HARLEY DAVIDSON AUTOMATIC COMPRESSION RELEASE TOOLS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Compressed air can pierce the skin and flying debris from compressed air could cause serious eye injury. Wear safety glasses when working with compressed air. Never use your hand to check for air leaks or to determine air flow rates. (00061a) Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) 4 3 6 5 6 1 2 7 is05443 1. Drill, 1.250 inch 2. Drill stop collar, 1.250 inch 3. Drill stop gauge 4. Socket head screw, 5/16 inch 5. Socket head screw, 1/4 inch 6. Dowel pin 7. Top plate Figure 1. Top Plate and Drill Bit Stop Collar Installation 1. Remove valves from cylinder heads. NOTE Do not allow the threaded studs to damage the gasket sealing surface of the cylinder head. 2. See Figure 7 and Table 1. Mount a cylinder head to the tooling plate (1). 3. Place a head bolt spacer (7) over each stock head bolt and lubricate threads and thrust faces, dowels and studs. Tighten head bolts in a crisscross pattern to 10 ft-lbs (13.5 Nm) . 4. See Figure 1. Align the top plate (7) bolt and dowel holes with the head hole pattern, Screamin’ Eagle logo towards the spark plug. This plate will only fit one way for the cylinder head it is being installed on. If the plate does not align with the head, turn it over keeping the logo towards the spark plug and install the cylinder head. 5. Lubricate the two dowel pins (6) and insert in the top plate and into the cylinder head. 6. Apply lubricant to the two socket head screws (4 and 5). Insert into their respective holes in the plate to the cylinder head and tighten to 5 ft-lbs (6.8 Nm)

TPM-20 SCREW ON VALVE-CAP SENSOR Installation

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
Deflate the tire and separate the tire-bead on the side of the bike that you plan to mount the Transceiver. o Squeeze the sidewall using ‘C’ clamps about 3″ (7.5cm) on each side of the tire valve. p Remove the existing tire valve and clean the hole prior to inserting the TPM-30 sensor. q Insert TPM-30 sensor so that the fill-port is on the opposite side of where the Transceiver will be. Install the sealing ‘O’ ring and then hand tighten the nut. Do not remove the black plastic bushing. r Torque the nut 4 – 6 ft-lbs (5.5 – 8.0 N meter) – just enough to prevent the Sensor from twisting in the tire valve hole. s Remove “C” clamps, lubricate the tire bead and inflate the tire. Check for any air leaks – use soapy water and look for air bubbles.

Air Shock Installation Instructions

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
Air HoseInstallation. Choose the most convenient loca- tiononyour motorcycle for the air fill valve. Drilla 5/16″hole and install the air fill valve as shown in Figure 3orsecure air fill valve to frame tube. 2. Keep hose ends clean during installation because dirt can cause air leaks. 3. Install hose connector, tube clamp and two O-rings onto one end of the air hose (See Figures4&5) Apply rubber lubricant (soap solution, not oil) to the O-rings to ease installation on the air hose& into the shock absorber inlet. Plastic connector should just bottom on fitting. Do not overtighten! The function of the nut is to hold everything together in place, the O- rings do the sealing. Fin- gertightenonly (10 in/lb maximum). 4. After routing the air hose, trim the length to fit air fill valve. Install hose connector, tube clamp, and twoO-rings onto end of hose (See figures 4&5). Lubricate as above and assemble to air fill valve. Use the same procedure formating hose. Important —leaveasmall amount of slack in hose near shock absorber to allow for the slight move- mentofthe shock. Caution! Do not install hose near ex- haustsystem, battery or any other sharp edges or seat movement. Keep hoses clear of moving parts such as wheels or suspension components. Do not allow hoses to have excess slack and sag below the motorcycle. The hoses could catch on road surfaces or debris and could be damaged while the motorcycle is in motion. 5. If necessary the air hose can be secured along the motorcycle’swiringharness with tie-wraps. 6. Testing: Inflate system to 50 psi. Apply soapy water solution to all connections and check for air leaks. If there are any leaks, disconnect the suspected fitting and check for dirt or damage to the air line or the O-rings. Remove any dirt or foreign matter, re-lubricate the O-rings and reinstall. If unable to locate the leak, remove rubber boot from shocks and submerge pressurized components under water (in- cludingT-Valve) and check for leaks. If you cannot solve the air leak problem, please contact our technical staff for assistance

BMW Motorcycle R1100/ 850 Model Throttle Cables

0

Filed Under (BMW) by admin on 16-11-2010

download
Problem: Engine surges at constant speed. Difficult to adjust and balance the left and right throttle bodies. Cause: Differences in opening and closing of the throttle butterflies caused by friction in the throttle cable. Remedy: 1. Fit a low friction throttle cable. 2. Check the following to ensure optimum results: Ignition timing Spark plugs (FR 6DDC) type / condition (reference SI 2739 in Main Group 12) Valve clearances Correct Cat. code plug Check throttle housing inlet manifold for air leaks 3. Synchronize the throttle butterflies as illustrated on the attached procedure. Note: Make sure there are no obstructions in the vacuum stub pipe prior to connecting the Synchro tool. Parts: 32 73 1 342 149 R 1100 RS 32 73 1 342 150 R 1100 RT, R, & GS Information: The Low friction throttle cable was introduced into series production as follows: R 1100 RS from 0312537 onwards (06/95 prod.) R 1100 GS from 0381479 onwards (06/95 prod.) R 1100 R from 6379238 onwards (06/95 prod.) R1100RT from 0440499 onwards (06/95 prod.) R 850 from the start of production Warranty: The BMW Motorcycle Limited Warranty will cover the replacement of the throttle cable for motorcycles in the affected VIN range. Authorization is not Required . File a warranty claim, using the following information: