xrm motor accessory

You search Auto repair manual PDF xrm motor accessory, if there are search results will appear below. If search results do not exist, please search by others keyword.



  xrm motor accessory Direct Download speed 5282 Kb/s

  xrm motor accessory Full Version speed 6162 Kb/s



1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

Honda Motorcycle Digital Audio System Owner's Manual

0

Filed Under (Honda) by admin on 22-11-2010

download
Applicable portable audio unit A commercially available portable audio player with a stereo mini jack terminal can be connected to this accessory. (An attachment kit designed for the model is necessary to connect the portable audio player to this accessory.) American Honda Motor Co., Inc. recommends you use a shock-resistant portable audio player such as a flash-memory player (e.g. MP3, etc.) or an MD player equipped with sound skip prevention function. American Honda Motor Co., Inc. also recommends you always ride your motorcycle safely on paved roads, because sound skip can occur during riding on rough roads. Refer to the following instructions on storage and handling of the portable audio unit. This accessory is not designed to operate the portable audio unit connected to the accessory. Refer to the portable audio unit manufacturer’s Owner’s Manual for how to operate the portable audio unit and operate it accordingly. Note that the warranty of this accessory does not cover function and failure of the portable audio unit connected to the accessory 5 Storage of portable audio unit connected to this accessory After connecting the digital audio system, put the portable audio unit in a stable place where it does not interfere with riding the motorcycle (e.g. in the sold separately front pouch, tank belt pocket, etc.) in a place free from vibration as much as possible. Do not place the portable audio unit in your pockets or clothes while connected to this accessory. The portable audio unit can vibrate and contact other materials while riding, causing a sound skip. To prevent such skips, store the portable audio unit in a suitable place while protecting it from vibration and shock by covering it with cushioning material. (Protect the remote control and peripheral devices as well as the portable audio unit.) Any system failure and damage to the portable audio unit and its peripheral devices are not covered by the warranty of this accessory.

Incoming search terms:

Commonwealth of Massachusetts Registry of Motor Vehicles Motorcycle Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
DEFINITIONS MOTORCYCLE Any motor vehicle having a seat or saddle for the rider that is designed to travel with no more than three wheels contacting the ground, including any bicycle with a motor or driving wheels attached. MOTORIZED BICYCLE A pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty (30) miles per hour (mph) . OPERATION OF MOTORIZED BICYCLES Under Massachusetts law, mopeds fall into the category of “motorized bicycles”(with or without pedals) and are therefore regulated by the Registrar of Motor Vehicles. Individuals must have a valid learner’s permit or driver’s license to operate a motorized bicycle or moped. Mopeds must have automatic transmissions and cylinder capacities of no more than 50 cubic centimeters. In addition, mopeds must meet all federal motor vehicle safety standards and have maximum speeds of no more than 30 mph. The following limitations apply:  Individuals may not operate at speeds greater than 25 mph;  Individuals may not operate on state highways or limited- access roads with signs prohibiting bicycles;  Individuals may not operate on off-street recreational paths;  Individuals may use bicycle lanes along roadways;  Individuals must use the proper hand signals before stopping or turning;  Individuals and their passengers must wear United States Department of Transportation (US DOT) approved helmets when operating;  Individuals may not carry passengers while operating on a permit.

TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

Incoming search terms:

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

HARLEY DAVIDSON CHROME ON/OFF SWITCH CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Models WITH maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 1 2 is0771a 1. Auxiliary accessory housing cover 2. Cover screw (2) Figure 1. Auxiliary Accessory Housing 2. ALL models: If the Auxiliary Accessory Housing Kit and the Rocker Switch(es) ARE NOT already installed on the motorcycle handlebar: a. Proceed to Step 3 of these instructions. Install a chrome switch cap onto each switch before installing the Auxiliary Accessory Housing Kit onto the vehicle. If the Auxiliary Accessory Housing IS already installed on the motorcycle handlebar: a. See Figure 1. Using a T-25 TORX® driver, remove the two screws (2) retaining the Auxiliary Accessory Housing cover (1), and remove the cover. b. See Figure 2. Remove the switch mounting bracket, along with any attached switch(es) and accessories, from the switch housing. Note: it is not necessary to remove the switch from the mounting bracket, or to disconnect the switch wiring to replace the switch caps

