KAWASAKI 1500 9408 PRO HYPERCHARGER INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 26-04-2012

download
STEP 1 Remove the seat STEP 2 Disconnect the battery positive cable to prevent sparking that could cause ignition of spilled fuel, and personal injury. STEP 3 Remove the fuel tank. IMPORTANT- Throughout this installation, we strongly recommend labeling all hoses, and the nipples they were removed from. STEP 4 Remove the intake ductwork, air inlet, right and left air cleaner housings, air cleaner, cold start components (see PIC. 1), air mass sensor, and support bracketry. The wires that were unplugged from the cold start solenoids, may be neatly bundled and tucked out of harms way and out of sight. Be sure the terminals are insulated so they cannot short to any surrounding parts. Insert plugs (3/8″ x 1/2″ socket head bolts work well) into the two hoses that connected to the cold start circuit lines. (See PIC.2.) Also unplug the crankcase breather hose from the right angle fitting at the bottom of this enclosure, and the large diameter hose from the fresh air injection valve. (Don’t forget to label.) The fuel drain hose will not be re-used. PIC.3 shows what you’ll have left when all components are removed. STEP 5 From the hardware kit, find the front and rear support tabs and the four M6 x 1.0 x 16mm socket head cap screws. Install the support tabs to the threaded holes in each cylinder, and to the holes in the throttle body as shown in PIC.4. STEP 6 From the hardware kit, find the M6 x 1.0 x 16mm hex bolt and lock tab washer. Also find the intake gasket (oval shape with two large holes) and the manifold adapter body. See PIC.5. Screw the air temperature sensor into the back of the manifold adapter body. Place the intake gasket over the mouth of the throttle body so all holes line up. Insert the M6 hex bolt through the lock tab washer, and secure the adapter body to the throttle body, again making certain all holes line up perfectly. Tighten the hex bolt, but do not bend the lock tabs yet

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

2001-2003 YAMAHA XV16 MODELS FACTORY MODIFICATION CAMPAIGN

0

Filed Under (Yamaha) by admin on 02-12-2010

download
Fuel Pump and Carburetor Removal: •Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers. Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring.

Incoming search terms:

kawasakI 9400 hyPercharger kIt INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
steP 1 Remove the seat. steP 2 Remove the bottom of the three dash plaque bolts (8mm). steP 3 Lift up on the dash panel and unscrew the speedometer cable (knurled nut). steP 4 Unplug the three electrical connections. steP 5 With a 12mm socket, remove the tank-mounting bolt under the dash and at the rear of the tank. steP 6 Close the fuel valve and clamp off the fuel line. Disconnect the line from the fuel valve. steP 7 Raise the rear of the tank, and disconnect the two vent hoses, and remove the tank. steP 8 Refer to the section of your factory service manual that deals with removal and installation of the following components. • Remove the two round chrome “air cleaner covers”, their backing plates, the stock black plastic air box (air inlet under tank), and the crossover tube. • Remove the intake manifold to remove and crossover tube. Use extreme care when replacing the intake manifold. Uneven torque, damage to the intake gaskets, or contamination can cause an intake leak that will result in very poor running, and nearly impossible jetting!! • Unplug all hoses or lines from these components. You may want to label these hoses at this time. The Largest of these hoses (3/4″ I.D.) is for the fresh air injection system; the second largest (3/8″ I.D.) is the crankcase breather. The smallest of the hoses is a drain. steP 9 Remove the brackets that held each round backing plate. The right hand bracket is also a carb stabilizer. This function is duplicated with one of the included brackets. steP 10 Remove the carburetor according to the section in your factory service manual that outlines procedures for carburetor removal, disassembly, reassembly and installation. We recommend that you label each hose or fitting as they are removed to make reassembly easier. An example of hose labeling is shown in PIC. 1. carburetor re-jettIng Procedure note Different combinations of aftermarket exhaust and air cleaners will have a significant impact on carburetor jetting. The supplied jetting components have been tested and found to be a good combination to produce drivability and performance with stock or free flowing, muffled/baffled exhaust pipes. We highly recommend NOT using drag pipes (open style). Using drag pipes in conjunction with our air cleaner will require additional jetting above and beyond the components included in this kit. a) Consult your factory service manual for details of this procedure. We have supplied jets to cover many common configurations. Remove the four Phillips head screws securing the plastic carb top to the carb body. Carefully remove the plastic carb top making sure not to damage the rubber diaphragm.