yamaha royal star venture trailer hitch

You search Auto repair manual PDF yamaha royal star venture trailer hitch, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yamaha royal star venture trailer hitch Direct Download speed 5282 Kb/s

  yamaha royal star venture trailer hitch Full Version speed 6162 Kb/s



Yamaha Venture Royal Star Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1) Secure motorcycle in an upright position. 2) Remove saddle bags 3) For hitch clearance you will need to install the enclosed muffler lowering spacers. 4) Attach forward brackets A (left) and B (right) to motorcycle rear crash bar with U-Bolts. Also attach brackets at the point where the saddle bag sub frame and rear crash bar connect using new bolt provided. 5) Attach rear brackets C (left) and D (right) to motorcycle rear frame using new bolts provided. See diagrams next page. Attach top portion first then bottom portion. 6) Attach brackets A and B to forward arms of receiver hitch. Brackets mount on BOTTOM of hitch arms. 7) Attach bottom of brackets C and D to rear of hitch. 8) Now tighten all bolts working from rear forward. 9) Replace saddle bags and double check all bolts for tightness. Hitch Diagrams InstaTrike Installation 1. Place your motorcycle on a smooth level surface and attach leveling jack stands. 2. Push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 3. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 4. Align InstaTrike wheels. (initial installation only. Check periodically and realign if necessary) 5. Bolt leanstop braces to hitch. Be certain to replace washers/spacers in the same configuration as when you removed them. 6. Remove leveling jack stands. 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

YAMAHA ROYAL STAR VENTURE CENTERSTAND REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Stand Installation. Locate the four mounting holes on the frame that correspond with the holes in the centerstand. Slide the front of the centerstand up into the frame and align the large bolt holes with those in the frame. Install the (2) 7/16″ x 1″ bolts with washers thru the frame and centerstand. Install the (2) 7/16″ nuts and make finger tight. (on California models the fuel tank vent canister must be removed and the hoses bypassed see note below) Pivot the rear of the centerstand up to align the (2) smaller holes in the stand with those in the frame. Insert a phillips screwdriver into one of the (2) remaining mounting holes and pry the other hole into alignment. Install one of the ¼” x ¾” bolt with a washer from the top down thru the frame and centerstand. Install the lock nut finger tight. Remove the screwdriver and install the remaining ¼”x¾” bolt washer and nut. Tighten the ¼ ” bolts securely 10-12 ft. lbs., then tighten the 7/16″ bolts securely 20-24 ft. lbs. 2. Stop Bumper Installation. Next install the centerstand-stop bumper and bracket onto the frame. Locate the bolt “A” in photo #1. Notice there is another 10 mm bolt just below it. Remove the lower bolt. Attach the bumper bracket to this hole using the longer bolt and washer supplied. The leg of the bracket with the bumper should face inward towards the center of the motorcycle. Adjust the height of the bracket to keep the pedal arm 3/8″ to ½” from the bottom of the exhaust pipe. Tighten securely. 3. Emissions Valve Relocation. You will notice that the right leg of the stand near the foot comes in contact with the emissions valve. The valve needs to be moved outward or to the right as you are sitting on the motorcycle approximately ¾”. This is done as follows: Remove the (2) 10 mm bolts holding the emission valve and bracket to the frame. See photo #2. With the hoses still attached pull the valve down to gain access to the (3) allen screws. Remove the (3) allen screws and (2) nuts holding the bracket to the valve, turn the bracket over and re-assemble the valve onto the bracket as shown in photo #3. Re-install the valve onto the frame. You may need to rotate the hose clamp clips out of the way and/or bend the entire valve bracket assembly outward slightly to gain clearance between the centerstand leg and foot. 4. Using Your New Centerstand. To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now, put all of your weight on to the centerstand pedal (stand on it). Pull up and back on the grab rail using a rocking motion to rock the motorcycle up on to the stand. Remember it is a matter of using your body weight and leverage not lifting! 5. Getting the Bike Down off the Centerstand. Holding the left handle bar and saddlebag guardrail, firmly rock the motorcycle off the centerstand. You can also rock it off while sitting on the motorcycle.

Incoming search terms:

YAMAHA XVZ 1300 Royal Star/ Venture SPEEDOMETER COWL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 07-11-2010

download
Speedometer Cowling Chrome 1 2 Alcohol Wipe 1 NOTE: Allow time for the 3M® brand quality tape to cure for 24 hours at 19-32° C before washing or waxing the motorcycle. INSTALLATION 1. Position the Speedometer Cowl in front of the Speedometer. The Cowl attaches to the Speedometer Cover, not on the rubber ring around the Speedometer. The Cowl should be symmetrically located in relation to the Speedometer, use the Speedometer markings as a reference. 2. Remove the red backing tape from the adhesive strip on the base of the Speedometer Cowl. 3. Position the Speedometer Cowl as done in step 1. Make any position adjustments now. 4. Firmly press the Speedometer Cowl in place on the Speedometer Cover. 5. Allow twenty-four hours for the adhesive to fully set before washing or waxing.

Incoming search terms:

Yamaha V-Star 1300 Receiver Hitch Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Install all bolts loosely until all brackets are in place Remove accessories (saddle bags, back rests, etc) before hitch installation. 1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time
4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle.

HARLEY DAVIDSON FLH AND FLT TRAILER HITCH OR RACK LIGHTING WIRE HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Remove the seat and locate the tail light plug, this should be attached to the frame with a plastic clip where the fender meets the frame cross member. Unplug the connector and plug in the male and female ends of the supplied wire harness. Route the harness as shown following the other wire looms and then down along the main frame of the trailer hitch or your fender support to the bottom of the rear fender. Secure the harness using the supplied cable ties. Install a plug that matches that of your trailer. The wires in the harness functions/colors are as follows: Black = Ground Brown = Tail Light Red = Brake Light Orange = Left Turn signal Blue = Right Turn signal NOTE: If your trailer has only four (4) wires you will need to use a 5 to 4 wire converter. These are available at most auto parts stores or thru RIVCO Products. NOTE: If your trailer uses more than two (2) incandescent tail light bulbs the use of a trailer wiring isolator is strongly advised as this additional load is too much for the motorcycles wiring to support and may cause damage to the electrical system. Trailer wiring isolators are available although not as common in auto parts stores and are also available thru RIVCO Products. If you are installing both you must first install the 5 to 4 wire converter then the isolator then to the trailer plug.

Incoming search terms:

1100cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Receiver Hitch Installation Install all bolts loosely until all brackets are in place 1) Place motorcycle on center stand and be certain it is level. 2) Remove saddlebags if necessary for easier installation. 3) Mount bracket A to the lower front crash bar bolt Left side (new bolts provided) and top of left hitch arm. 4) Mount bracket B to the lower front crash bar bolt Right side (new bolts provided) and top of right hitch arm. 5) Bracket C mounts to rear of hitch and sub frame bolt located behind tail light (new bolt provided) This bracket mounts inside the rear fender. 6) Attach brackets D and E to rear of hitch. 7) Bracket F attaches to bottom of bracket D and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 8) Bracket G attaches to bottom of bracket E and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 9) Brackets D and E (with brackets F and G) attach to bottom rear saddlebag sub frame with U-bolts. 10) Tighten all bolts. INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Push the motorcycle off of the center stand and risers if used. 6. Bolt leanstop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them. see diagram next page 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

2005-2009 ROYAL STAR TOUR DELUXE & 1999-2010 VENTURE OVAL BAG SLASH SLIP-ON MUFFLER SET INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
1. Loosen the bolt on the front clamp securing the muffler to the headpipe. Important: Do not unbolt the OEM headpipes. 2. Loosen and remove the bolt from the muffler hanger located beneath the saddlebag. 3. Pull the muffler off the headpipe. It may be necessary to rotate the muffler and wiggle it a bit to free it. 4. Place a new exhaust clamp on the front of your new Oval Slash pipe. 5. Slide the new exhaust over the headpipe by rotating it and pushing it forward at the same time. 6. Align the hole in the mounting bracket and reinsert the OEM rear mounting bolt with the supplied nut and lock washer. Finger tighten only at this point of the installation. 7. After the brackets are in place, securely tighten all exhaust pipe clamps and brackets. 8. Reinstall the saddlebag. 9. Repeat Step #1 through Step #9 for the other side of the motorcycle. 10. For optimum performance we recommend the carburetors air/fuel mixtures be adjusted for the change in exhaust flow and back pressure. For best results, this procedure should be performed by a qualified Yamaha service technician. 11. Tighten all bolts/nuts after riding 100 miles, including baffle retaining screws

Incoming search terms:

Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

Incoming search terms: