yamaha 125 fork oil capacity

You search Auto repair manual PDF yamaha 125 fork oil capacity, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha 125 fork oil capacity Direct Download speed 5282 Kb/s

  yamaha 125 fork oil capacity Full Version speed 6162 Kb/s



HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HARLEY DAVIDSON FL SOFTAIL PROFILE LOW FRONT SUSPENSION KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-11-2010

download
Fork Spring Removal 1. Elevate and support the vehicle so the front tire is off the floor and the forks are fully extended. 4 9 3 1 10 11 2 5 6 7 8 is04004 1. Slider tube cap 2. Spacer washer 3. Oil seal 4. Clamp bolt and washer 5. Fork tube plug 6. O-ring 7. Fork spring 8. Tight-wound end of spring 9. Fork slider tube 10. Fork slider 11. Drain screw and washer Figure 1. Front Fork NOTE Remove the brake caliper from the fork slider. DO NOT remove the brake line from the caliper. 2. Remove the front wheel. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. 3. Remove the front fender. See FRONT FENDER in the Service Manual. 4. See Figure 1. Remove the slider tube cap (1), spacer (2) and oil seal (3) from the top of one fork side. Save the cap and spacer. The oil seal can be discarded. 5. Loosen the clamp bolt (4) and pull the fork from the brackets. 6. Repeat Steps 4 and 5 for the other fork side. -J00280 1 of 4 Wear saf ety glasses or gog gles when ser vicing f ork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) NOTE Be careful not to damage the O-ring. 7. See Figure 1. Remove the fork tube plug (5) and O-ring (6). Pull the spring (7) out of the slider tube (9). Remove the drain screw and washer (11), and drain the fork. Reinstall the drain screw and washer, and tighten to 52-78 in-lbs (5.9-8.9 Nm). 8. Repeat Step 7 for the other fork side. NOTE The Profile® Low Front Suspension Kit requires a different amount of H-D TYPE E FORK OIL than is listed in the Service Manual. NOTE Measure the oil level from the top of the fork tube with the fork spring removed and the fork fully compressed. 9. See FRONT FORK OIL in the Service Manual, but substitute the measures below. Fill the forks with Harley- Davidson TYPE E FORK OIL: • 1986 through 1999 models: •11.7 oz (345 cc) of oil, or •5.2 inch (132 mm) from top of oil level to top of tube. • 2000 and later models: •13.4 oz (396 cc) of oil, or •4.1 inch (104 mm) from top of oil level to top of tube. Fork Spring Installation 1. Insert a new Profile Low spring (7) from the kit into each slider tube (9), with the tight-wound portion (8) toward the bottom of the fork slider. NOTE Be careful not to damage the O-ring. 2. Install the fork tube plug (5) and O-ring (6) assembly into the slider tube and tighten securely. Be sure that one flat on each fork tube plug faces toward the inside of the fork. 3. Insert both fork side assemblies up through the slider covers, the fork stem and bracket, and the upper bracket. 4. Obtain two new oil seals (3), H-D Part Number 45733-48, and the spacer washers (2) and slider tube caps (1) saved earlier. Place an oil seal, followed by a spacer washer, onto each fork tube plug. 5. Insert the threads of a slider tube cap through each washer and seal, and into the fork tube plugs. Tighten to 40-60 ft- lbs (54.2-81.3 Nm). 6. Tighten the fork stem bracket clamp bolts (4) to 30-35 ft- lbs (40.7-47.5 Nm). 7. Install the front fender. See FRONT FENDER in the Service Manual. Install the front wheel and brake caliper. See FRONT WHEEL: FLSTC/FLSTF/FLSTN in the Service Manual. Jiffy Stand Removal/Installation 1. Move the jiffy stand to the retracted (up) position. Wear safety glasses or goggles when removing or installing spring. Spring tension can cause spring, attached components and/or hand tools to fly out which could result in death or serious injury. (00477c) 2. See Figure 3. Unfasten the jiffy stand leg spring (A) from the vehicle. Remove the hex bolt (B), lock washer (C), flat washer (D) and leg stop (E) from the threaded end of the jiffy stand leg. Discard the jiffy stand leg, but retain all other components. 3. Clean and inspect the jiffy stand attaching parts and mounting bracket for wear or damage. If parts replacement is necessary, refer to the Jiffy Stand section of your Service Manual for replacement procedures

Incoming search terms:

HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

YAMAHA ROAD STAR WARRIOR OIL COOLER KIT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
INSTALLATION: 1. See FIG. F: Apply a thin film of oil to O-RING (#9) on OIL COOLER MOUNT ADAPTER (#2). Install the OIL COOLER MOUNT ADAPTER with OIL COOLER SUMP STUD (#6). Note that o-ring on adapter is mounted against oil filter sump. TIP: Only tighten “finger tight” at this point so adapter can move as needed to adjust oil lines. 2. See FIG. G: Install OIL LINES (#3 & #4) to OIL COOLER and OIL COOLER MOUNT ADAPTER as shown. Do not tighten fittings yet. NOTE: The shorter 9-3/4″ OIL LINE will be on the TOP fitting on the ADAPTER. 3. See FIG. H :Install OIL COOLER to frame with the BILLET OIL COOLER CLAMP (#7). Adjust OIL COOLER to desired position and tighten the three 10-24 X 1/2 SOCKET HEAD SCREWS (#8) securely. Rotate the OIL COOLER MOUNT ADAPTER as necessary to align the Oil Lines properly. WARNING: Make sure OIL COOLER is moved outward far enough so that it does not contact the Front Fender when the fender goes through its full range of motion! 5. See FIG. I & J: Tighten the AN fittings on the OIL COOLER MOUNT ADAPTER as shown with an 11/16″ open end wrench. Tighten the AN fittings on the OIL COOLER with an 11/16″ open end wrench. TIP: To prevent the OIL COOLER from turning when the fittings are tightened, place a thin screw driver or long allen wrench between the fittings as shown. NOTE: DO NOT USE ANY SEALANT ON AN FITTINGS! 6. See FIG. K : Tighten OIL COOLER SUMP STUD (#6). Re-install oil filter. Start the engine and check for leaks. Check oil level and top-off as necessary. MAINTENANCE:

Incoming search terms:

Street Fork Spring Installation Instructions

0

Filed Under (Tips and Review) by admin on 13-02-2011

download
1. Remove fork springs according to instructions contained in your shop manual. For maximum performance we highly recommend that the forks be thoroughly cleaned, inspected and new fork oil installed. Note: If your motorcycle comes equipped with two fork springs in each leg (long & short), remove and discard both springs and the flat washer between the springs. If a stock spacer exits, remove it. If there is a short spring on the damper rod, do not remove it! 2. Use the recommended fork oil viscosity as noted in your owners manual with the following exceptions: GL1100 20 weight, GL1200/1500 15 weight required. See fine tuning for more in- formation. Fork oil level/volume should be checked according to the steps outlined in your authorized shop manual. Measurement of your fork oil by level is the preferred method. However, some manuals only specify a volume measurement. Due to the design of a progressive wound fork spring it will displace more oil thus requiring a maximum oil level of 5.5″ (140mm). Caution: This is not a recommendation, it is only a precautionary statement. If your manual specifies an oil level higher than 5.5″ (140mm) set the oil level at 5.5″ (140mm). (Oil level is the distance from the top of the fork tube to the top of the oil with the fork completely collapsed and the fork spring removed see figure 1.) This measurement can be made by using either one of the Progressive Suspension Fork Oil Level Adjusters (FOL-1 or FOL-2). 3. Install your new fork springs into the forks. Mechanically, it makes no difference which way the springs are installed. Some manuals will state; install the spring with the close wound end towards the bottom. This is done because sometimes there will be less spring noise. The springs will perform exactly the same regardless of which direction they are placed. Check the spacer length requirement for your motorcycle in the enclosed supplement. If not listed, you must calculate the pre-load. What is pre-load? Pre-load is the distance the spring compresses when the fork cap is installed. You may or may not utilize a spacer to achieve proper pre-load. The spacer in itself is not “pre-load”. It just helps to achieve it. Why is pre-load important? It determines the proper ride height which in turn affects how the bike handles.

Incoming search terms:

YAMAHA DT125RE/ X SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
OIL WARNING LIGHT CHECKING METHOD Main Switch “ON” Gears in “NEUTRAL” Oil warning indicator light does not come on Refeer to CHAPTER 8 “SIGNAL SYSTEM” Oil warning indicator light come on Shift into gear Oil warning indicator light does not come on Oil warning indicator light come on Supply engine oil Engine oil level and electrical circuit are OK 1 CHK ADJ TRANSMISSION OIL LEVEL INSPECTION/ TRANSMISSION OIL REPLACEMENT 3-11 TRANSMISSION OIL LEVEL INSPECTION 1. Inspect: •transmission oil level Oil level low **Add sufficient oil ******************************** Transmission oil level steps: •Place the machine on a level surface. •Warm up the engine for several minutes and stop it. •Visually check the oil level through the level window *. NOTE: •Check the oil level just one minute after stopping the engine. •The oil should e confirmed between maximum *and minimum *marks. •If the oil level is lower, add sufficient oil to raise it to the proper level. •Do not add any chemical additives. Transmission oil also lubricates the clutch and additives could cause clutch slippage. •Be sure no foreign material enters the crankcase. **************** **************** TRANSMISSION OIL REPLACEMENT 1. Warm up the engine for several minutes. 2. Place a container under the engine. 3. Remove: •oil filler cap * •drain pulg * drain transmission oil. NOTE: Drain the transmission oil with the motorcycle slightly inclined to the right. 4. Inspect: •gasket (Drain plug) •O-Ring (oil filter cap) Damage **Replace

HARLEY DAVIDSON TOURING OIL COOLER KIT AND CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION 1. See Figure 1. Remove the spin-on oil filter (2) and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter adapter. NOTE The oil adapter assembly has two flanges protruding out of the back. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 2. See Figure 2. Install the oil adapter gasket (3) onto the oil filter adapter assembly (1). The oil adapter assembly flanges should be aligned so they are installed into the oil adapter gasket cutout as shown. 1 2 is00602 1. Oil filter adapter 2. Oil filter Figure 1. Oil Filter and Adapter 1 2 3 5 4 is00761a 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket 4. Gasket adhesive side 5. Oil cooler adapter assembly gasket surface Figure 2. Install Oil Adapter

Incoming search terms:

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

Incoming search terms:

Incoming search terms: