yamaha gizzly 600 hose schematics

You search Auto repair manual PDF yamaha gizzly 600 hose schematics, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha gizzly 600 hose schematics Direct Download speed 5282 Kb/s

  yamaha gizzly 600 hose schematics Full Version speed 6162 Kb/s



Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

HONDA VTX1300 AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the rider and passenger seats, left chrome side cover & original horn located at the top of the radiator. 2. Locate the supplied black horn mounting bracket and supplied smaller hose clamp. Notice the slight twist in the bracket. Using 2 adjustable wrenches or a vise and one wrench remove the twist from the bracket. Route the hose clamp thru the bracket. (As shown in photo 1A) 3. Install the bracket on to the left frame tube, (As shown in photo 1A) and tighten securely. Bolt the supplied horns to the bracket using the supplied bolt, lock washer and nut, (As shown in photo 1) and tighten securely. Install the supplied trumpet covers (As shown in photo 1B) by flexing the spring clips over the trumpets. Check that they fit securely. If not remove covers, make sure the center screw is tight and bend spring clips in towards center of covers and re-install. Using a blade screwdriver pry the two supplied hoses with the “Y” connector off of the air horns cut a new piece of hose 3 ½” long from the hose and replace the short hose on the “Y”. Re-install the “Y” hose assembly with the short hose going on the long or upper trumpet. (See photo 1C) Re-route the original horn wires. (As shown in photo 1D) 4. From the supplied wire cut 2 pieces 28″ long. Strip ¼” of insulation from both ends. Crimp 2 supplied male terminals to one end and 2 supplied female spade terminals to the other end. Plug the male ends into the original horns wires. (As shown in 1D) Attach the remaining air hose to the “Y”. Tape the hose and wires together every 6-8″ using electrical tape to make routing easier and neater. Route the wires and hose up under the fuel tank, over the cylinder heads coming out between the frame rails at the rear of the fuel tank. (See photo 2A) Locate the supplied relay and plug the 2 wires from the original horn onto terminals 85 & 86 on the relay. (See wiring diagram on back of last page of instructions) This will be the 2 outer terminals that are parallel to each other. Locate the supplied fuse, holder & wire assembly. Crimp a supplied fork terminal to one end and a supplied female spade to the other. Attach the spade terminal to one of the remaining outer relay terminals. (#30 or 87 on wiring diagram) Remove the 3 Phillips screws from the battery top cover. Remove the cover and attach the fork end of the fuse wire to the positive (+) terminal. Re-install the battery cover. 5. Cut a wire 9″ long and strip ¼” insulation from each end, crimp a fork to one end and a female spade to the other. Attach this wire to the compressors negative (-) terminal. Cut another wire 18″ long and strip both ends. Crimp a female spade to both ends. Attach this wire to the compressor positive (+) terminal. Route the air hose out under the left side cover as shown in photo (3). Hold the compressor in place against the frame tube. Note: Looking at the large end of the compressor the space between the hose fitting and the bolt mounting flange forms a “V” shape. This is where the compressor should rest against the frame. Next loop the hose around to the compressor hose fitting and trim the hose to the desired length. Attach the hose to the compressor. Secure the compressor to the frame using 2 large supplied cable ties as shown. 6. (See photo 3A) Attach the compressor negative (-) wire to the bolt on the frame (As shown in photo 3B) Route the compressor positive (+) wire along the side up to the relay and attach to the remaining outer terminal 87 or 30. Cable tie the relay in place. (As shown in photo 2B) Use several of the supplied short cable ties to secure the compressor wires to the air hose (As shown in photo 3) as wells as any other loose wire or hose.

Incoming search terms:

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

Harley-Davidson Camshaft TC, EVO, Shovelhead, XL EVO, Iron Head, XR Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
EVO Black Widow PP8833-2 – 29 55 62 25 264 267 54 103 109 105.8 0.600 0.602 EVO Black Widow PP8826-2 – 27 61 63 29 268 272 56 107 107 107.0 0.602 0.602 EVO Black Widow PP8817-2 – 254 254 0.590 0.590 EVO Carl’s Speed Shop CM4 – 28 44 52 20 252 252 48 98 106 102.0 0.495 0.495 EVO Carl’s Speed Shop CM495F Y 19 47 50 16 246 246 35 104 107 105.5 0.495 0.495 0.179 0.168 EVO Carl’s Speed Shop CM580 – 19 47 50 16 246 246 35 104 107 105.5 0.580 0.580 0.194 0.163 EVO Carl’s Speed Shop CM612 – 36 60 68 28 276 276 64 102 110 106.0 0.612 0.612 0.277 0.235 88 EVO Carl’s Speed Shop CM660 – 38 62 68 28 280 276 66 102 110 106.0 0.660 0.660 0.314 0.277 90 EVO Carl’s Speed Shop CM774 – 284 284 0.784 0.784 0.277 0.236 EVO Carl’s Speed Shop CM780F – 34 70 74 30 284 284 64 108 112 110.0 0.774 0.774 103 EVO Crane EVR0020 – 31 64.5 77 23 275 280 54 107 117 112.0 0.608 0.589 88 EVO Crane Fireball 2000 Y -12 22 20 -10 190 190 -22 107 105 106.0 0.490 0.490 0.026 0.032 EVO Crane Fireball 300 Y 12 34 41 15 226 236 27 101 103 102.0 0.490 0.490 4000 EVO Crane Fireball 310 Y 16 40 43 19 236 242 35 102 102 102.0 0.490 0.490 1500 4500 75 EVO Crane Fireball 316 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane Fireball 326 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H286 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 2000 5000 80 EVO Crane H290 – 17 43 45 23 240 248 40 103 101 102.0 0.581 0.581 1800 5200 EVO Crane H296 – 24 48 57 25 252 262 49 102 106 104.0 0.490 0.500 2500 5500 EVO Crane H304 – 24 50 55 25 254 260 49 103 105 104.0 0.600 0.600 2500 5800 EVO Crane H306 – 28 54 69 23 262 272 51 103 113 108.0 0.500 0.510 0.224 0.195 3000 6000 EVO Crane H310 – 23 63 68 28 266 276 51 110 110 110.0 0.550 0.550 0.229 0.229 3000 6500 88 EVO Crane H314 – 26 54 65 21 260 266 47 104 112 108.0 0.600 0.600 2800 6000 EVO Crane HEV0042 – 27 59 71 23 266 274 50 106 114 110.0 0.600 0.576 0.226 0.194 3000 6000 100 116 EVO Crane HEV0067 – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 0.128 0.113 EVO Crane HEV0098 – 36 62 72 34 278 286 70 103 109 106.0 0.650 0.650 0.171 0.156 96 EVO CycleRama CR-E550 – 24 52 53 23 256 256 47 104 105 104.5 0.550 0.530 EVO CycleRama CR-E581 – 22 46 53 23 248 256 45 102 105 103.5 0.581 0.550 EVO CycleRama CR-E600A – 24 50 56 24 254 260 48 103 106 104.5 0.600 0.530 EVO CycleRama CR-E600B – 23 51 54 22 254 256 45 104 106 105.0 0.600 0.550 EVO CycleRama CR-E617 – 22 50 50 22 252 252 44 104 104 104.0 0.617 0.617 EVO CycleRama CR-E630 – 18 60 63 13 258 256 31 111 115 113.0 0.630 0.630 EVO CycleRama CR-E660 – 27 59 71 23 266 274 50 106 114 110.0 0.660 0.660 3500 6500 140 EVO Dave Mackie DM500 Y 22 38 52 12 240 244 34 98 110 104.0 0.500 0.500 0.189 0.138 EVO Dave Mackie DM500X Y 25 40 55 20 245 255 45 98 108 102.5 0.500 0.500 0.208 0.178 EVO Dave Mackie DM530 – 28 42 55 15 250 250 43 97 110 103.5 0.530 0.530 0.221 0.141 EVO Dave Mackie DM580 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 113 EVO Dave Mackie DM581 – 26 42 56 12 248 248 38 98 112 105.0 0.580 0.580 0.227 0.144 EVO Dave Mackie DM595 – 21 49 57 14 250 251 35 104 112 107.8 0.595 0.595 0.192 0.150 EVO Dave Mackie DM635 – 20 56 59 18 256 257 38 108 111 109.3 0.635 0.635 0.194 0.176 EVO Edlebrock 1740 Y 19 43 48 24 242 252 43 102 102 102.0 0.490 0.490 0.176 0.203 EVO Edlebrock 1741 – 20 46 52 22 246 254 42 103 105 104.0 0.600 0.600 0.183 0.187 EVO Head Quarters HQ-23 – 19 47 52 24 246 256 43 104 104 104.0 0.600 0.530 EVO Head Quarters HQ-24 Y 20 36 52 19 236 251 39 98 107 102.3 0.500 0.500 EVO Head Quarters HQ-25 – 18 38 42 14 236 236 32 100 104 102.0 0.550 0.550 EVO Head Quarters HQ-26 – 20 54 53 22 254 255 42 107 106 106.3 0.600 0.530 89 EVO Head Quarters HQ-27 – 26 60 70 24 266 274 50 107 113 110.0 0.650 0.575

Incoming search terms:

Yamaha V-Star 650 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Instruction sheet 54-600 1 Front head pipe 54-600-01F 1 Rear head pipe 54-600-01R 1 Front heat shield 54-600-02F 1 Rear heat shield 54-600-02R 1 Outlaw muffler 50-103-127 1 Muffler bracket 54-600-40 1 Head flange 54-110-41 7 2″ standard hose clamps 70-100-35 2 1 3/4″ HD Hose clamp 70-100-37 2 5/16″-18 carriage bolts 70-100-10 2 5/16″-18 flange nuts 70-100-15 1 8mm x 1.25 x 25mm flange bolt for front head flange 70-100-09 2 8mm x 1.25 x 20mm bolts /muffler bracket 70-100-05 2 10mm x 1.25 x 35mm bolts 70-100-85 2 Spacer .250 x .438 x .875 50-100-74 2 8mm x 1.25 Flange nut 70-100-22
Disassembly 1. Remove both Allen bolts that hold the muffler together (Fig. 1) . Also Loosen clamp from the front muffler to front head pipe (Fig. 2) , and remove allen bolts from rear head pipe and remove in one peace carefully (Fig. 3) . Figure 1 Figure 2 Figure 3 2. Once the two mufflers are removed with the rear head pipe, remove bracket by removing two 8mm bolts as shown and remove bracket. (Fig 4) Figure 4
3. Remove spring from brake light switch to the brake rod located on the right side footrest. (Fig 5) Figure 5 4. Remove two bolts holding the footrest, and brake pedal (Fig. 6) . Carefully rest right side footrest on the floor or you can use a two by four to rest the footrest onto. Figure 6

Incoming search terms:

HONDA VTX 1800 AIR HORNS AHVTX INSTALATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns. Cut a new piece of hose 2 ¾” long, replace the old short hose on the “Y” with this. Re-install the “Y” hose assembly onto the horns with the short hose on the long trumpet, route the hoses behind the horns and connect the long hose to the short horn (see photo 2A). 4. Remove the upper 8mm (12mm wrench size) motor mount bolt (see photo 2B). Install the horn assembly using the 8 x 55mm bolt and spacer tube provided. If the motorcycle is fitted with Honda line tubular radiator or engine guards the above mounting will not work. You will need instead to locate the “J” shaped bracket and small hose clamp provided in the hardware kit (see photo 2 on instructions of multi -application instruction sheet). Thread the hose clamp thru the bracket and attach to the frame or Honda line guards as shown ( see photos 2&3 ) tighten the hose clamp securely using a socket or wrench. Attach the horn set to the “J” bracket using the 5/16 x ¾” bolt, nut and lock washer provided. Position the horns so that they are angled down just slightly then tighten the bolt securely. Attach the remaining air hose to the “Y” connector, route the hose up over the top and to the rear of the engine. Cross the hose over to the right side of the rear cylinder head, then behind the electricals of the right side cover and coming out as shown ( see photo 3 A & B ). 5. Remove the center relay from its mounting bracket by lifting it upward and re-attach it lower and at an angle as shown (see photo 3C) using a small cable tie. Route two long cable ties thru the hole in the relay mounting bracket as shown (see photo 3D). Next cut a 16″ wire, strip both ends, crimp female spades to both ends. Attach this wire to the compressors pos (+) terminal. Cut an 8″ wire, strip both ends, crimp a female spade to one end and a fork terminal to the other. Attach this wire to the compressors neg. (-) terminal. Cable tie the compressor securely in place as shown (see photo 4). Route the hose to the compressor making sure there are no tight bends or kinks cut the hose to the desired length and attach it to the compressor. Route the neg. (-) wire with the fork terminal up and attach it to the 10 mm bolt as shown (see photo 4A) . Route the pos. (+) wire over to the relay on the left side of the motorcycle and attach it to terminal 30 or 87 on the relay (see wiring diagram)

Incoming search terms:

YAMAHA ROADSTAR 1600/1700 POWERSHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove both frame covers. Remove the left cover first to access a bolt that holds the right side cover in place. 2. Remove right side floorboard assembly held in place by two bolts (Figure 1). 3. Remove exhaust port Allen nuts. 4. Remove Allen bolts securing rear muffler to exhaust system mounting bracket. 5. Remove complete exhaust system. Begin by lifting muffler out of mounting bracket locating hole (assistance may be required). 6. Check condition of stock exhaust gaskets. Replace if damaged or worn 7. Remove two bolts attaching stock exhaust mounting bracket to frame. 8. Remove hose clamp securing rear brake hose to exhaust mounting bracket. 9. Remove brake hose banjo bolt from rear caliper. 10. Slide hose out of loop in bracket. 11. Check condition of sealing washers on banjo bolt and replace if damaged or worn. 12. Reconnect brake hose to caliper (without bracket) and torque Banjo bolt to 25 lbs. ft. 13. Brake system must be bled or brake will not operate correctly. Refill reservoir after bleeding 1. Remove exhaust system and heat shields from protective packaging. Place exhaust on a non-abrasive surface such as a blanket or carpet. Using a non-permanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 2). 2. Attach brake hose clamp to mounting bracket (stamped 362-P) using one 6x16mm flange bolt and nylock nut (supplied) to tab located on top of bracket (Figure 2). 3. Install mounting bracket using two 10x30mm Allen bolts and lock nuts (supplied)(Figure 3). 4. Carefully slide heat shields onto headers.

Incoming search terms:

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

Incoming search terms: