yutube 1999 valkyre kick stand assembly

You search Auto repair manual PDF yutube 1999 valkyre kick stand assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  yutube 1999 valkyre kick stand assembly Direct Download speed 5282 Kb/s

  yutube 1999 valkyre kick stand assembly Full Version speed 6162 Kb/s



HARLEY DAVIDSON CHROME DISPLAY STAND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and disconnect the battery negative (-) cable or remove the main fuse. NOTE Make sure that the cutout (B) of the strap (3) is oriented to the rear of the motorcycle after installation. 2. See Figure 2. Install strap (3) and weld nut (4) to the frame in the locations shown. 3. Position the center display stand over the mounting holes under the frame, oriented so that the skid plate faces for- ward. 4. Apply a small amount of Loctite 271 – Red to the two long screws (1) and secure the rear of the display stand to the frame by installing the two screw to the strap. 5. Apply a small amount of Loctite 271 – Red to the short screw (2) and secure the front of the display stand to the frame by installing the screw to the weld nut. 6. Tighten screws to 60-96 in-lbs (7-11 Nm) . 7. Refer to the service manual and connect the battery cables or install the main fuse. 1 2 is05370 1. Flange side 2. Flat side Figure 1. Chrome Display Stand Foot Orientation ADJUSTING THE DISPLAY STAND The left and right feet of the display stand are independently adjustable to vertically level the vehicle with the display stand extended. To adjust the display stand: NOTE The display stand can be adjusted with rear tire to ground contact or with rear tire off the ground. With the rear tire to ground contact adjustment, the rear wheel is on the ground but enough weight is on the display stand legs to make the motorcycle stable from side-to-side and front-to-back. Using the display stand to center the motorcycle will require effort. With the rear tire off the ground adjustment, the rear tire clears the ground so tire can be rotated for cleaning or maintenance purposes. Using the display stand to lift rear tire off the ground will require more effort. Do not center the vehicle with someone on the vehicle. To reduce effort, remove stored items from saddlebags, if equipped

Incoming search terms:

Harley-Davidson touring bikes WHEELDOCK EZ-UP Center Stand Installation Instructions

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common problems: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter.

Incoming search terms:

Harley-Davidson The WHEELDOCK EZ-UP Center Stand Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2012

download
Unlike other center stands, the WHEELDOCK EZ UP stand requires very little effort to operate and can usually be done while still on the bike by simply pushing down on the foot lever with your left foot. Once you feel both feet of the center stand in contact with the ground, transfer your weight up off of the seat and onto the foot lever of the center stand. The stand should rotate under the bike and a bit forward lifting the bike quite easily. CAUTION: Never attempt to raise the bike with a passenger on board, as you will damage the foot lever. You can also raise the bike on the center stand by using the following traditional method: Place the bike on the side stand and step off to the side. From the left side of the bike, push the bike up to the vertical position and press down on the foot lever until both feet of the stand are in contact with the ground. Now apply weight to the foot lever while lifting up on the bike. For cleaning the rear wheel: first place a ½-inch piece of plywood under the stand and use this (beside the bike) method for placing the bike up on the plywood spacer; this will allow the wheel to rotate freely for cleaning. Do not try this while on the bike, as it will require too much foot pressure on the lever. You now have two options to get the bike off of the stand: You can simply rock the bike forward, or put the bike in gear and drive off in most cases as long as you are parked on a flat, level surface. Tips for solving common questions: If you have the correct height stand and you still have difficulty getting the bike up on the stand check the following: the bike must be in neutral, the wheel should be straight forward and not cocked, do not hold the front brake lever and make sure you have 15 lb or more air pressure in the rear suspension. These are the most common problems we encounter

Incoming search terms:

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms:

HONDA 1100 ACE, AERO AND SABRE CENTERSTAND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
Relocation of Regulator. Laying under the right side of the motorcycle, locate the voltage regulator. (finned aluminum box-approximately 3″x 4″) Note: See photo #1 – regulator already relocated. Remove the (2) 10 mm bolts attaching the regulator to the frame. Attach the bracket supplied to the regulator as shown. Using the original bolts, attach the regulator and bracket assembly to the frame as shown in photo #1 using the two 10 mm bolts supplied. Clamping Centerstand to Frame . Notice the centerstand is shipped with (2) white plastic washers. Note: See photo #2-A These are in place to overcome the spring tension or lock the stand in place and allow you to pivot the lower stand down partially to make installation easier. Pivot the upper stand about half way from the retracted to the extended (down) position. Note: This will require some force. If the stand will not stay in the position you can further tighten the two 9/16″ pivot nuts. Remove the bolts from the four band clamps. Wrap the (2) small clamps around the small upper frame tube and start the bolts so that the bolt will be at the bottom of the tube and the wrench head facing towards the rear of the motorcycle. Note: See photo #2. Center the stand on the frame from side to side so as to gain even clearance between the feet on the centerstand and the rear tire when the stand is in the retracted position. Holding the larger cradle up against the frame, tighten the (2) small clamps enough to hold the centerstand in place. Install one of the large clamps as shown in photo #3-A. Install the 2nd large clamp as shown in photo #2-C. Again retract the stand and check that the feet have even amounts of space from the side of the rear tire. Tighten the flour clamps securely 5-7 ft. lbs. Next remove the (2) 9/16″ pivot nuts and the white plastic washers as shown in photo #2-A. Re-install and tighten the 9/16″ pivot nuts securely 8-12 ft lbs. With the stand in the retracted position-adjust the stop bolt and lock nut, see photo #3-B, so that the stand is parallel with the ground and does not come in contact with any parts of the motorcycle. Using your new centerstand . To put the motorcycle up onto the centerstand, hold the left handle bar and saddlebag guard rail or grab under the bottom of the seat. Using the ball of your right foot, lower the stand to the ground. Rock the motorcycle from side to side slightly until you feel both feet of the stand touching the ground. Now put all of your weight onto the centerstand pedal (stand on it). Pull up and back on the grab rail or seat using a rocking motion to rock the motorcycle up onto the stand. Remember it is a matter of using your body weight and leverage not lifting!

Incoming search terms:

HARLEY DAVIDSON AUXILIARY BRAKE/RUN/TURN SIGNAL CONVERTER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative side first. 2. Remove the seat according to the procedures in the applicable Service Manual. NOTE Federal regulations require that red turn signal lenses need to be a minimum of 4 inches from the tail or stop lamp, edge to edge. In order to ensure this spacing requirement, new directional stand-offs are provided in kit and must be used to replace the original (stock) directional stand-offs. To install the new directional stand-offs, perform the following. 3. See Figure 1. Insert a small screwdriver into middle hole (1) of license plate light cover assembly (2). Push forward to release tail lamp spring clip. -J03679 1 of 4 2 1 is01493 1. Middle hole 2. License plate lamp assembly Figure 1. Removing Tail/Stop Lamp Assembly 4. See Figure 2. Lift tail lamp assembly upward and disconnect tail lamp connector (1). Disconnect left (2) and right (3) turn signal 2-place connectors. 5. See Figure 3. Remove two left side fender support front socket head screws (1). Save hardware for installation. 6. Remove left fender support capscrew (2) (under fender) near end of support and washer (3). Remove capscrew (4) at approximate midpoint of fender support and washer (5). Save hardware for installation. 7. Remove directional lamp screw (6) and washer (7). NOTE Prior to removing turn signal wires, carefully note routing. In particular, pay close attention to the locations of cable straps which must be replaced. 8. Carefully remove fender support (8), turn signal lamp (9) and directional lamp support (10) along with wiring through elongated hole in fender (11). Discard directional lamp support and cap screw. Save turn signal lamp for installa- tion. 9. Perform Steps 5 through 8 for the right fender support and signal lamp assembly. NOTE At this point, the two turn signal pin terminals must be removed from the two-place connector in order to remove the turn signal and directional stand-off from the fender support. The pin terminals will be re-installed to the connector after routing wiring through new directional stand-off and installing stand-off and turn signal to fender support. Follow the instructions under AMP MULTILOCK CONNECTORS in the applicable Service Manual to remove the pin terminals from the two-place con- nector. 10. See Figure 3. Obtain new directional stand-off and cap- screw from kit. Route wiring from turn signal lamp (9) through new directional lamp support (10) and elongated fender support hole (11). Install capscrew (6) through fender support, new directional lamp support then into turn signal. Tighten capscrew securely. 1 3 2 is 01494 1.4-place tail/stop lamp connector 2. Left turn signal 2-place multi-lock connector 3. Right turn signal 2-place multi-lock connector Figure 2. Disconnect Tail Lamp and turn Signal Connectors 11. Perform step 10 for the right side

Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

ENGINE ASSEMBLY MANUAL 450i, ENGINE REPAIR STAND – 450i

0

Filed Under (Tips and Review) by admin on 28-11-2010

download
INSTALLING THE CLUTCH : æ Install the bronze bushing, the clutch basket, the spacer washer and the clutch hub. Install the conical washer, apply thread locking material to the threads and install the nut. Use tool #R447 to hold the assembly and tighten the nut to 150 Nm . æ Soak the friction discs in engine oil prior to installation. Alternatively install a friction disc followed by a metal disc until they are all installed, the last disc to be installed will be a friction disc. Install the clutch actuating rod, the clutch lifter piece, the needle thrust bearing and the thrust washer. Install the pressure plate, the six springs, the six washers and the six screws. Tighten the screws to 11 Nm . Tool #R447
Page 8 sur 26 æ Install the two locating dowels, install a new gasket, and note that Sherco uses a special gasket with an integrated silicone bead. Do not use gasket sealer on the mating surfaces as the sealer could plug the oil passages. Install the clutch cover and tighten the twelve screws to 11 Nm . o INSTALLING THE CAM CHAIN DRIVE GEAR ON THE LEFT HAND SIDE OF THE CRANKSHAFT: æ Using a thermal heat gun, heat the cam chain drive gear to ≈ 100°C , install the gear on the LH side of the crankshaft after installing the key, install the circlip. Use care to avoid damage to the end of the crankshaft. Page 9 sur 26 o INSTALLATION OF THE CYLINDER : æ Use a sharp chisel to remove any of the metal gasket that protrudes above the cylinder mounting surface.

YAMAHA XS650H/ SH Supplementary Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
Ignition timing check 1. Ignition timing is checked with a timing light by observing the position of the rotor pointer and the marks stamped on the timing plate. The timing plate is marked as follows. “ll” Firing range for No. 1 (L.H.) “T” Top Dead Center for No. 1, fL.H.1 cylinder 2. Connect the timing light to the left cylinder spark plug lead wire. 3. Start the engine and keep the engine speed as specified. Use a tachometer to check the engine speed. B. PICK-UP COIL ASSEMBLY The method of mounting the pick-up coil assembly is changed for easier service work. Thus, the followings “Pick-up coil assembly removal” and “Pick-up coil assembly reinstallation” should be changed. Pick-up coil assembly removal Remove the pick-up coil securing screws and remove the pick-up coil assembly. Pick-up coil assembly reinstallation Install the pick-up coil assembly on to the stator assembly. _ L 4. Specified engine speed: 1,200 r/min The rotor pointer should be within the limits of ” fl ” on the timing plate. If it exceeds the limits or does not steady, check the timing plate for tight- ness and/or ignition system for damage. NOTE: Ignition timing is not adjustable. C. FUEL LEVEL The carburetor is furnished with a drain screw to provide easy access to service work. Thus, the following “Fuel level measurement” should be added. Fuel level measurement NOTE: Before checking the fuel level, note the follow- ing: 1. Place the motorcycle on a level surface. 2. Adjust the motorcycle position by placing a suitable stand or a garage jack under the engine so that the carburetor is positioned vertically. 1. 2. Connect the level gauge (special tool) or a vinyl pipe of 6 mm (0.24 in) in inside diameter to the float bowl nozzle left or right side carburetor. Set the gauge as shown and loosen the drain screw 3. Start the engine and stop it after a few minutes of run. This procedure is neces- sary to obtain the correct fuel level. NOTE: Make sure the fuel petcock is “ON” or “RES” oosition. 4. Note the fuel level and bring the gauge to the other end of the carburetor line and repeat step 3 above. Note the fuel level again and compare it with the previous gauge reading. They should be equal. If not, place a suitable size of wooden piece or the. alike under the center stand and adjust. 5. Check the fuel level one by one. The level should be in the specified range.

Incoming search terms:

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

Incoming search terms:

Incoming search terms: