xr100 oil cooler install

You search Auto repair manual PDF xr100 oil cooler install, if there are search results will appear below. If search results do not exist, please search by others keyword.



  xr100 oil cooler install Direct Download speed 5282 Kb/s

  xr100 oil cooler install Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

YAMAHA ROAD STAR WARRIOR OIL COOLER KIT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
INSTALLATION: 1. See FIG. F: Apply a thin film of oil to O-RING (#9) on OIL COOLER MOUNT ADAPTER (#2). Install the OIL COOLER MOUNT ADAPTER with OIL COOLER SUMP STUD (#6). Note that o-ring on adapter is mounted against oil filter sump. TIP: Only tighten “finger tight” at this point so adapter can move as needed to adjust oil lines. 2. See FIG. G: Install OIL LINES (#3 & #4) to OIL COOLER and OIL COOLER MOUNT ADAPTER as shown. Do not tighten fittings yet. NOTE: The shorter 9-3/4″ OIL LINE will be on the TOP fitting on the ADAPTER. 3. See FIG. H :Install OIL COOLER to frame with the BILLET OIL COOLER CLAMP (#7). Adjust OIL COOLER to desired position and tighten the three 10-24 X 1/2 SOCKET HEAD SCREWS (#8) securely. Rotate the OIL COOLER MOUNT ADAPTER as necessary to align the Oil Lines properly. WARNING: Make sure OIL COOLER is moved outward far enough so that it does not contact the Front Fender when the fender goes through its full range of motion! 5. See FIG. I & J: Tighten the AN fittings on the OIL COOLER MOUNT ADAPTER as shown with an 11/16″ open end wrench. Tighten the AN fittings on the OIL COOLER with an 11/16″ open end wrench. TIP: To prevent the OIL COOLER from turning when the fittings are tightened, place a thin screw driver or long allen wrench between the fittings as shown. NOTE: DO NOT USE ANY SEALANT ON AN FITTINGS! 6. See FIG. K : Tighten OIL COOLER SUMP STUD (#6). Re-install oil filter. Start the engine and check for leaks. Check oil level and top-off as necessary. MAINTENANCE:

Incoming search terms:

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

Incoming search terms:

HARLEY DAVIDSON TOURING OIL COOLER KIT AND CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION 1. See Figure 1. Remove the spin-on oil filter (2) and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter adapter. NOTE The oil adapter assembly has two flanges protruding out of the back. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 2. See Figure 2. Install the oil adapter gasket (3) onto the oil filter adapter assembly (1). The oil adapter assembly flanges should be aligned so they are installed into the oil adapter gasket cutout as shown. 1 2 is00602 1. Oil filter adapter 2. Oil filter Figure 1. Oil Filter and Adapter 1 2 3 5 4 is00761a 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket 4. Gasket adhesive side 5. Oil cooler adapter assembly gasket surface Figure 2. Install Oil Adapter

HARLEY DAVIDSON CHROME OIL COOLER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 6 2 1 3 5 4 is04287a 1. Oil Cooler 2. Guard 3. Stock Washer 4. Stock Nut 5. Mounting Bracket 6. Area to Apply Heat Figure 1. Oil Cooler Preparation Be sure to follow manufacturer’s instructions when using the Robinair Heat Gun or any other radiant heating device. Failure to follow manufacturer’s instructions can cause a fire, which could result in death or serious injury. (00379a) 1. See Figure 1. Remove the oil cooler guard (2) from the oil cooler (1) by using the Heat Gun (or equivalent) to apply heat to the top surface. Pull the guard away from the oil cooler and discard. 2. Remove and discard the three locknuts (4) and flat washers (3) fastening the oil cooler to the mounting bracket (5). 3. Raise the oil cooler slightly to separate the studs on the underside of the oil cooler from the mounting bracket. 4. See Figure 2. Place the oil cooler cover (1) onto the oil cooler studs, between the oil cooler and the mounting bracket. 5. Lower the oil cooler and cover into the holes in the mounting bracket. 6. Place a new flat washer and locknut from the kit onto each stud. Line the oil cooler cover up squarely against the oil cooler, and tighten the locknuts to 80-100 in-lbs (9.1-12.4 Nm) . SERVICE PARTS

BMW Motorcycle R1100 RT R1100 RS R850/ 1100 GS R850/ 1100R Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Engine Connection Nm Nm Oil filter Oil filter 11 11 Oil drain plug 32 32 Oil pump Mesh filter basket to engine block 9 9 Oil pump cover 9 9 Pressure relief valve 35 35 Oil pressure switch 30 30 Oil cooler Oil cooler pipe to engine block 10 10 Cooling oil line – banjo screw 25 25 Cooling oil line – banjo screw with oil vent valve 25 25 Oil lines to oil cooler 25 – Oil cooler to holder 9 9 Oil cooler return line to engine block 35 35 Oil cooler feed line to frame 20 20 Oil cooler feed line to engine block 25 25 Screw-in union for oil cooler connection at engine block 35 35 Clean threads and apply Loctite 603 to inner and outer threads and in the contact face area Oil cooler hose at oil thermostat – 40 Cylinders Tightening sequence M 8 screw 20 20 M 6 screw 9 9 Chain guide rail pivot screw 18 18 Timing chain Chain tensioner 32 32 Connecting rod Big end cap Joint torque 20 20 Additional wrench angle 80° Crankcase Tightening sequence: M 10 screw (oiled) 45 45 M 8 screw (oiled) 20 20 M 6 screw Engine electrical system Connection Nm Nm Starter motor to engine 20 20 Starter cover to gearbox housing 7 – Positive lead to starter motor 10 10 Alternator to alternator support cover 20 20 Tensioning and retaining strap at alternator 20 20 Spacer at alternator 20 20 Positive lead to alternator 15 15 Belt pulley at alternator 50 50 Belt pulley to crankshaft 50 50 Poly-V belt preload 8 8 Spark plug 20 20 13 Fuel preparation and control Temperature sensor on engine block 25 25 16 Fuel tank and lines Fuel tank to rear frame 22 22 Fuel pump assembly to tank 6 6 18 Exhaust system Muffler to footrest 35 35 Manifold to cylinder head (with strap) 22 22 (with jacket pipe) 18 18 Muffler to support plate for center stand 20 20 Clip on muffler 50 50 Grease clamping face with Never Seez Oxygen sensor (lambda probe) to muffler 55 55 Grease with Never Seez

harley davidson oil filter cooler installation instructions

0

Filed Under (Harley Davidson) by admin on 10-04-2012

download
2000 cH ROME 99 – 07 SOFTAIL MODELS #2001 CHROME 99 – 07 DYNA MODELS #2002 CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2005 black CHROME 99 – 07 SOFTAIL MODELS #2006 BLACK CHROME 99 – 07 DYNA MODELS #2007 black CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2020 REPLACEMENT OIL FILTER #’S: 2000, 2001, 2002, 2005, 2006, 2007 1. See Figure 1 to verify all Feuling components and the proper mounting bracket for your model 2. Wash, clean and inspect all new Feuling hardware, Including – off-set sandwich oil filter adapter, filter cooler housing and oil lines, use compressed air to blow dry the oil lines, fittings, threads and bolt holes. Use a tap and die if needed to clean threads. (On installation use lubrication on all fasteners and fittings) 3. Refer to the proper service manual for your model motorcycle & engine, for removal of engine oil and spin-on oil filter. Dispose of these items properly. 4. Clean engine case oil filter spigot and sealing surface thoroughly. 5. Install the clean Feuling off set oil filter sandwich adapter; both O-ring and gasket need to be assembled dry. 6. First install the inside half of the off-set oil filter adapter, O-ring side towards engine case filter mount. We recommend using a dab loctite on the 1″ lock nut. (See figure 2) It is recommend to mock up the sandwich adapter before torquing nuts and bolts to obtain desired orientation and proper clearance to engine case and frame rails. 7. Install the fittings and oil lines onto the outer half of sandwich adapter torque fittings to proper specs using thread sealant on the 1/8 NPT threads and engine oil on the -4 AN oil line fittings. 8. Complete installation of sandwich adapter, including the inner gasket. Finger tight the allen head bolts in an alternating sequence on both sides before final torque. Re-Torque the allen head bolts after the first heat cycle after installation and during every oil change.

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Incoming search terms:

Triumph Oil Filter Mount installation

0

Filed Under (Triumph) by admin on 29-10-2010

download
The Norton filter adapter is then bolted to the rear piece, oil hoses are added, an oil filter is screwed into place, and the assembly is offered to the bike. With the bike supported by straps up on a lift, it will be easy to loosely mount the front clamp section in place and slide the whole assembly up the frame tube. In order to miss the center stand, the filter will need to be as high as possible without the grease nipple striking the top of the adapter. As it ends up, there is “sweet spot” where both the nipple and the stand miss the oil filter by about an 1/8 inch. Tighten the mount down when you find that place. I found that the Norton filter adapter is best plumbed using 5/16 ID black neoprene fuel hose. The spigots on the adapter are 3/8 inch, but it is better to stretch the hose over these that to use easier fitting 3/8 ID hose and then try to shrink it onto the Triumph’s smaller metal oil lines. There will simply be fewer oil leaks using the smaller hose. Be sure that you plumb the filter into the oil line that returns engine oil back to the oil tank. The Triumph oil pump cannot be counted on to create enough vacuum to suction highly viscous motor oil through a very fine filter during cool temperatures. Trying to place the filter on the oil line feeding the engine will quickly result in massive engine damage. It is always better to have the oil pump pushing oil through the filter, and the only way to have RF Whatley, Suwanee, GA 5 Jan 2008 that is to use the return oil line. On all “unit-construction” Triumph engines, the rear-most oil port is the engine oil return. Other Notes • It is generally considered that adding an oil filter will at least quadruple the life of a British motorcycle engine. These motors, which were for the most part perfected in the 1950′s, were designed to run on the older non-detergent oils. In the original design, the oil tank was the oil filter since all particulate debris in the oil settled to the bottom of the oil tank as sediment. All modern engine oils are high-detergent and tend to inhibit the formation of sediment. Therefore most of the fine abrasive in the engine oil continues to circulate unless a filter is added.

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

Incoming search terms: