1988-1989 ENGINES Toyota 1.6L 16- Valve 4 – Cylinder REMOVAL & INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
Removal 1) Mark and remove hood. Remove battery. Remove engine under cover (splash) shields. Drain coolant, engine oil and transaxle fluid. Mark and disconnect vacuum hoses and electrical connectors. 2) Remove air cleaner assembly. Disconnect coolant hoses. Mark and disconnect throttle, cruise, and kickdown cables (ifequipped). Mark and disconnect fuel inlet and return hoses. 3) Remove fuel tank protectors. Remove airflow meter assembly. Remove transaxle protector (if equipped). Remove accessory drive belts. Remove alternator. 4) Disconnect oil cooler hoses (if equipped). Disconnect power steering pump and A/C compressor and set aside (if equipped). Disconnect speedometer cable from transaxle. Remove clutch slave cylinder (if equipped). Mark and remove shift control cable(s). 5) Remove cruise control actuator assembly (if equipped). Raise vehicle and disconnect exhaust pipe from exhaust manifold.

2001 Toyota Echo L4-1.5L – Removal and Installation

0

Filed Under (Toyota Manuals) by admin on 17-06-2011

Download
REMOVE HOOD HINT: At the time of installation, please refer to the following item. Adjust the hood.
2. REMOVE WIPER ARM HINT: At the time of installation, please refer to the following item. Adjust the installation position of the wiper arms. REMOVE RH AND LH COWL TOP VENTILATOR LOUVERS 4. REMOVE NO. 2 CYLINDER HEAD COVER Remove the 4 nuts and No. 2 cylinder head cover. Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs.) 5. REMOVE BATTERY AND AIR CLEANER CASE ASSEMBLY WITH AIR HOSE

HONDA GL1000 DYNA S ELECTRONIC IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-04-2011

download
open the top and side compartments. Locate the two ignition coils and ballast resistor directly in front of the air cleaner intake. On some models it is best to remove the air cleaner for access to the coil area. Unplug the wires from the ballast resistor. Connect the power resistor supplied with the kit across (parallel with] the ballast resistor, and reconnect the wires to the tabs provided. The resistor will become very hot during operation. That is normal, and not destructive to the resistor, however, care should be taken to keep cables and wires from coming in contact with it. Locate the blinker relay just behind the fuse box in the left compartment. The white/green wire going to the relay carries 12 volts from the ignition switch. Using the splice connector provided, attach the separate red wire included in the kit to the white/green wire, as shown below. Do not strip the wires. On 197B and 1979 models, the 12 volts can be obtained at the accessory terminal in the left side compartment. y^T^^TL. PUSH CLIP DOWN RED WIRE SUPPLIED WITH KIT SWITCHED 12 VOLTS Remove the points cover and battery cover. Remove the 10 mm bolt holding the spark advance assembly to the engine. Remove the screws holding the points plate to the engine. Disconnect the blue/yellow
and yellow point wires where they plug into the wire harness and remove the entire point/plate assembly. Notice that there are two other wires connected where the points plugged in. These are wires going to the condensers mounted in front of the battery. Unplug both wires and tuck them back out of the way. Do not reconnect. | > Remove the spark advance assembly from the engine. Remove the point cam from the advance assembly. Coat the advance assembly shaft with oil. Place the OYNA S rotor on the shaft and while spreading the weights, push the rotor down until it engages the weights. Ensure that the rotor rotates freely on the shaft as the advance weights move out and back. Install the advance/rotor assembly on the engine making sure the pin on the camshaft is engaged in the slot on the advance assembly. Install the washer and bolt, and tighten. Ensure that the rotor is still free to rotate.

HARLEY DAVIDSON DECORATIVE TRIM FOR HEAVY BREATHER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION NOTES To avoid exposure to grease, oil, dust, dirt and skin oil, do not remove the backing film from the medallion or medallion insert until the moment of application. For maximum adhesive bond, the intake tube surface under and immediately surrounding the medallion must be clean and dry. 1. Clean the surface of the intake tube with a mixture of 50- 70 percent isopropyl alcohol and 50-30 percent distilled water. Allow to dry thoroughly. NOTE Ambient temperature should be 70-100 °F (21-38 °C). 2. See Figure 1. Remove backing film from medallion insert (1) and install on medallion (2). 3. With the backing film still in place, trial fit the medallion (2) to the intake tube. 4. Remove the backing film from the back of the medallion. Press the medallion firmly into position for about five sec- onds. 5. After releasing pressure, avoid direct contact with the medallion for at least 20 minutes. NOTE Allow AT LEAST 24 hours before exposing the air cleaner to vigorous washing, strong water spray or extreme weather. The adhesive bond will increase to maximum strength after about 72 hours at normal room temperature

HARLEY DAVIDSON EFI INTAKE MANIFOLD COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 1. Remove screw (A) that holds the air cleaner cover (B) and seal (C). 2. Remove three T27 TORX® screws (D) to release the cover bracket (E) from the filter element (F). 3. Remove the filter element, pulling the two breather tubes (G) from hole on the inboard side of element. 4. Remove the two breather tubes (G) from the fittings on the two cylinder head breather bolts (I). 5. Remove the two breather bolts (I) and O-ring seals (K) from the air cleaner backplate (J) with a 7/16 inch deepwell socket. 6. Remove the backplate and gasket (H) from the injection module. 7. Aligning the flat edge of a new cover gasket (2) with the backplate molded tab, install a gasket (2), chrome cover (1) and second gasket, in order, on the air cleaner back- plate. 8. Install the breather bolts through the air cleaner backplate. Re-install O-ring seals onto each breather bolt. Install a washer (3) from the kit on each breather bolt. Apply Loctite 243 to the breather bolts and align holes in the backplate with the holes in the cylinder heads and install the breather bolts. Use a 7/16 inch deepwell socket and alternately tighten the breather bolts to 120-144 in-lbs (13.6-16.3 Nm) . 9. Slide gasket over the sleeve on the inboard side of filter element. 10. Install breather tubes about 1/4 inch (6.4 mm) into holes on inboard side of filter element. 11. Install breather tubes onto fittings of two cylinder head breather bolts. NOTE Air cleaner mounting without installation of the breather tubes allows crankcase vapors to be vented into atmosphere in violation of legal emissions standards. 12. Place the filter element onto backplate, with the flat side down, so that the hole on the inboard side of element fits over the molded boss in the backplate. 13. Align holes in cover bracket with those in filter element and start three screws. Stamp on cover bracket points downwards. Use a T27 TORX drive head, alternately tighten screws to 20-40 in-lbs (2.3-4.5 Nm) . 14. Make sure that the rubber seal is proper seated around perimeter of air cleaner cover and place cover on back- plate. 15. Fit the air cleaner cover onto backplate. Apply Loctite 243 to the threads of air cleaner cover screw. Install screw through cover and tighten to 36-60 in-lbs (4.1-6.8 Nm)

Incoming search terms:

HARLEY DAVIDSON CRUISE CONTROL KIT FOR FLHR/I AND FLHRS/I MODELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove seat, left saddlebag, left side cover and air cleaner assembly following instructions in applicable Service Manual. 2. Review the CRUISE CONTROL-ULTRA MODELS section in the applicable Service Manual before attempting to install this kit. Install Cruise Control Module To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the appropriate Service Manual and remove bat- tery. 1 is04799 1. Cruise control module mounting hole (3) Figure 1. Battery Box (Right Side View) 2. See Figure 1. In battery box, identify the location of the three mounting holes (1) (on left side of panel) for mounting the cruise control module. 3. See Figure 10. Obtain the cruise control module (1) with cruise cable attached and three grommets (5) from kit. Install the grommets on studs of cruise control module with small diameters outward. 4. See Figure 2. While holding cruise control assembly in place near its mounting location, feed the cruise control cable through the hole in frame crossmember plate and route under rear spark plug wire staying on inner side of fuel line components. Carefully curve cable toward the right and continue routing up under the fuel tank and over the top of the engine stabilizer bracket, then down between cylinder heads. Leave in place temporarily. 5. See Figure 10 and obtain a harness retainer (4) from kit and secure the cruise cable to crossmember plate with barb as shown. On California models, remove the EVAP hose from cable clip and secure hose with one of the cable strap (8)

Incoming search terms:

HARLEY DAVIDSON CHROME LIFTER BLOCK COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your motorcycle is available at any Harley- Davidson Dealer. NOTE Removal of the air cleaner assembly and, in cases where the bike has forward controls, shifter linkage will aid in installation of this kit. Remove the air cleaner and, if necessary, shifter linkage by following procedures in the appropriate Service Manual. 1. Remove the two rear most screws on the rear lifter cover. 2. See Figure 1. Install rear lifter cover bracket (1) assembly using screws (2) removed in step 1. Torque screws to 90- 120 in-lbs (10.0 – 13.5 Nm). 3. Remove the two screws most forward on the front lifter cover. 4. See Figure 2. Install front lifter cover bracket (1) assembly using screws (2) removed in step 3. Torque screws to 90- 120 in-lbs (10.0 – 13.5 Nm)

SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

SUZUKI SV650/ S PERIODIC MAINTENANCE CHART

0

Filed Under (Suzuki) by admin on 26-02-2011

download
Item km miles months 1000 6000 12000 18000 24000 600 4000 7500 11000 15000 1 6 12 18 24 Air cleaner Spark plugs Tappet clearance Engine oil Engine oil filter Fuel hose Engine idle speed Carburettor synchronization Evaporative emission control system PAIR air supply system Throttle cable play Clutch cable play Radiator hoses Engine coolant Drive chain Brakes Brake hoses Brake fluid Tires Steering Front forks Rear suspension Exhaust pipe bolt & nut Chassis bolt & nuts – - – R R – I I I – - I I – - – I – - T T Replace every 4 years Replace vapor hose every 4 years – - I – I I I – - Replace every 2 years Clean & lubricate every 600 miles (1000km) Replace every 4 years Replace every 2 years R R R R – - R – I I R I I R I R – Inspect and adjust, clean

HARLEY DAVIDSON NOSTALGIC TWIN CAM 88 AIR CLEANER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1. Remove current air cleaner cover and screw. 2. See Figure 1. Coat threads of screw (1) from kit with Loc- tite® 243 (blue) (Harley-Davidson part number 99642-97). Install new air cleaner cover (2) with screw (1). If this kit will be installed with a Screamin’ Eagle Twin Cam 88 high flow air cleaner kit, place the self adhering gasket (must be purchased separately) inside the cover between the air filter and the cover. Tighten screw to 36-60 in-lbs (4.1- 6.8 Nm)