yerf dog 3203 seat belt harnesses

You search Auto repair manual PDF yerf dog 3203 seat belt harnesses, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yerf dog 3203 seat belt harnesses Direct Download speed 5282 Kb/s

  yerf dog 3203 seat belt harnesses Full Version speed 6162 Kb/s



HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

1999 TOYOTA SEAT BELT EXTENDERS REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 11-10-2011

download
increase the length of their seat belts may obtain Seat Belt Extenders at no cost through their local Toyota dealer. The extender is available in 6 inch, 9 inch, 12 inch, 15 inch and 18 inch lengths. The extender is available only in black . Owners are informed of the seat belt extender availability through the Toyota Owner’s Manual included in each vehicle. The customer (individual requiring the extender) must visit a Toyota dealership to have the required measurements made and to complete the seat belt extender worksheet. The worksheet will allow the proper fitting and selection of a seat belt extender for the customer. The dealership personnel should then determine the applicable part number and place a Critical Order through the TDN Parts Network. The dealership service department should complete the affixed Seat Belt Extender Label and review the “owner instruction sheet” with the customer. The dealership should give a copy of the completed worksheet to the customer and keep the original in the customer’s file. To assure utmost owner satisfaction, it is recommended that a dealership designate one person to coordinate all activities related to the seat belt extender issue. From past sales history, it is recommended that dealerships do not stock Seat belt extenders due to low demand and the need for customer fitting

HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

HARLEY DAVIDSON BADLANDER SEAT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat strap from motorcycle. Retain all hardware. Discard seat strap. 2. Remove existing seat from motorcycle by removing Phillips head screw with lockwasher, and nylon washer from rear fender mounting bracket. Retain all hardware except discard nylon washer. 3. Disengage seat from frame tab at front of seat. 4. Install new seat onto motorcycle, making sure bracket on front of seat fully engages into seat mounting tab on frame. NOTE On rear fenders of 1997-1999 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997-1999 models. 5. On pre- 1997 models , secure seat onto rear fender with original screw and lockwasher and place guide washer (1) between seat bracket and rear fender. 5a. On 1997-1999 models , secure seat onto rear fender with original screw and lockwasher. After installing seat, pull upward on front of seat to be sure it is locked in position. If seat is loose, it could shift during vehicle operation, resulting in loss of control of vehicle and death or serious injury. 6. Use original hardware to install new seat strap (2) in same location as old seat strap. On FXSTC, Softail Custom models, fasten seat strap to fender support

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Related Item : what is the screw size for the harley grab strap hole (2)softail deluxe seat nut (1)seat fitting harley (1)proper castle nut and cotter pin installation (1)plug holoes in rear fender left by solo seat (1)motorcycle sidestand strap (1)major ground strap for 1990 harley flt location (1)how to install harley seat fender nut (1)filling seat bolt hole on harley (1)cafe seat pan for a sporster 48 (1)