yamaha raider passenger foot peg bracket

You search Auto repair manual PDF yamaha raider passenger foot peg bracket, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha raider passenger foot peg bracket Direct Download speed 5282 Kb/s

  yamaha raider passenger foot peg bracket Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

V-Star 1100 Floorboard/ Foot peg Extension Kit Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Take notice of the position of the shift peg positions relative to the floorboard or foot-peg. You will be adjusting it back to these locations upon installation of the extended linkage. 2. Loosen the shifter rod jam nuts and remove the OEM shift linkage. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Remove the jam nuts from the OEM shift linkage and thread them gently on to the new shift linkage. 7. Install the new shift linkage by aligning the control swivel and the shifter swivel and turning the linkage. Be careful not to cross thread the linkage. The linkage will thread into both swivels simultaneously. Adjust to the desired position and tighten the jam nuts that you removed from the OEM linkage. Do not over-tighten or damage will occur to the threads. Right Side Installation: 1. Take notice of the Brake pedal position relative to the floorboard/foot-peg before removal, as it will need to be readjusted upon installation of the kit. 2. Remove the cotter pin from the brake linkage and remove the clevis pin. The brake linkage will now be separate from the brake pedal assembly. Do not discard anything. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Loosen the jam nut from the brake linkage and remove the linkage bracket. 7. Assemble the threaded brake linkage extension to the coupling nut and tighten using one of the provided jam nuts. Don’t forget the thread locking compound if your using it. 8. Thread the coupling onto the brake cylinder linkage and install the other end of the assembly into the brake pedal end. Tighten the jam nuts. You should be able to adjust the linkage for proper brake pedal location before tightening the jam nuts. 9. Readjust the brake light switch and your ready to roll

Incoming search terms:

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

2007 Yamaha V-Star 1300 Classic Straights Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install Nut strip into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install Nut strip into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks. NOTE: To achieve optimum performance from your Hard-Krome exhaust system we suggest installing the Dynojet jet kit for carbureted models

Incoming search terms:

1999-2007 Yamaha V Star 1100 3" Res-Tec Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Stock Exhaust System Removal 1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove O2 sensors from each muffler and cover with supplied cap plug. 3. Loosen clamps at mufflers. 4. Remove bolts that are holding mufflers at rear mounting bracket. 5. Remove mufflers. 6. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 7. Remove rear pipe assembly. 8. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 9. Remove front pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks

Incoming search terms:

Yamaha Stratoliner 2006 3" Big Straights REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 02-01-2012

download
1. Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding muffler at rear mounting bracket. 3. Remove Cables from exhaust valve. 4. Remove O2 Sensor from pipe. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 7. Remove complete pipe assembly. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system. 1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install O2 Sensor onto front pipe and install front pipe onto front cylinder, taking care to not scratch chrome surfaces on pipe, engine or motorcycle. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install 3/8-16 Square nut into each slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe onto rear cylinder. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — (Remove chrome plastic valve cover to access top nut) — DO NOT TIGHTEN NUTS! 8. Install 3/8-16 Square nut into each slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration.

Incoming search terms:

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

Incoming search terms:

YAMAHA XVS11A, XVS11AT, XVS11, XVS65A, XVS65AT, XVS65, and XV250 FACTORY MODIFICATION CAMPAIGN

0

Filed Under (Yamaha) by admin on 19-11-2010

download
INITIAL STEPS FOR ALL MODELS 1. Remove the passenger seat mounting bolt or nut, and then remove the passenger seat. 2. Unscrew the two mounting bolts for the passenger-seat bracket, and then remove the seat mounting bracket from the passenger seat. Save the two mounting bolts and washers for reuse. Hold the original bracket for 90 days with a Warranty Parts Tag. 3. Install the new seat bracket from the kit using the original bolts and washers. The new bracket has a larger hole for the grommet. PASSENGER SEAT BOLTS WITH WASHERS ORIGINAL SEAT MOUNTING BRACKET NEW SEAT BRACKET TORQUE: 8Nm (0.8kg-m, 5.8 ft-lb) ORIGINAL BOLTS WITH WASHERS
PAGE 4 of 15 4. Install the new grommet from the kit in the bracket hole. Continue to the appropriate instructions for the model being modified. XVS11A (V STAR 1100 CLASSIC), XVS11AT (V STAR 1100 SILVERADO), XVS65A (V STAR CLASSIC), and XVS65AT (V STAR SILVERADO) KIT PART NUMBER: 90891-20100-00 First complete the “Initial Steps For All Models” shown above to remove the passenger seat to install the new seat bracket and grommet. 1. Insert the new collar from the kit in the grom- met. 2. Hold the stud bolt from the kit at the unthreaded portion. Screw the cap nut onto the end of the stud with the longer threads until the exposed stud is 19mm long. • The cap nut is a self-locking type. The assembled stud length is important to allow the locking tab in the cap nut to be properly engaged. •Be sure the cap nut is installed on the end of the stud with the longer threaded por- tion. 3. Be sure the painted area around the stud hole is clean, then remove the backing and apply the new protective seal from the kit to the rea

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Incoming search terms: