yamaha virago 750 vacuum hoses

You search Auto repair manual PDF yamaha virago 750 vacuum hoses, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha virago 750 vacuum hoses Direct Download speed 5282 Kb/s

  yamaha virago 750 vacuum hoses Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

Aprilia Falco Synchronizing the Cylinder Vacuum

0

Filed Under (Aprilia) by admin on 26-10-2010

download
Motorcycle cylinders work quite independently compared to automobiles. Separate carburation, intake manifolds, exhaust pipes and sometimes even independent air filters allow the cylinders to be tuned so that one may be making more power than another. This can be due to differences in air flow, temperature, injection, or valve adjustment betwen the cylinders. Periodically, the cylinders should be synchronized. This is usually done by comparing intake manifold vacuum beneath each throttle and trimming the mixture until balanced. Some old-timers will tell you it can be done by ear, listening to the air flow in each carb throat through a tube stuck in your ear. Most modern tuners have switched to mercury sticks. Rigid tubes stuck in a bath of mercury are attached to the vacuum source. The vacuum draws the mercury up the sticks in proportion to pressure difference between the manifold and the atmosphere. In order to smooth out the individual vacuum pulses, a damping device is needed. This is nothing more than a small orifice (pin hole) restriction in the lines, placed close to the manifold with an air reservoir (length of tube) behind it. Because there is no real air flow in the gauges, there is no pressure drop across the orifice. But when the manifold vacuum drops there is a delay before the gauge pressure can bleed off and it appears steady and readable. Other types of vacuum gauges include mercury-less versions (that draw metal rods), or traditional needle, or “clock” gauges. The clock gauges are very fast acting (they are designed that way so you can see engine problems such as sticking valves). You will definitely need a damper if you choose a clock gauge. I would recommend using two side by side gauges for checking cylinder synch. The reason is, the cylinders are not perfectly independent. As one cylinder drops strength, the idle drops, and this will change the vacuum in the second cylinder’s manifold. It takes a bit of fooling around to get a cause-and-effect feel when you are turning the screws. Swapping gauges would make this difficult

YAMAHA CRANKSHAFT LOWER END REMOVAL AND INSTALLATION TOOLS

0

Filed Under (Yamaha) by admin on 08-01-2012

download
90 LOWER END REMOVAL & INSTALLATION TOOLS SHOP EQUIPMENT & TOOLS 35-8399 35-8513 35-8516 35-8508 35-8504 35-8507 YAMAHA CRANKSHAFT PROTECTORS Sold each. 35-8504 YM-4063-A, XV750/920 Virago, XT550, YFP350, YFM660R Raptor 35-8399 YM-1382, XT250/XT350, RZ350, YFP350, YFZ350 35-8507 YM-33282, XV500 Virago, XZ550 Vision, XVZ12/13 Venture & Venture Royale, VMX12 V-Max 35-8508 YM-38145, XV750/XV1000 Virago YAMAHA CRANKSHAFT INSTALLATION SET Sold as a set. Consists of the following: Qt1-Installing Pot, Qt1-Pot Spacer, Qt1-Bolt. 35-8509 YU-90050 Crankshaft Installation Set OPTIONAL POT SPACERS 35-8513 YU-90070-A, XV750/920 Virago, XT550, TT600 35-8515 YU-91044, YFM350, SRX600, XT550/600 35-8516 YU-1202, SR500, TT/XT500 CRANKCASE PRESSURE TESTER An accurate method for checking possible air leaks on two-stroke engines. Complete with air pressure gauge, pump-up bulb and all fittings and adapters for single and multi-cylinder two-cycle engines. 35-5962 Crankcase Pressure Tester CRANKSHAFT INSTALLING JIG TOOL Supports and centers crankshaft webs while assembling two-stroke engine cases and rebuilding crankshafts. Prevents rod misalignment. Adjustable tang ends. 35-9804 Crankshaft Installing Jig Tool CRANKCASE SEPARATOR TOOL This tool will work on most two and four stroke engines that have a vertically split crankcase. Moveable fingers allow a multitude of bolt patterns to be used so it will work on a variety of models. Includes 6mm and 8mm mounting bolts, center pulling bolt and a three leg frame that is appropriate for many applications. 35-9642 Crankcase Separator Tool 35-9637 Replacement 6mm and 8mm mounting bolts. Each

Incoming search terms:

HARLEY DAVIDSON BRAIDED OIL HOSES INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery negative cable. 2. Drain engine oil according to Service Manual instructions. 3. Removing the rear exhaust pipe may aid in giving access to the oil lines and fittings. If necessary, remove the rear exhaust pipe according to Service Manual instructions. 4. See Figure 5 and Figure 1 for description and location of the three oil hoses that are replaced with the braided hoses in this kit. Remove the original equipment oil feed, return and vent lines. 5. See Figure 2. Remove and discard the original hex threaded quick disconnect fittings (1), (2) and (3) at the engine for each of the hoses removed in Step 4. To remove the fittings, turn the hex in a counterclockwise direction until free. 6. See Figure 5. Install the threaded adapter from the kit onto the corresponding oil line. The adapters for the return and vent lines are the same size. The adapter for the feed line is larger in size. Coat the male threads of the adapters with Loctite 565 thread sealant. NOTE Be sure to install hoses on the correct fittings. If you mix up the hoses, you will change the direction of the engine oil flow, causing severe engine damage. 2 3 1 is04165 1. Oil Return Hose 2. Oil Feed Hose 3. Oil Vent Hose Figure 1. Installed Oil Hoses

Yamaha TDM900 Installing and removal the Vacuum Actuator

0

Filed Under (Yamaha) by admin on 28-12-2011

download
Attach the cable adjuster to the bracket. Position the adjuster so that it is screwed all the way in. Do not tighten the lock nuts on the adjuster yet. • Route the new ‘carburettor’ cable around and out the RHS of the bike under the frame rail as shown in the following photos. Installing the Vacuum Actuator • Mount the actuator on the RHS fairing support using the bracket provided and two bolts, nuts and flat washers. The mounting bracket fits on the inside face of the fairing bracket. The small plate fits on the outside and clamps the actuator to the faring frame.

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

BMW K1100LT Installing Real Cruise Control

0

Filed Under (BMW) by admin on 26-10-2010

download
The vacuum reserve canister (VRC) is used to provide adequate vacuum for the cruise control servo unit. It uses the throttle body as a vacuum source and, via the vacuum check valve, stores up vacuum for the servo to use to pull the throttle cable. You can also buy one of these at an auto parts store for about $10-15 but I decided to build my own so I could make one that would fit inside the left front of the main fairing body. If you decide to buy one, make sure you can return it if it doesn’t fit inside the fairing or be prepared to mount it somewhere else like inside the tail cowl. I used 8″ of 2″ diameter PVC tubing because that is the length that would easily fit inside the fairing It is mounted inside the fairing in front of the left “bucket.” I used white PVC tubing but, in hindsight, would use black if possible since it is visible to the rider when mounted in the fairing. I suspect that the cruise control may actually work without the use of the vacuum canister so you might want to try the cruise without a VRC. If you do install the cruise control without a VRC, you’ll want to put a vacuum check valve in the vacuum hose that goes from the throttle body to the cruise control servo unit.
11/30/2005 08:23 PM Installing Real Cruise Control on a BMW K1100 Page 4 of 8 used epoxy for assembling the VRC as it’s my permanent adhesive of choice. Cut an 8″ length of 2″ diameter PVC tubing. Sand the edges. Drill two holes as shown for the check valve and vacuum tee. There’s a vacuum tee in the bags of installation miscellany that come with the cruise control. File the webbing from the right angles before gluing it and the check valve in place. Remember to glue the tee into place before gluing the end caps on. Make sure everything has an airtight seal. I used zip-ties to hold it in place inside the main fairing body in front of the left bucket

Incoming search terms: