yamaha vmax 1200 pilot jets

You search Auto repair manual PDF yamaha vmax 1200 pilot jets, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha vmax 1200 pilot jets Direct Download speed 5282 Kb/s

  yamaha vmax 1200 pilot jets Full Version speed 6162 Kb/s



Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Incoming search terms:

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Honda CARBURETOR ADJUSTMENT TOOLS

0

Filed Under (Honda) by admin on 17-12-2011

download
K&L CARBURETOR ADJUSTMENT WRENCHES These tools use tough and accurate bevel gear actuation instead of cable for professional use. The aluminum handle includes index marks for accurate tuning. Sold each. Three types available: 35-9653 Slot-type Pilot Screw Adjustment Wrench for Kawasaki/Suzuki/Yamaha 35-9658 Slot-type Pilot Screw Adjustment Wrench with longer tip for Kawasaki/Suzuki/Yamaha 35-9650 D-type Keihin Pilot Screw Adjustment Wrench for Honda 90-DEGREE 1/4″ HEX DRIVER This gear driven, 1/4″ hex driver set is made of high-grade aluminum and stainless steel. Strongest tool of it’s type on the market. Designed for use on hard-to-reach pilot air screws on inline fours. Can be used with any 1/4″ or 6mm hex bits. 35-7820 90-Degree 1/4″ Hex Driver Set: Includes straight slot, phillips, d-shape pilot screw bit, 6mm hex jet bit & 1/4″ – hex – 1/4″ drive bit. FCR CARB TOOL Set includes three bits – 6mm hex for main jets, long reach straight slot for pilot jets and 3mm allen for float bowl removal. Longer bits make this set ideal for reaching into recessed cavities when adjusting Keihin FCR carburetors. Sold as a set. 35-7978 FCR Carb Tool 12″ DRILL BIT For removal of carburetor plug. (mixture screw plug) 1/8″ bit x 12 inch length. 35-1186 YM-33217-16 JET DRIVER 35-2270 Perfect for removal of jets from small recessed passages

Incoming search terms:

Hot-Start Kit For Yamaha YZ/ WR 400F

0

Filed Under (Yamaha) by admin on 16-12-2010

download
Blaster Rear Brake Kits 121-01298 • YFS200 Blaster ’88-’98 • This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper. 121-01299 • Same as 121-01298 +4″ • Cable is 4″ longer for extended swingarms. 121-01027 Replacement Ratchet Spark Plug Wrench 121-08147 • Designed specifically to fit where there is limited space • Ratchet mechanism works one way • Fits standard 13/16″ plugs
INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS R . 03-15-06 21 (626) 792-7384 www.FlandersCompany.com Fax: (626) 792-5341 www.FlandersCo.com Specialty Tools Swingarm Bearing Tool 121-080213 • Designed for installation of the swing arm bearings on late model Japanese motorcycles • Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm without beating on it with a hammer Main Jet Wrenches • High-quality die cast construction • 6mm round and hex jets and 8mm round • Cap holds a few spare main jets • Sold each 121-08023 6mm Hex (Fits 6mm hex main jets) 121-08024 8mm Round (Fits 8mm round main jets) 121-08025 6mm Round (Fits 6mm round main and pilot) Allen Extension 121-080184 • 5mm allen on a 6.25″ long, 3⁄8-drive extension for hard-to-reach case bolts • Designed for use with air tools • Great for splitting engine cases

DUCATI CLUTCH INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
When a vehicle is so equipped, the pilot must be replaced. The pilot is located in either the engine’s crankshaft or in the center of the flywheel. To remove a flywheel-fit pilot, remove the flywheel from the engine and drive or press out the pilot from the backside of the flywheel. Press or gently tap new pilot into flywheel after flywheel has been machined (where applicable). For crankshaft-fit pilots, an effective means for removal is to select a drift punch or wooden dowel that fits snugly into the old pilot. Then, pack the old pilot tightly with grease. Using the drift punch (or dowel) and a hammer, drive the grease toward the engine. The grease will not compress and will in turn push the old pilot out of the crankshaft. Install the new pilot carefully using a bearing driver. NOTE: Do not grease new pilots. New pilot bearings come pre-greased (often with special synthetic grease). Bronze pilot bushings have oil in the pores of the material that grease will clog. For bushings, a few drops of 30W oil can be used if desired. PRESSURE PLATE AND DISC Install flywheel (refer to flywheel section above) . Always tighten flywheel to crankshaft bolts in a star pattern to manufacturer’s torque specification. Before installing the disc, make sure that it slides smoothly on the transmission input shaft. Apply a thin coat of high temperature grease (such as wheel bearing grease) to the splines of the input shaft. DO NOT USE ANTI-SEIZE! It does not cling to rotating parts. Slide the disc back and forth on the input shaft and remove any extra grease that squishes out of the splines of the disc. Do not get grease or oil on the disc facing. Any grease or oil on a disc facing can be removed with alcohol or brake cleaner if done quickly. Lay the disc on the flywheel noting the flywheel side of the disc and hold it in place with the alignment tool. Clean the pressure ring of the pressure plate with brake cleaner to remove the rust inhibiting coating. Do not spray the entire pressure plate with brake cleaner as lube for internal parts will be removed. Set the pressure plate on the flywheel dowel pins (if equipped) and hand tighten the hold-down bolts. With hand tools, tighten pressure plate bolts ½ turn at a time in a star pattern until the manufacturer’s torque specification is met. Remove the alignment tool. NOTE: Different brands of the same pressure plate may have a difference in appearance and uninstalled lever height. These are not issues. Appearance can vary greatly and the installed lever height will be the same.

Incoming search terms:

YAMAHA MOTOR CORPORATION, U.S.A. STREET & ENDURO MOTORCYCLE LIMITED WARRANTY

0

Filed Under (Yamaha) by admin on 27-12-2011

download
GENERALEXCLUSIONS from this warranty shall include any failures caused by: a. Competition or racing use. b. Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts. c. Abnormal strain, neglect, or abuse. d. Lack of proper maintenance. e. Accident or collision damage. f. Modification to original parts. g. Damage due to improper transportation. SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance. THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to: 1. Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual. 2. Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory. WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. Areasonable dealer imposed fee may be charged for the inspection. In no case will warranty be extended beyond the original period. EMISSIONS CONTROLSYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

Incoming search terms:

2007 Yamaha VMAX/ VMX12W1(C) OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
GASOLINE IS HIGHLY FLAMMA- BLE: * Always turn the engine off when refueling. * Take care not to spill any gasoline on the engine or exhaust system when refueling. * Never refuel while smoking or in the vicinity of an open flame. * Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. * Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: * The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. * Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. * Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. * When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the carburetor or fuel tank. * If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

MC 1200 Motorcycle Trailer – 1200 lbs Assembly Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Tongue: Remove tongue assembly from the frame bundle. Insert into the tongue channel and slide into the front cross member of the frame. Secure with two (2) 3/8″ X 4″ carriage bolts and 3/8″ flange lock nuts. Tighten. Thread the tongue wire harness through the front top hole in the tongue and pull out the hole provided in the left side of the tongue towards the rear. Connect to the frame harness with the plugs provided. Install grommets. Safety Chains: Insert a 3/8″ X 1-1/4″ hex bolt into a 3/8″ flat washer, safety chain and then through the lower hole on the front of the tongue. Place on a 3/8″ flat washer on the inside of the tongue and secure with 3/8″ flange lock nuts. Repeat procedure on the opposite side of the tongue. Tighten. Coupler: Mount the coupler onto the tongue with a 1/2″ X 4″ hex bolt trough the rear mounting holes of the coupler. Using two (2) 1/2″ X 1″ hex bolt attach the coupler to the tongue using the front mounting holes. Secure with flange lock nuts. Tighten. Axle: Attach the spring busing in the rear spring shackles with 1/2″ X 3- 1/4″ hex bolts and 1/2″ flange lock nuts. Position the axle under the trailer with spring eye to the front of the trailer. Slip the flat end of the spring in the rear spring shackle above the bushing just installed. Secure the front spring eye to the front spring shackle with 98/16″ X 3-1/4″ hex bolts and 9/16″ hex lock nuts. Tighten. Mount the tire and rim assemblies to the axle assembly with 1/2″ lug nuts and tighten to 80-90 ft./lbs. of torque using the rotation pattern as shown in the Shore Land’r Owners Manual . Retorque the lug nuts after 50 miles of driving and then periodically thereafter. Ramps: Locate the loading ramp. Note that one end has two holes punched in the bottom of the channel. (See parts drawing) Insert a 3/8″ X 1-1/2″ full threaded carriage bolt into one of these holes. Secure in this position using a 3/8″ flange lock nut. Tighten Place a second 3/8″ flange lock nut onto the same bolt only until the threads of the bolt are exposed through the nut locking it in

Incoming search terms:

YAMAHA V-STAR 1100 HYPERCHARGER AIRCLEANER INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
STEP 1 Remove the driver and passenger seats from the bike. Remove the negative battery cable from the battery and tuck it out of the way to reduce the possibility of sparks. STEP 2 Remove the two rear tank mounting bolts. Remove the plastic tank mounting snap stud. (Push in on the center of it to release). Slide the tank back to expose the top of the engine. Make sure the tank is solidly in place so it does not fall! You may remove the tank completely from the bike if you’re not certain the tank will stay in place while you are performing this installation. STEP 3 Remove the stock air cleaner cover, element, and backing plate. Twarrants that any Küryakyn product sold hereunder, if properly installed, maintained and operated under normal conditions, shall be free from any defects in materials and workmanship for a period of one (1) year from the date the Küryakyn products are sold to the customer. CONSEQUENTIAL DAMAGES: Küryakyn shall not be liable for any consequential or incidental damages. ABOUTOURCA TA LOG You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual catalogs. Order online today-select the “CATALOGS” icon. Each Küryakyn™ product comes with a Proof-of-Purchase good for a complimentary catalog. Details in packaging. Be sure to ask your local dealer about other Küryakynproducts, the motorcycle parts and accessories designed for riders by riders. ©2003 Küryakyn USA™All Rights reserved. STEP 4 See PIC. 1and PIC.2. Remove the grommet from the bracket. STEP 5 Placing your long handled Phillips screwdriver as shown in PIC.3, loosen the clamp on the air duct and remove the duct. Remove the clamp from the duct— it will be reused. Now is a good time to proceed with rejetting of the carburetors. Consult your factory service manual for this procedure. We have supplied jets to cover most common applications. Jetting Recommendations: See FIG. 1for jet locations. With stock exhaust or Cobra Slip-On Mufflers • 1.2 Pilot Air Bleeds in both carbs • One .020 shim added to raise each needle • 122.5 Main Jet in the front cylinder’s carb • 120 Main Jet in the rear cylinder’s carb • Pilot Mixture Screw (PMS) 2 turns out from lightly bottomed With Vance & Hines, Samson, or open “Drag” pipes • 1.2 Pilot Air Bleeds in both carbs • One .020 shim added to raise each needle • 125 Main Jet in the front cylinder’s carb • 122.5 Main Jet in the rear cylinder’s carb • Pilot Mixture Screw (PMS) 2 turns out from lightly bottomed NOTES 1. The factory installed plug covering the PMS will have to be removed in order to access the screw. 2. Because the float bowl screws are easily damage during removal, we have included 8 replacement float bowl screws with socket heads, just in case they are needed. BE SURE TO VENT THE FLOAT BOWLS TO THE BACK OF THE HYPERCHARGER — THIS IS NECESSARY FOR BEST DRIVABILITY AND MAXIMUM PERFORMANCE!!!! (See Step 12.) STEP 6 See PIC.4. Insert both flanges of the rubber air duct through the opening in the mounting bracket. Place the Stock duct clamp on the new intake duct — the clamp screw should face forward.

Incoming search terms:

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Incoming search terms: