2009 – Current Harley Davidson Trike Conversion Kit INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-02-2012

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect and REMOVE battery. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Remove and save the Passenger Handrail and two ¼ – 20 flanged hex head nuts if equipped. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove four ¼ – 20 HHCS. 13. Remove Tour Pak from Top Support Tube. 14. Remove both saddlebag support rails. 15. Loosen Muffler Clamps on both Mufflers and remove two 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 16. Remove right side rear heat shield. 17. Remove and discard Muffler Support Plates. 18. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip. 19. Remove four frame cover fasteners and the Left and Right Frame Covers. 20. Remove four Tour Pak Support fasteners and the Tour Pak Support.
7 21. Remove four rear fender fasteners and rear fender. 22. Remove four ½ – 13 HHCS and washers. Remove and discard Rear Air Shocks, Air lines and Air Valve bracket. 23. NOTE: NOTE: NOTE: NOTE: If motorcycle is A.B.S. Equipped refer to A.B.S. Installation Instructions. WARNING: WARNING: WARNING: WARNING: If A.B.S. Equipped DO NOT drain brake fluid. 24. Drain all Brake Fluid from the Rear Brake System. 25. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 26. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 27. Remove the Spring Clip and nut from the Rear Axle. 28. Remove Rear Axle and Rear Wheel Spacers. 29. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 30. Remove Rear Brake Caliper. 31. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate. 32. Remove Rear Wheel Assembly. 33. Remove two 3/8 – 16 SHCS. Remove Passenger Footboards.

HARLEY DAVIDSON TOURING SUSPENSION AIR PUMP KIT OPERATION/ INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
OPERATION 1. Remove cap from air suspension air valve and connect pump by threading the air valve adapter (1) on the pump as shown in Figure 1. When adapter is threaded properly, the current air pressure in the system will be indicated on the gauge of the pump. Do not exceed maximum air pressure for rear suspension. Air components fill rapidly. Therefore, use low air line pressure. Failure to do so may result in possible damage to components. (00165a) NOTES See the motorcycle’s Owner’s Manual or, if installed, the air suspension lowering kit’s instruction sheet for the recommended air pressures. Using pressures outside the recommended loading range will result in a reduction of available suspension travel and reduced rider comfort. 2. To increase pressure, operate the air pump handle (4) until the desired pressure is indicated on gauge (2). Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) NOTE The pressure release button is designed to release pressure slowly. If the button is completely or rapidly depressed, no air will be released. For the best results, depress the pressure release button slowly and only partially. 3. To decrease pressure, slowly depress the pressure release button (3) on the pump until desired pressure is indicated on gauge (2)

Incoming search terms:

HONDA CBX 750F (RC17) OWNERS MANUAL

0

Filed Under (Honda) by admin on 26-11-2010

download
Front air pressure adjustment: 1. Place the motorcycle on its centre stand. Do not use the side stand, or you will get false pressure readings. 2. Remove the front fork air valve cap (1). Check the air pressure. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 3. Add air to the recommended pressure. NOTE: We recommend that you do not exceed the recommended air pressure or the ride will be harsh and uncomfortable. 4. Reinstall the front fork air valve cap. Rear air pressure adjustment: 1. Place the motorcycle on its centre stand. 2. Do not use the side stand, or you will get false pressure readings. 3. Remove the right side cover. 4. Remove the valve air cap (2). Check the air pressure with an air pressure gauge. NOTE: Some pressure will be lost when removing the gauge from the valve. Determine the amount of loss and compensate accordingly. 5. If required, add air up to the recommended pressure. 6. Reinstall the air valve cap (2) and the right side cover

COMMANDER 1,000 LBS. CAPACITY MOTORCYCLE LIFT INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Your lift comes packaged as a single unit. A fork-lift, floor-jack or other heavy-lifting equipment may be necessary to separate the components. Exercise caution when disassembling the packaged lift, as shifting may have occurred during shipping. 2] Carefully unpack the lift. Check for any obvious shipping damage. (Remember to report any shipping damage to the carrier and make a notation on the delivery receipt.) 3] Carefully turn the table upright into operating position before removing shipping cable restraint from scissor mechanism. 4] Connect foot-operated air valve to 100 psi maximum air supply. The lift may be damaged and/or personal injury may result if the pressure exceeds the maximum 100 psi rating. 5] Stand clear of lift table, and depress the “UP” side of the foot valve to raise the table. 6] To lower table, lift locking bar from safety latch and lower to next position, or to the floor. 7] Place drop-out cover over drop out opening. 8] Insert ramp mounting pins into holes at either end of table to mount ramp. NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise. OPERATION and MAINTENANCE 1] Loads must be centered on table at all times. Table is rated for a maximum load of 1,000lbs. 2] Loads must be firmly positioned and secured on table at all times. 3] All moving parts have been lubricated at the factory and should be re-lubricated every six (6) months to prevent problems. Grease points are located at each end of frame pivot shaft and at top ends of inside frame assembly. 4] Lightly oil cylinder rod when it becomes dry. 5] Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every six (6) months. 6] Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly.