yamaha ag200 bike alternator modification

You search Auto repair manual PDF yamaha ag200 bike alternator modification, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha ag200 bike alternator modification Direct Download speed 5282 Kb/s

  yamaha ag200 bike alternator modification Full Version speed 6162 Kb/s



Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

Yamaha Road Star Motorcycles Trike Conversion Removal And Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model. nstallation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster plates. Figure 3 Qty per Assm Spec Description 2 M10 x 1.25 x 70 Hex Head Bolt 2 M10 x 1.25 Hex Nut b. Install adjuster plates to rear drive pinch blocks. Hardware installs from inboard to outboard side. Snug, but do not tighten hardware at this time. Figure 4

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

2007 YAMAHA ZX6RR GALFER Super Bike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 1 complete 3 line kit (front Kit), 1 single banjo bolt and 2 lower male adapters. There are also a total of 6 washers, 4 will be used, and 2 are spares. The Left hose has a locating clip and there is a new bolt to bolt that on. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. A: Right Caliper B: Please re-use stock routing clip for right line Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer male adapters, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. See Picture C

YAMAHA ROADSTAR/ WARRIOR ADJUSTABLE REAR LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Secure motorcycle to a bike lift and raise the motorcycle. Rear wheel should remain barely resting on the ground. 2. See diagram on page 2 for references made in parentheses, for example (#5). 3. Remove the nut from the rear suspension bolt (#5) at the bottom of the shock (#7). You may need to remove your exhaust and rear horn to access the nut and bolt. 4. Remove this suspension bolt (#5) from the non-exhaust side of the bike. You may need to raise or lower the bike to ease the tension on the bolt in order for it to come out. 5. Next remove the nut (#4) and bolt connecting the relay arm (#3) to the swingarm. From here remove the entire shock assembly and relay arm from the bike. For ease of re-installing the relay arm (Step 8) and shock be sure to take precautions that in removing the assembly, you can put it back the same way you took it off. Flipping of the relay arm can cause serious damage to the lowering kit and surrounding components. 6. Remove the two suspension arms from the relay arm(#3) and shock(#7). Compare stock arm to length of lowering arm you are about to install. Make sure the length of the lowering arm matches the link of the stock arm. To set how much you want to lower the bike, lengthen the lowering arms. Every 1/4″ longer than stock is approximately 1″ of drop. Do not lower the bike more than 2″ for safety reasons. To adjust, unscrew the large hex shaft from the threaded rods. Make sure to adjust length equally on both shafts. Be sure to tighten all jam nuts once desired lowering position is set. 7. Re-assemble the lowering arms to the top of the shock (#7) using the supplied collar, nut, and bolt. The stock collar (#6), the one in the eyelet at the top of the shock (#7), will need to be removed as it is too long. (This is because the heims are thicker than the stock arms) Do not tighten the nut, or re-install into the frame yet. 8. Re-install the relay arm (#3) to the swingarm. The large hex shafts go to the rear of the bike. This is where it

240 Sport Bike Swingarm Installation Instructions

0

Filed Under (Tips and Review) by admin on 02-12-2010

download
Motorcycles can be dangerous if not properly maintained and ridden safely. RC Components has no control over the usage of any of its parts. RC Components expects its customers to exercise good judgment as to the proper selection, installation, use, and maintenance of any parts. RC Components assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any parts in any way by any person. RC Components expects the end user to exercise good judgment. • Before installing this kit, read through these directions completely. This will familiarize you with the way in which the parts fit together and the tools needed to complete the job. • Before performing any installation steps, disconnect the motorcycle’s battery to eliminate any possibility of electrical damage or personal injury due to a short circuit. Part Number: NSTSB240 Page 2 of 12 Materials Needed: • Hardware Kit. Kit includes (See picture below): 04-05 GSXR750-600 & 03-04 GSXR1000 Kit Inboard Brake Kit Part Number: INSTSB240 Page 3 of 12 04-05 GSXR750-600 & 03-04 GSXR1000 Kit for Stock Caliper 08 Busa Kit for Inboard Brake Part Number: INSTSB240 Page 4 of 12 05-06 GSXR 1000 Kit for Inboard Brake
Part Number: INSTSB240 Page 5 of 12 05-06 GSXR1000 Kit for Stock Caliper 99-07 Busa Kit for Inboard Brake
Part Number: INSTSB240 Page 6 of 12 99-07 Busa Kit for Stock Caliper Tools Needed: • Bike Specific Service Manual (Refer to manual for all torque specs and tools that are not specified by RC Components.) • Assorted hand tools, metric and standard sockets and wrenches. • Hoist or other means to lift bike. • Torque wrench • Loctite, and anti-seize • Chain breaker • Bike specific sockets are required for some bikes. (Refer to factory service manual). • Die grinder (for chain to frame clearance on some models) Installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain

BMW R850, R1100, R1150, R1200 Oilhead Maintenance Manual

0

Filed Under (BMW) by admin on 16-11-2010

download
cold Engine and Drivetrain Procedures Check Alternator Belt Tools Parts T-handle hex – 4mm none Note: In most cases the alternator belt does not need to be checked any more. Early models should have the pulley and belt upgrade that came out a few years ago. Current recommendations are that the belt is installed and adjusted, then not disturbed until 36K when replacement is specified. 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Check the belt for cracks or shredding. 4. Check the belt tension, quite tight, ~1/4″ deflection when you press on the center. Note: Paul Glaves suggests that proper belt tension is when you can twist the belt ~90 degrees, midway between the pulleys. If you can twist it more than 90 degrees, it is too loose. If you cannot twist it 90 degrees, then it is too tight. 5. Leave the cover off for the valve adjustment procedure on the next page. Change Alternator Belt Tools Parts T-handle hex – 4mm alternator belt socket – 13mm ratchet wrench – 13mm torque wrench 1. Remove the four bolts holding the black plastic alternator belt cover at the front of the engine, 4mm T-handle hex. 2. Remove the cover by sliding it straight down. 3. Loosen the 2 nuts and 1 bolt, 13mm, that hold the alternator – one is on top and one is on each side, thus allowing the alternator to pivot down. 4. Remove the old belt. (Some bikes have a pipe that traps the belt – loosen it enough to get the old belt out and the new belt in) 5. Install the new belt being sure it is properly seated. 6. BMW calls for a tensioning torque of 5.9 ft.lb. (8 Nm) on the adjuster bolt on the left side of the bike. You have to get at this bolt from the alternator side and you may have to lift the tank. Alternatively, you can pry the alternator up with a large screwdriver to tension the belt. 7. Once the belt is under proper tension, tighten the 2 nuts and 1 bolt, 13mm, to 15 ft.lb. (20 Nm). 8. Check the belt for proper tension (see above) and proper seating alignment

Incoming search terms:

Incoming search terms: