yamaha v star 1100 clutch adj

You search Auto repair manual PDF yamaha v star 1100 clutch adj, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha v star 1100 clutch adj Direct Download speed 5282 Kb/s

  yamaha v star 1100 clutch adj Full Version speed 6162 Kb/s



HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

2008 Honda CBR1000RR Clutch Inner Installation PROCEDURE

0

Filed Under (Honda) by admin on 23-04-2011

download
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C  Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat

Incoming search terms:

Honda Shadow A.C.E. v. Yamaha V-Star 1100 Middleweight Import Cruiser Shootout

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
You want a big cruiser but you don’t need a large 1500 cc behemoth that weighs close to half-a-ton fully loaded. You want something you can cruise down the boulevard on but you want to be able to handle a corner or two. You want classic styling but you insist on reliability as well. If these are your guidelines, then Honda and Yamaha might have what you’re looking for in the guise of the Honda Shadow American Classic Edition and Yamaha V-Star 1100. Shadow ACE 1100 The ACE and V-Star have a few things in common: Both sport requisite V-twin powerplants (75° for the V-Star and 45° for the ACE) and both possess typical Japanese refinement. Aside from these similarities, the two rides are very different machines. While both machines are shaft driven, the ACE uses the shaft housing as the swingarm. Although this arrangement is effective, it’s a bit lacking style-wise. However, the whitewall tires and the classic fenders and tank help to create a traditional design that turns heads when you’re out and about. The V-Star uses a different approach, utilizing a pivoting sub-frame design with a hidden mono-shock that keeps the lines fluid and consistent with the rest of the bike. Although this beast isn’t equipped with whitewall tires, it still cuts a graceful, glittering profile. The only flaw we noticed was the small headlight that

Incoming search terms:

KAWASAKI CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the key from the ignition switch. Loosen the vent hose on the cover. Remove the clutch cover bolts (10mm socket) and take the clutch cover off. You will need to unplug the wires from the electric actuator and small sensor in the center of the clutch cover to totally remove the cover. To unplug the wires from the sensors, follow the wires to the connections under the plastic side panel and unplug at that location. 2. Remove the primary clutch bolt (19mm socket). This is a left threaded bolt. Insert clutch puller by hand (right hand threads) and tighten until clutch pops off the shaft. This tool is available from EPI, part number PCP-10. Loosen the secondary clutch nut (27mm socket) and remove both clutches at the same time. When you slide the secondary clutch of the machine there are four metal roller pins inside the center shaft of the secondary clutch. These will normally stay in place but if one does fall out refer to assembly instructions in step #6. 3. Disassemble the primary clutch by removing the eight bolts on the cover plate (10mm socket) and remove the spring. Remove one nut (10mm) on the bolt that holds the weight in place, slide the pin out of the clutch and remove the weight. Install EPI weight making sure the tip of the weight is resting on the inside ledge of the clutch. Slide bolt through the holes in the clutch and the weight and install the nut. Repeat this step for the other three weights. NOTE: If your kit has two different gram weights, for example two 54 and two 56 weights, be sure to place them directly across from each other (or every other one). This keeps the clutch in balance . 4. Install the EPI spring and bolt the clutch cover back on using a criss-cross pattern to tighten down the cover. There is a mark on the cover plate and the spider usually in the form of a dot or arrow in the casting. These are alignment marks and must line up when the clutch is assembled. 5. EPI recommends cleaning your clutches when you have them off your machine. Use a clean rag or towel with contact or brake cleaner that does not leave any oily film. Clean all parts of the clutch except for the clutch bushings. Solvent can damage your bushings; just use a dry rag to clean them

Yamaha XVS650 and 1100 Drag Star/V-Star Service and Repair Manual

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Fortunately, Haynes cruises to the rescue with the introduction of its new Service and Repair Manual for all Yamaha XVS650 and 1100 models – XVS650 (‘97-’05), XVS650A Classic (‘98-’05), XVS1100 (‘99–’05) and XVS1100A Classic (‘00–’05). Hailed as “… essential reading for any biker tackling his own servicing…” by Motor Cycle News, Haynes manuals have an enviable reputation. The new manual provides fully illustrated, step-by-step instructions for DIY servicing, overhaul and repairs of the engine and transmission, fuel and ignition systems, suspension and steering, the braking system and the electrical system. Each task is given a spanner rating for complexity and experience required. Checking and adjusting the valve clearances is rated as three spanners out of five. There are full-colour sections on the history of the models, on daily preride hecks and those all-important wiring diagrams, plus tools required and Haynes Hints. For instance, when changing the brake fluid how to tell when all the old fluid has been displaced The section guiding readers

Incoming search terms:

BMW Motorcycles R 850/ R 1100 Series and K 1200 RS – New Clutch and Pressure Plate

0

Filed Under (BMW) by admin on 16-11-2010

download
Details: All R 850/R 1100 and K 1200 RS models produced from December 1997 have received a new clutch disc, manufactured by VALEO, and a new pressure plate (see applicable part numbers below). Earlier production for both series can be fitted with the new parts. However, due to changes in specifications (a thicker pressure plate, a thinner clutch disc), the new VALEO clutch disc is not compatible with the old pressure plate. In this application, the new clutch disc and pressure plate must be replaced as a pair. Series Production: R 850/R1100 models: Starting with December 1997 production. K 1200 RS: Starting with December 1997 production. Part Number: R 850/R1100 Models: VALEO Clutch Disc: 21 21 2 325 864 Used only in conjunction with Pressure Plate: 21 21 2 325 863 R 850/R1100 models: VALEO Clutch Disc with reduced play on gearbox input shaft (KD – Scheibe): 21 21 2 325 862 Used only in conjunction with Pressure Plate: 21 21 2 325 863 K 1200 RS: VALEO Clutch Disc: 21 21 2 332 973 Used only in conjunction with Pressure Plate: 21 21 2 332 974 Attention: For R 850/R1100 and K 1200 RS models with production dates of 12/97 and later, all clutch parts can be replaced individually, as the new pressure plate will already be installed. On earlier production examples, installing the new VALEO clutch disc without replacing the pressure plate will not allow the clutch to completely disengage.

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

DUCATI EVOLUZIONE SLIPPER CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip

Incoming search terms: