x nxx e2 80 8e 1957 trike engines

You search Auto repair manual PDF x nxx e2 80 8e 1957 trike engines, if there are search results will appear below. If search results do not exist, please search by others keyword.



  x nxx e2 80 8e 1957 trike engines Direct Download speed 5282 Kb/s

  x nxx e2 80 8e 1957 trike engines Full Version speed 6162 Kb/s



YAMAHA ROADSTAR TRIKE Removal of Clear Taillights and installation of Red Taillights

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1 Installation of Lights 1.1 Support the trike on jack stands and remove the wheels. 1.2 Remove the clear lights from the inside of the wheel wells by unscrewing the three (3) screws from the light. 1.3 Unplug the wires and remove the lights. 1.4 Remove the chrome bezels and rubber gaskets from the clear lights and install on the red lights (5 screws). 1.5 Re-connect the wire plugs and install the red lights to the trike body using the same three screws. 1.6 Replace the wheels and torque the lug nuts to 75 lb.ft. 2 Wire modification inside trunk 2.1 From the inside of the trunk pull back the carpet on both the left and right hand sides to expose the wire harnesses coming from the wheel wells. 2.2 Locate the resistors in the harness, 2.5″ x 0.5″ x 0.5″, and covered by black shrink wrap. 2.3 Cut the shrink wrap to expose the resistors and cut wire on both side of the resistors. Remove and discard resistors. 2.4 Splice in the supplied 5″ green wires (WITHOUT the diodes) with 2 blue scotchlock connectors per side to reconnect the cut wires. 2.5 Do not glue in carpet until lights are tested. 3 Change to pigtail from Trike to Motorcycle. 3.1 Remove driver’s sear 3.2 Unplug pigtail from motorcycle (MC) wiring and trike body wiring. 3.3 Cut heat shrink on the MC plug side of the pigtail and pull expansion sleeve back to expose the wires. Figure 1 3.4 Cut Green and Yellow turn signal wires and about 3″ from the MC plug and splice in Green and Yellow wires from the supplied resistors with the supplied hest shrink solder connectors (heat to be applied) – (three wires in one connection) Figure 1 3.5 Cut the Red (Brake) and Brown (Running lights) wires and splice in the supplied diodes with the supplied heat shrink solder connectors. Red side of the diode wire facing the Trike plug. Figure 1 3.6 Connect eye lug on the black wire from the resistors to the negative terminal of the battery. Figure 2 3.7 Plug pigtail back into the Trike body and the MC

Incoming search terms:

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

Yamaha Road Star TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride

Incoming search terms:

HONDA VTX 1300 AND 1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 17-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or spline are fitted with grease fittings, pump the fittings with wheel- bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight)

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

1945-1957 AJS Pitmans Installaiton Manual

0

Filed Under (AJS) by admin on 31-10-2010

download
AN A.J.S. O.H.V. single is easy to handle, and even the absolute novice quickly acquires confidence in the saddle. Beware, however, that you do not indulge in big throttle openings until you have had ample road experience. Also do not forget to digest the Highway Code. FIG. 1. A FLEXIBLE AND FAST TOURER WITH CLEAN LINES AND MECHANICAL QUIETNESS – THE 1957 MODEL 18S The 500 c.c. A.J.S. model shown is similar to the 350 c.c. model 16MS. Both models have snappy push rod O.H.V. engines with light-alloy cylinder heads, “Monobloc” carburettors, hairpin valve-springs, and automatic-ignition control. Their specification includes: “Teledraulic” front forks, Girling rear-suspension units, a quickly detachable rear wheel, die-cast light-alloy hubs, a deep secondary-chain guard, a new A.M.C. four- speed gearbox, Lucas headlamp, twin pilot-lights, and other attractive features. * The A.J.S. engine and frame numbers required on Form R.F. 1/2 will be found on the near-side of the crankcase and the off-side of the saddle lug, or on the off-side of the front down-tube (later models). THE BOOK OF THE A.J.S. 1 Essential Preliminaries. Before you can legally ride on the road – (1) Insure against all third-party risks and obtain the vital “certificate of insurance.” With a new machine you cannot get this until the machine is licensed, and an insurance “cover note” must be obtained. If you have a valuable machine, you are advised to take out full comprehensive insurance. (2) Obtain the registration licence and registration book (Form R.F.I/2)* or renew the licence (Form R.F. I/A). (3) Obtain a three-monthly “provisional” or an annual driving licence (Form D.L.I).* (4) Fit a reliable speedometer if one is not fitted (not essential if machine registered prior to 1st Oct., 1937). (5) If you carry a pillion-passenger, see that he or she sits astride a proper pillion seat securely fixed to the machine (all “springers” have dualseats), and that the passenger holds a current annual or substantive driving licence for Group G if you are a “learner.” (6) If you are ineligible for an annual or substantive driving licence, attach “L” plates to the front and back of the machine. (7) If not already provided, fit a red reflector (1½ in. minimum diameter) vertically at the rear of the motor-cycle and, on a sidecar outfit, an additional red reflector and rear lamp at the rear of the sidecar and at the same height as those on the motor-cycle. (8) Use an ignition-suppression type sparking plug or terminal cover if the machine was registered for the first time after 1. st July, 1953. All the official forms referred to above may be obtained from any money-order post office. See also footnote **, with reference to Forms R.F, 1/A or R.F. 112. You are not eligible for a substantive driving licence for Group G unless you are 16 and have complied with one of these conditions- (a) You have held a licence (other than a provisional or Visitor’s licence authorizing the driving of vehicles of the class or description applied for within a period of ten years ending on the date of coming into force of the licence applied for. (b) You have passed the prescribed driving test (this includes a test passed while serving in H.M. Forces) during the said period of ten years

Honda VTX 1300 Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 27-10-2010

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model. Honda VTX 1300 TRIKE CONVERSION CHAMPION TRIKES Installation Manual Page 7 of 16 Revision 2 3 Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black

Incoming search terms:

Harley-Davidson Twin Cam Engines Cam Chain Drive System Installation and removal MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
Removing the Cam Chain Drive System. NOTES Changing camshafts and cam drives in the 2006-up Harley-Davidson® Twin Cam 88® engines is different than in pervious engines. Procedures require use • of some special tools. Installation should be done by an experienced mechanic with access to factory service manual and required tools. Tighten all fasteners to the correct specifications and in order described. Always use an accurate torque wench. • Incorrect installation can cause engine damage not covered under warranty. CAUTION Failure to install components correctly can result in sudden engine seizure. Engine seizure may result in serous injury to motorcycle operator, passenger, or others. A- Disconnect the battery ground cable to eliminate potential sparks and inadvertently engagement of the starter while working on the motorcycle. B- Remove spark plugs and pushrod cover clips. Collapse the pushrod covers to expose the pushrods. C- Safely elevate and stabilize the rear of the motorcycle. Place the transmission in high gear. Turn the rear wheel to rotate the engine until both lifters and pushrods for either cylinder are at the lowest point on the camshaft (TDC of compression stroke). Both intake and exhaust pushrods for that cylinder will be under pressure from the valve springs and will rotate with light finger pressure. NOTE: 510G camshafts may use stock style non-adjustable pushrods instead of adjustable pushrods. If installing non-adjustable pushrods, disassemble and assemble rocker boxes per H-D® instructions. All other S&S® gear driven cams require installing adjustable pushrods. As a time-saving measure, the stock pushrods can be removed with bolt cutters. Be sure to head caution and warnings of these instructions. D- Cut the pushrods for the cylinder that is at TDC with the bolt cutter and remove the pushrod covers from the engine. Rotate the engine to place the pushrods for the other cylinder at their lowest point. Cut and remove the remaining pushrods. WARNING CAUTION Cutting pushrods with a saw or cutoff wheel may result in debris entering the engine, causing engine damage not covered under warranty. WARNING Cutting pushrods without releasing spring pressure, by rotating the engine until tappets are at the lowest point of travel can result in bodily injury. E- Remove the pushrod covers and lifters form the crankcase. F- Remove engine cam cover and gasket. Secure lifers with a tool made from a large binder clip

Incoming search terms:

Harley-Davidson Twin Cam Engines Performer RPM Gear Drive Camshaft Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 03-03-2012

download
1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 INSTALLATION PROCEDURE 1. Disconnect the battery, and remove the fuel tank. 2. On engines with the oil tank above the engine, drain the engine oil. 3. Remove the front exhaust pipe to clear the Cam Housing Cover. 4. Remove the Rocker Covers and remove the four 5/16″ bolts and the two 1/4″ bolts holding the rocker arms in place. With the rocker arms removed, remove the stock pushrods. 5. Remove the push rod tube retaining clips and push rod tubes. 6. At this point, you may remove the lifter covers and take the lifters out, or you can make a lifter holding tool from a binder clip as shown in Figure 1 . 7. On pre-2000 models with a cam position sensor, you may want to remove the inspection cover, unplug the wires, and remove the sensor at this time to ease installation later on. 8. Remove the cam housing cover keeping the bolts in a separate cup. ( Note: Oil will run out of the cam housing.) 9. Using the Chain Tensioner Unloader Tool, unload pressure on the outside chain tensioner, and pin it in place with the retaining pin (See Figure 2) .

Incoming search terms:

HARLEY-DAVIDSON Sportster Solid Axle Suspension Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 24-26psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential, and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” approximately ¾”-1″ with a new belt or 1″ to 1-1/2″ with a used belt of total vertical movement. Do not use commercial belt dressing compounds on the belt except for Harley Davidson Poly-Oil, PN 99860- 81. These compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension is a “Zero Flex” solid axle with high performance adjustable pre-load coilover shocks. The suspension system is designed to give you the best ride with a load of no more than 400 pounds. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

Incoming search terms:

Incoming search terms: