www howtocheckhisuntimingwithitassembled

You search Auto repair manual PDF www howtocheckhisuntimingwithitassembled, if there are search results will appear below. If search results do not exist, please search by others keyword.



  www howtocheckhisuntimingwithitassembled Direct Download speed 5282 Kb/s

  www howtocheckhisuntimingwithitassembled Full Version speed 6162 Kb/s



2003 Aprilia Tuono Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Remove the main seat and the passenger seat. 2. Prop the front of the fuel tank in the up position. 3. Route the PCIII harness from the trunk area towards the front of the bike. Route the PCIII harness under the fuel tank bracket (Fig. A). 4. Attach the ground wire from the PCIIIharness to the negative side of the battery. (fig. B). 5. Locate the Throttle Position Sensor on the backside of the throttle bodies (Fig. C). 6. Locate the BROWN wire with the YELLOWtracer and attach the supplied wire tap to the wire. NOTE: It is recommended to use dielectric grease on this connec- tion. Fig. A Fig. B Fig. C 2003 Aprilia Tuono – PCIII USB – 2 i907-411 www.powercommander.com Wire tap Ground wire from PCIII TPSI connector 7. Attach the grey wire from the PCIII to the wire tap (Fig. D). NOTE: It is recommended to use dielectric grease on this connec- tion. 9. Plug the YELLOWcolored wires from the PCIIIharness in- line of this connection. (fig. F) Fig. D Fig. E Fig F 2003 Aprilia Tuono – PCIII USB – 3 i907-411 www.powercommander.com Stock connector Grey wire from PCIII PCIII connectors Stock connector 8. Unplug the stock wiring harness from the rear injector (left hand side of the throttle body). Fig. E 10. Unplug the stock wiring harness from the front injector (right hand side of the throttle body). Fig. G 11. Plug the ORANGE colored wires from the PCIIIharness in- line of this connection

CL-1000 CONDOR CYCLE LOADER USER INSTRUCTION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Confirm that the cradle is set in the optimized position setting (See RECOMMENDED CRADLE SETTINGS) for the entering tire and wheel. Adjustment of cradle is crucial for optimum retention. Optimum retention is achieved by trying different settings. ( REFER TO CAUTION PARAGRAPH BELOW ): If the optimum vertical support is achieved, the motorcycle will hold itself upright. If optimum retention is not achieved try different cradle settings. ( REFER TO CAUTION PARAGRAPH BELOW ). Once cradle is positioned, tighten the brakes using the eye bolts and place the Cycle Loader in front of the motorcycle. Push or drive the motorcycle, centered into unit, until the cradle of the Cycle Loader has fully engaged the wheel. Once the wheel is cradled, proceed to push further into the Cycle Loader until the wheel has engaged the front stop. If the optimum vertical support is achieved, the motorcycle will hold itself upright. As an extra precaution, an optional Velcro strap may be used to strap the cradled wheel to the front stop (Optional Velcro strap purchased separately). Always strap Velcro through the wheel and around the front stop below the upper front stop flange. Loosen the brakes and use two (2) tie-down straps to secure the motorcycle to the two front eyebolts of the Cycle Loader. Hook wench to Ω” ‘U’ hook in front of Cycle Loader. Use the wench to pull the Cycle Loader with motorcycle up the flat bed. Once the motorcycle is all the way on the flat bed, the bike should be secured to the flat bed itself. For more information on use, refer to www.condor- lift.com. RECOMMEDED CRADLE SETTINGS: The Condor® Cycle Loader is designed so that for every tire/wheel size within the ranges specified a minimum of 2 cradle settings is suitable. **The optimum cradle setting for a specific tire would be, the setting that allows the cradle to tilt flush with the unit/ or º” below the opening in the main unit where the cradle sits, without touching.** The 2nd optimum setting would be the setting forward from the optimum setting away from the entry direction. If less retention is desired at any time due to too much retention or sticking, the cradle may be moved away from the entry direction one notch. RACING APPLICATIONS: For bikes with GP or low durometer front tires compounds, use the 5th cradle setting from the entry directions. CAUTION: Always make sure that all fasteners are tight and all pins are in place prior to use. Understand the limitations of this product and do not exceed these limitations. Always make sure that the unit’s cradle settings are optimum for the tire size of the motorcycle before use. For bikes with very low fenders and or cowlings, a custom cradle may be purchased fitted to specific tire sizes, so as not to make contact. For standard sport bike front wheel combinations, the 1, 2, 3, front settings may be suitable. If instructions are not clear, additional information is available at www.condor-lift. com or call 1-800-461-1344. Technical Components Development & Design is not responsible for any damage incurred by exceeding this product’s limitations in structure and/or functionality.

Hot-Start Kit For Yamaha YZ/ WR 400F

0

Filed Under (Yamaha) by admin on 16-12-2010

download
Blaster Rear Brake Kits 121-01298 • YFS200 Blaster ’88-’98 • This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper. 121-01299 • Same as 121-01298 +4″ • Cable is 4″ longer for extended swingarms. 121-01027 Replacement Ratchet Spark Plug Wrench 121-08147 • Designed specifically to fit where there is limited space • Ratchet mechanism works one way • Fits standard 13/16″ plugs
INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS R . 03-15-06 21 (626) 792-7384 www.FlandersCompany.com Fax: (626) 792-5341 www.FlandersCo.com Specialty Tools Swingarm Bearing Tool 121-080213 • Designed for installation of the swing arm bearings on late model Japanese motorcycles • Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm without beating on it with a hammer Main Jet Wrenches • High-quality die cast construction • 6mm round and hex jets and 8mm round • Cap holds a few spare main jets • Sold each 121-08023 6mm Hex (Fits 6mm hex main jets) 121-08024 8mm Round (Fits 8mm round main jets) 121-08025 6mm Round (Fits 6mm round main and pilot) Allen Extension 121-080184 • 5mm allen on a 6.25″ long, 3⁄8-drive extension for hard-to-reach case bolts • Designed for use with air tools • Great for splitting engine cases

2010 Harley Davidson Touring Model Power Commander Installation manual

0

Filed Under (Harley Davidson) by admin on 29-02-2012

download
1 Remove the stock seat. 2 Unplug the stock wiring harness from the ECM (Fig. A) . 3 Plug the PCV connectors in-line of the stock ECM and wiring harness (Fig.B). 4 Tuck the PCV to wiring harness connection into the opening in front of the battery box (Fig. C). 5 Using the supplied velcro attach the PCV to the top of the ECM (Fig. C) FIG.A FIG.C Remove Ground wire FIG.B PCV connector PCV connector Stk connector Connection 15-011 www.powercommander.com 2010 Harley Davidson Touring PCV – 4 6 Remove the right hand saddlebag and sidecover. 7 Locate the stock O2 sensor connections and unplug both connectors (Fig. D) The stock O2 sensors will NOT be connected to anything at this time. The sensors can be removed from the exhaust if you have a way to plug the hole. Unplugging the sensors does NOT cause an engine light but will cause a historic code in the ECM for non-active O2 sensor. This is not causing any issues with the running of the bike. FIG.D Follow these instructions when using the Auto tune kit – part #AT-100B 1 Remove the left hand side cover. 2 Place the Autotune modules in front of the battery as shown in Figure H. If using velcro make sure the velcro does not cover the designation of the unit on the back (AT #1 or AT#2). The modules are coded to the front and rear cylinders. FIG.E 3 Remove the rubber plug for the diagnostic connector. Plug the lead from the Autotune kit into the stock diagnostic connector (Fig. J).This connection is under the LH sidecover. DO NOT connect to the accessory connection in front of the battery. 4 Reinstall the sidecover. FIG.F 15-011 www.powercommander.com 2010 Harley Davidson Touring PCV – 5 5 Connect the longer harness to the front O2 sensor. Route the harness along the front down tube and along the backbone of the frame to Autotune module AT#1. Wire the harness to the module per Figure G. The harness can be cut to length if desired. 6 Repeat step 4 for the rear cylinder. Wire the harness to Autotune Module AT#2. The harness can be cut to length if desired. If your exhaust does not accept the M18x1.5mm O2 sensor you will need to install the supplied O2 bungs with the Auto tune kit into your exhaust. See Auto tune instructions for more information

1999-2004 Kawasaki 1500 Drifter Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 Remove the seat. 2 Remove the left side cover. 3 Remove the speedometer assembly. 4 Unbolt the fuel tank. NOTE: It is not necessary to remove the fuel tank. It does however make the installation easier. If you do remove the tank, pay attention to the vent hose routing. Pressing the tabs on the black fuel line connector will allow the fuel line to be disconnected (Fig. A) 5 Remove the battery/ECU hold down bracket (Fig. B). 6 Unbolt and move the bank angle (tip over) sensor out of the way (Fig. C). Fig. A Fig. B Fig. C i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 2 Bank angle sensor (tip over switch) Remove these 2 bolts 7 Loosen the bolts holding the plastic tray on the left side of the bike (under the left side cover) (Fig. D). 8 Route the wire from the PCIII behind the plastic tray and under the frame side rail (Fig. E). 9 Retighten the bolts holding the plastic tray. 10 Continue routing the wires from the PCIII under the frame near the lower fuel tank mount and go up to the throttle body area (Fig. F). Fig. D Fig. E Fig F i201-411 www.powercommander.com 1999-2004 Kawasaki 1500 Drifter – PCIII USB – 3 Route PCIII harness between plastic tray and frame Route wires under frame Loosen these bolts 11 Disconnect the injector connector from the rear injector (Fig. H). 12 Plug the female PCIII connector with ORANGE/WHITE wire onto the rear injector (Fig. H). 13 Connect the male PCIII connector with ORANGE wire onto the stock injector connector (Fig. H). 14 Repeat steps 11 thru 13 for front injector using the PCIII connectors with the YELLOWcolored wires. 15 Locate the wires coming from the throttle position sensor. (Fig. H). The throttle position sensor is located on the right hand side of the throttle body. It is between the frame and engine

Incoming search terms:

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

2003-2004 Kawasaki VN1600 Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 Remove the main seat and the passenger seat. 2 Remove the fuel tank Note: The installation can be done without removing the fuel tank but it may be easier to have it removed 3 To remove the fuel line squeeze the sides of the connector (Fig. A). Disconnect the two electrical connectors. 4 Loosen the four bolts holding on the left hand side cover (Fig. B). 5 Route the PCIII harness between the tray and the frame (Fig. C). Fig. A Fig. B Fig. C i209-411 www.powercommander.com i209-411 www.powercommander.com 2003-2004 Kawasaki Z1000 – PCIII USB – 2 Disconnect these lines Squeeze this line to remove Loosen these bolts PCIII harness 6 Continue routing the PCIII harness towards the front of the bike. Route underneath the frame and towards the left hand side of the rear cylinder (Fig. D). 7 Continue routing the PCIIIhar- ness along the frame towards the front of the bike. Locate the stock connector for the throttle bodies (Fig. E). 8 Unplug this connector. 9 Plug the connectors from the PCIII in-line of the stock connector (Fig. F)

Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Harley Davidson 6- SPEED CONVERSION KIT FOR BIG TWIN 5- SPEED TRANSMISSIONS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
5/16 Bolt hole boss clearance This can easily be checked with the trap door gasket. Put the gasket on the dowel pins. AII material of the boss around the hole that “sticks outside” the gasket (60 degrees forward to 60 degree backwards) must be removed (see figure A). Primary fork clearance Place the gasket on the housing and remove material as indicated for clearing the shifter fork (see figure B). WWW . ZODIAC . NL PERFORMANCE PRODUCTS FOR HARLEY-DAVIDSON ® INSTALLATION INSTRUCTIONS FOR 6 SPEED CONVERSION KIT AND 6 SPEED BUILDER KIT speed transmission. Also make sure you have a 1990 or later Factory Service Manual available. Tools The conversion kit should only be used in new or low milage transmissions. If gears or bearings of a used Gear set Removal Refer to the Factory Service Manual Section for Mainshaft and Countershaft removal. When you get to the point of actually sliding the gear set out make sure you properly mark the 5th gear set as described in the Factory Service Manual (for used transmissions only). Further follow the factory removal procedure. Clearance Checks The 6 Speed conversion and builder kit will fit in most OEM or aftermarket transmission housings without may be needed. The following clearances must be checked before assembling the 6 speed transmission. 28-05-2008 We recommend the kits are installed by a qualified mechanic with knowledge of the Harley-Davidson 5 needed are the same as used for a 5 Speed transmission. 5 speed transmission are worn, new ones must be installed, or better, the builder kit should be used. any modification of the housing. However due to casting differences, in some instances some modification
WWW . ZODIAC . NL PERFORMANCE PRODUCTS FOR HARLEY-DAVIDSON ® Pillow block clearance (right side) Make sure there is clearance between the pillow block and the housing. Any clearance is O.K. (see figure C). Fork shaft support clearance Again use the gasket as the template and remove the material as indicated (see figure D). Shift drum end play The end play of the shift drum must be checked prior to final installation. Install the shift drum. Measure the end play with feeler gauges at the right pillow block (see figure E). End play should be between .004″ and .010″, some 1/2″ X 7/8″ 0.008″ thick shims are included to adjust the end play

Incoming search terms:

HARLEY DAVIDSON 2008-2009 FLHR, FLHRC, FLHT, FLHTC FLHTCU, FLHX, FLTR 1584CC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Start the engine with the transmission in neutral or park. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, fi nd cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fi x as necessary. 3. If road test is fi ne, you can now enjoy the added power and performance from your kit. 4. K&N Engineering, Inc., suggests checking the air fi lter element periodically for excessive dirt build-up. When the element becomes covered in dirt (or once a year), service it according to the instructions on the Recharger® service kit, part number 99-5050 or 99-5000. ROAD TESTING: • 1455 CITRUS ST., P.O. BOX 1329, RIVERSIDE, CA., U.S.A. 92502 • TECH SERVICE 800-858-3333 • FAX 951-826-4001 • e-mail: tech@knfi lters.com® • WWW: http://www.knfi lters.com® 10. Install the provided K&N® air fi lter and secure with the provided hose clamp. A black hose clamp is being supplied with kit. This clamp is intended to clamp the fi lter to the intake tube. NOTE: The K&N® high fl ow intake system is a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must install the K&N® Drycharger® onto the air fi lter.