HARLEY DAVIDSON BLACK ENGINE GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Be sure to locate and follow the procedures that apply to the motorcycle receiving the new guard. For Models without Lower Fairings 1. Proceed to For All Models section. For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Remove the lower fairings following the instructions in the appropriate Service Manual. 2. When the lower fairings have been removed, proceed to For All Models section. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley-Davidson Genuine Motor Accessory Lower Fairings 1. See Figure 1. Remove the two black screws (1) that attach the fairing cap (2) to the lower fairing (5). Remove the cap. Set the parts aside for re-installation. 2. Remove the screw (7), rubber washer (8) and locknut (10) and the clamp (9) that attaches the bottom of the lower fairing to the engine guard and set aside. 3. Remove the two locknuts (3), U-bolt (6) and U-bolt retainer (4). 4. Remove the lower fairing by sliding it out from behind the engine guard. 5. Repeat Steps 1 through 4 for the opposite side. 6. Proceed to For All Models section. For Model FLTR/I (Road Glide) with Harley-Davidson Genuine Motor Accessory Lower Fairings Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery, negative (-) battery cable first, following the instructions in the appropriate Service Manual. 2. Remove the seat following the instructions in the appropriate Service Manual. 3. Remove the cable strap holding the clutch cable to the engine guard. 4. See Figure 2. Remove the TORX screw (8), rubber washer (9) and locknut (11) and the clamp (10) that attaches the bottom of the lower fairing (4) to the engine guard and set aside INSTALLATION 1. Hold the engine guard in position, and loosely fasten the top of the guard with the new hex socket screw and flat washer from the kit. 2. Install the bottom brackets to the motorcycle frame with the two new TORX screws and locknuts. 3. Tighten all three screws to 15-20 ft-lbs (20.3-27.1 Nm) . For Model FLHTCUI (Ultra Classic Electra Glide) with Factory-Installed Lower Fairings 1. Install the lower fairings following the instructions in the appropriate Service Manual. For Models FLHR/I (Road King), FLHT (Electra Glide Standard) or FLHTC/I (Electra Glide Classic) with Harley- Davidson Genuine Motor Accessory Lower Fairings 1. Carefully place one lower fairing in position from behind the engine guard. 2. See Figure 1. Install the lower fairing to the top of the new engine guard with the U-bolt (6) from the back, through the holes at the top of the fairing. Install the retainer (4) in position on the U-bolt and secure to the engine guard with the two locknuts (3). Do not tighten the locknuts at this time. 3. Attach the bottom of the fairing to the engine guard with the clamp (9) removed earlier. Install the clamp around the engine guard in the direction shown, with the tabs toward the rear of the vehicle and the flat side of the clamp against the lower fairing. Insert the screw (7) through the lower fairing, rubber washer (8) and clamp (9). Secure the assembly with the locknut (10). Tighten to 12 ft-lbs (16.3 Nm) .

Incoming search terms:

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

BMW R1100RT, BMW R1150RT Signal Mirror Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
1. These instructions start with the right side mirror. Grab the mirror housing as shown and slowly push down to disengage housing from motorcycle. 2. Once you have the mirror housing removed partially, twist and remove the light bulb from mirror housing. Remove mirror housing and set it on a cloth covered surface. 3. Remove the factory mirror by inserting a slotted screwdriver against each mirror mount snaps. Slowly twist and pry each snap until it releases from motor actuator. Repeat process until factory mirror disengages. NOTE: Insert the slotted screwdriver as close to each of the snaps as possible before prying out the OE mirror. Not doing so may cause the crossbar on the motor actuator to break. Connect the two mating connectors from the adapter Signal® mirror wire harness and the new Signal® mirror wire harness. Cut a slot in the foam disc to accommodate the anti-vibration prongs on the motor adapter. Place the foam disc onto the center of the Signal® mirror motor interface. Connect the Signal® mirror mating connector to the Signal® mirror wire harness. 5. Remove Cap Sheet from two-sided adhesive disc on back of Signal ® mirror. Align the anti-rotation prongs found on the top and bottom or left and right with the corresponding slots on the motor mount. Use the palm of your hand, push down on the Signal® mirror and the mirror housing until the Signal® mirror motor mount is fully engaged. Note: Push firmly on all sides of the Signal® mirror to ensure proper engagement and travel. Not doing so could result in mirror falling off. 6. Locate the light bulb and carefully disconnect the original light blue with black stripe wire [hot wire]. Connect the red wire from the Signal® mirror wire harness to the spade terminal on the light bulb. Connect the original light blue with black stripe wire to the other spade terminal located on the red wire of the Signal® mirror wire harness. Repeat the process for the original brown wire and the black wire from the Signal® mirror wire harness [ground wires]. Insert the light bulb back into the mirror housing. 7. Align the 3-pins with their corresponding snap holes and snap the mirror housing into place. 8. Insert key into the ignition and turn to the “ON” position. Activate the right hand turn indicator to verify that the new Signal® mirror is working correctly. Replace any other accessories necess

Incoming search terms:

Incoming search terms: