wiring/coupler connection C15 Engine coolant temperature sensor The sensor voltage should be the following. (0.15 V <_ sensor voltage < 4 .5 V) Without the above range, C15 is indicated. Engine coolant temperature sensor, wiring/coupler connection C21 Intake air temperature sensor The sensor voltage should be the following. (0.15 V < sensor voltage < 4 .5 V) Without the above range, C21 is indicated. Intake air temperature sensor, wiring/coupler connection C22 Atmospheric pressure sensor The sensor voltage should be the following. (0.50 V < sensor voltage < 4 .5 V) Without the above range, C22 is indicated. Atm. pressure sensor, wiring/coupler connection C23 Tip over sensor The sensor voltage should be the following for more than 2 sec . after ignition switch turns ON . (0 .20 V < sensor voltage < 4 .80 V) Without the above value, C23 is indicated. Tip over sensor, wiring/coupler connection C24 or C25 Ignition signalCrankshaft position sensor signal is produced and ECM determines the ignition signal but signal from ignition coil is interrupted continuous by 4 times or more. In this case, the code C24 or C25 is indicated. Ignition coil, wiring/coupler connection, power supply from the battery SERVICING INFORMATION 8 .3 C28 Secondary throttle valve actuator No operating voltage is supplied from the ECM, C28 is indicated. STVA can not operate. STVA lead wire/coupler, STVA C29 Secondary throttle valve position sensor The sensor should produce following voltage . (0.10 V < sensor voltage < 4 .90 V) Without the above range, C29 is indicated . Secondary throttle position sensor, wiring/coupler connection C31 Gear position signalGear position signal voltage should be higher than the following for more than 2 seconds. (Gear position switch voltage >_ 0 .6 V) Without the above value, C31 is indicated. Gear position sensor, wiring/coupler connection, gearshift cam, etc. C32 or C33 Fuel injector Crankshaft position sensor signal is produced and ECM determines the injection signal but fuel injection signal is interrupted continuous by 4 times or more. In this case, the code C32 or C33 is indicated. Injector, wiring/coupler connection, power supply to the injector C41 Fuel pump relay No voltage is applied to fuel pump although fuel pump relay is turned ON, or voltage is applied to fuel pump although fuel pump relay is turned OFF . Fuel pump relay, connecting lead, power source to fuel pump relay C42 Ignition switchIgnition switch signal is not input in the ECM . Ignition switch, lead wire/coupler C44 Heated oxygen sensor (HO2S) [For E-02, 19] During 02 feedback control, 02 sensor voltage is higher or lower than the specification . No signal is detected during engine operation or no electrical power is supplied from the battery . HO2S lead wire/coupler connection Battery voltage supply to the HO2S C49 PAIR control solenoid valve (PAIR valve) When no operating voltage is supplied from the ECM, C49 is indicated. PAIR valve can not operate. PAIR valve lead wire/coupler

Incoming search terms:

HI-4 DUAL FIRE MOTORCYCLE IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 3. Remove OE ignition module and wire harness (items 1-4). You will disconnect two wires at the coil (15), a wire going to the VOES (Vacuum Operated Electrical Switch) (18), a black ground wire at the ignition module, and the 3 pin plug (20) that connects to the sensor plate (11). Refer to shop manual for locations. 3. Remove ignition cover plates and gasket (items 5- 9). This will require drilling out two rivets. The rivets will later be replaced with two supplied self- threading screws. 4. In order to remove the sensor plate cable, the cable plug (20) must be removed first. Use needle nose pliers to pull the terminals out of the plug. Then pull the cable through the exit hole at the bottom of the timing cover. 5. Note location of sensor plate (11). There is a V notch in the sensor plate used for alignment. When you install the HI-4, you should align the V notch in the same location. This should set the timing close enough to start the engine. Remove and save the two standoffs and washers (10). Remove the sensor plate (11). HI-4 INSTALLATION Refer to Figure 4. The HI-4 requires use of the OE timing rotor P/N 32402-83 (used only on 1985 and newer models). If you have an older model or are not sure, check the rotor (9) for the correct part number. For models prior to 1980, use the supplied 10-32 x ¾”bolt and washer to mount the rotor. 1. Install the HI-4 system in place of the OE breaker or sensor plate. Rotate the HI-4 about 90 degrees to give better access to the cable exit hole. Install the HI-4 first, then push the cable through the hole. On some early models it may be necessary to enlarge the wire harness exit hole in the gear cover. Align the V notch on the HI-4 same as the OE plate you removed. Use the OE standoffs to secure the HI-4. You must use lockwashers under the standoffs for proper clearance between the HI-4 and cover plate. Do not fully tighten the standoffs until the timing has been set. 2. Route the HI-4 wire harness along the frame rails up to the coil. Make sure that harness will not be chafed or burned by exhaust heat. Secure harness with tie wraps. Do not install timing cover. HI-4 HOOKUP Crimp terminals and hardware are supplied for your convenience. Use the ring terminals for coil hookup. Use male-female quick disconnects for connections to the tach and vacuum switch (VOES). Tape up any unused wires. 1. Circuit Breaker Cover Screws (2) 2. Circuit Breaker Cover 3. Circuit Breaker Cover Gasket 4. Breaker Plate Screws (2) 5. Breaker Plate Screw Lockwashers & Washers (2 each) 6. Retainer (1971 to early 1972) 7. Circuit Breaker Cam Bolt 8. Breaker Plate Assembly 9. Breaker Cam 10. Advance Assembly 11. Gear Case Cover 11 10 9 8 7 6 5 4 3 2 1 NOTE: Damage will result if the brown tach wire comes in contact with +12V. Figure 1. Harley-Davidson®OE Points System
9000-4002A REV A 3 2/05 1. Identify switched +12 volt wire and tach wire (if equipped) going to the coil. Refer to your service manual, or reconnect the battery and use a test light or voltmeter. The switched +12 volt wire will be hot when the ignition key is turned on. 2. Refer to Figure 5. Connect the HI-4 red wire and switched +12 volt wire to Coil positive. 3. The HI-4 white wire is not used and should be taped. 4. Connect the HI-4 black wire to the Coil negative terminal. 5. Connect the HI-4 green wire to the vacuum switch (Figure 3, item 18), if used. 6. Connect the HI-4 brown wire to the tach wire, if equipped with tach. Tape up if unused. 7. The HI-4 is grounded via the timing housing; a separate ground connection is not required. 8. Reconnect battery ground cable. Verify proper ground connections to the frame and engine. VOES HOOKUP The OE vacuum switch (VOES) is normally an open circuit. Above 3-5 inch-Hg vacuum, the VOES closes and grounds the vacuum input on the OE ignition module. This increases the total advance generated by the OE ignition module. Vacuum advance improves part throttle 17 16 1. Cover Screws (2) 2. Ignition Timer Cover 3. Ignition Module 4. Timer Plate Screws (2) 5. Washers (2) 6. Screws & Washers (2 each) 7. Shield 8. Sensor 9. Trigger Rotor Bolt 10. Timer Plate 11. Trigger Rotor 12. Advance Assembly 13. Gear Case Cover 14. Ignition Coil 15. Spark Plug Wires (2) 16. Ignition Coil Terminal (FX) 17. Ignition Coil Terminal (FL) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NOTE: Most motorcycle coils do not have terminals marked. Use either terminal for Coil+ (positive) and the other one for Coil- (negative). Warning: The HI-4 (8-1100) Dual Fire ignition will not work with 2 plugs per head, dual coil application. Damage will result if attempted. Use the HI-4 (8-2100) single fire ignition for 2 plugs per head applications

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

TOYOTA COROLLA 1984-2006 VEHICLE WIRING VEHICLE WIRING REMOVAL

0

Filed Under (Toyota Manuals) by admin on 04-10-2011

download
IRING INFORMATION: 1984 Toyota Corolla FWD WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE OR WHITE/RED Ignition Harness STARTER WIRE BLACK/WHITE Ignition Harness IGNITION WIRE BLACK/YELLOW Ignition Harness SECOND IGNITION WIRE BLACK/ORANGE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness POWER DOOR LOCK (-) BLUE/WHITE Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) BLUE/RED Harness In Driver’s Kick Panel PARKING LIGHTS (+) DK. GREEN Harness In Driver’s Kick Panel PARKING LIGHTS (-) LT. GREEN Harness At Steering Column HEADLIGHTS (-) RED/WHITE Harness At Steering Column DOOR TRIGGER (-) RED/WHT OR BLK/WHT Harness At Fuse Box TRUNK TRIGGER COMMON WITH DOORS (Hatchback Only) TACHOMETER WIRE BLACK At Ignition Coil BRAKE WIRE (+) GREEN/WHITE Brake Pedal Switch HORN TRIGGER (-) GREEN/RED Steering Column LEFT FRONT WINDOW UP GREEN/BLACK At Driver Window Motor Inside Door LEFT FRONT WINDOW DOWN BLUE/RED At Driver Window Motor Inside Door RIGHT FRONT WINDOW UP GREEN Harness In Driver’s Kick From Driver Door RIGHT FRONT WINDOW DOWN BLUE/WHITE Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW UP RED/BLACK Harness In Driver’s Kick From Driver Door LEFT REAR WINDOW DOWN RED/YELLOW Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW UP RED/BLUE Harness In Driver’s Kick From Driver Door RIGHT REAR WINDOW DOWN BLUE/BLACK Harness In Driver’s Kick From Driver Doo

Incoming search terms:

Incoming search terms: