HARLEY DAVIDSON CHROME INSTRUMENT BEZEL COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
This kit is designed for installation on voltmeter, fuel gauge, oil pressure and air temperature gauges used on 1986 and later FLT and FLHT models. Kit Contents Table 1. Kit Contents Description Quantity Chrome bezel cover 2 Adhesive tape, double-sided strip 1 There are no Service Parts available with this kit. INSTALLATION NOTE Using a 50:50 mixture of isopropyl alcohol and water, wipe dirt, oil and grease off of instrument bezel and bezel cover before applying double-sided tape or tape may not adhere well. 1. See Figure 1. Cut tape (1) into six equal pieces. 2. Remove paper liner from one side of tape and apply tape to front face of gauge pressing firmly into place. Space all three pieces equally. 3. Remove outer liner from tape. 4. Place bezel over gauge and press firmly into place

HARLEY DAVIDSON INNER FAIRING TRIM PACKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Install Small Instrument Bezel Covers 1. See Figure 1. Cut tape (1) into six equal pieces. 2. Remove paper liner from one side of tape and apply three pieces tape (spaced equally) to the instrument bezel (2). Press firmly. 3. Remove the adhesive backing from the back of the double- sided tape. 4. Position instrument bezel cover (3) over gauge and press firmly into place. 5. Repeat for remaining gauges. Install Large Instrument Bezel Covers 1. See Figure 1. Cut tape (4) into sixteen equal pieces. Use eight pieces for each bezel cover. 2. Repeat Steps 2 through 5 under “Install Small Instrument Bezel Covers”. 4 5 2 1 6 3 is05418 1. Adhesive tape, double-sided (2) (cut into three pieces) 2. Instrument bezel 3. Chrome bezel cover, small (4) 4. Adhesive tape, double-sided (2) (cut into eight pieces) 5. Instrument bezel 6. Chrome bezel cover, large (2) Figure 1. Install Instrument Bezels Install Front Speaker Trim 1. Gently brush or vacuum each speaker grille to remove any dust or dirt particles. 2. Cut eight 1-inch strips of narrow masking tape. 3. Without removing the adhesive backing, position the trim rings against the speaker grille

HONDA NRX RUNE CALIPER COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Starting on the right side hold the cover in place over the brake caliper. See photo (1), note how the spring when installed wraps around the bleeder screw (1A) at the front of the cover. See photo (2), note how the spring at the rear of the cover is routed behind the brake pad retaining pin. Using one of the springs supplied hook both ends of the spring into the holes at the front edge of the cover. Clean the face of the caliper (area marked “Nissin”) with rubbing alcohol. Peel the backing from the adhesive tape on the inside of the cover. Carefully position the cover in place aligning it with the suspension arm and being sure it is seated flat against the caliper. Press firmly to secure the tape to the caliper. Next stretch the spring over the bleeder as shown in photo (1A). At the rear of the cover route the spring behind the brake pad retaining pin as shown in photo (2A). Hook the spring into the upper hole then using a piece of fine wire or string (dental floss works good) hook onto the open end of the spring as shown in photo (3). Pull the hook into the hole in the cover. Remove the wire or string. Check again to see that the cover is seated on the caliper and that the springs are secure and not interfering with the moving parts of the brakes. 2. Repeat on the left side caliper. Rear Caliper Cover 1. Set the cover in place over the caliper. Notice that you need to hook the top of the cover over the caliper and the location of the two small spring holes at the front and back of the cover. The long spring supplied will attach to the front hole, pass between the caliper housing and the backside of the brake pad, then attach to the rear hole

Incoming search terms:

TRIUMPH ROCKET III SWING ARM COVER INSTALLION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the º” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.

TRIUMPH ROCKET III SWING ARM COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 28-12-2010

download
1. Locate and remove the 6mm screw which secures the rear brake hose clip to the top of the swing arm (just in front of the lower right shock absorbers mounting point. 2. Notice the double faced adhesive tape on the inside of the cover and where it will contact the swing arm when installed, clean this area with rubbing alcohol and remove the backing from the adhesive tape on the inside of the cover. 3. Place the ¼” washer provided on the top of the swing arm over the brake hose clip mounting hole. Starting at the rear of the swing arm slide the cover carefully into place and align the small hole in the top of the cover with the washer and the threaded hole. Place the screw thru the hose clip then the cover and finally the washer, next thread the screw into the hole finger tight only. 4. Press the front area of the cover with the adhesive tape firmly into place. Tighten the 6mm brake hose clip screw securely.