Suzuki C50/ M50 Boulevard BIG AIR KIT INSTALLATION

0

Filed Under (Suzuki) by admin on 13-03-2012

download
1. Remove the (2) Bolts at the top of the stock air cleaner to the left and right of the oval rubber hose coming from under the fuel tank. 2. Loosen the hose clamp at the base of the oval rubber hose on the top of the air cleaner. 3. A male barb protrudes from the rear of the air cleaner that inserts into a rubber grommet mounted to the cylinders. Pull the air cleaner away from the cylinders firmly and you will feel the barb release. Now pull the upper section of the air cleaner downward to remove it from the oval snorkel tube from under the fuel tank. 4. Now you can reach to the rear of the box and unplug the electrical lead for the Air Sensor” which sits just about in the middle of the rear of the air cleaner. Now remove the breather hose at bottom of the air cleaner. 5. Set the air cleaner aside and turn it over to access the back. Remove the single bolt that secures the Air Sensor” (This sensor will be installed into the Aluminum Manifold of your new BAK assembly later) 6. Remove the lower mounting arm assembly from the cylinders. (You will not reuse this). 7. Using the (2) Dome head m6 x 15mm screws install the (2) #1 Arms to the rear (the side without the groove) of the backing plate, the shiny/chrome side of the arms should face outward. The smaller of the two holes in each arm is the one you place the screws through. Use the m6 Flange Nuts to secure the bolts at the rear of backing plate. Snug these up but do not tighten fully.

Incoming search terms:

SUZUKI Hayabusa, GSXR 1000, GSXR 750, GSXR 600 Sport Brake Lever INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 21-02-2012

download
Before you install your new ASV brake lever, you MUST choose the correct brake light switch tab to install. You will find in the package with this lever one plastic bag with four smaller bags inside of it. One bag has two small phillips screws. The other three bags have small black aluminum blocks (light switch tabs) with labels on them. Part# BRC511-H is ONLY for HONDA motorcycles. Part# BRC511-STK is for all SUZUKI, TRIUMPH and 05-06 KAWASAKI ZX636R motorcycles ONLY. Part# BRC511-K is for all KAWASAKI motorcycles EXCEPT the 05-06 ZX636R . Choose the correct tab for your bike and install it onto the lever as shown in photo 2b using the two small Phillips head screws provided. It is recommended that you use locktite or another type of thread locking adhesive to make sure these screws do not come loose. Be sure to tighten these screws as tight as you can without stripping them. The brake stop / light tab is required for your ASV brake lever to work properly Carefully place the lever into the master cylinder while inserting the plunger rod into the barrel hole as shown in photo 4. Install the main pivot bolt, and tighten it until it is snug against the master cylinder. Do not over-tighten, as it could cause the lever to bind in the master cylinder

Toyota Truck Park Brake Bellcrank Repair

0

Filed Under (Toyota Manuals) by admin on 01-10-2011

download
Toyota trucks including Tacoma, T100 and Tundra with rear drum brakes use a bellcrank apparatus through the brake backing plate as part of the parking brake system. These bellcranks, made of aluminum and steel are known for seizing up. The photo below (fig.1) shows the tell tale sign of a seized bellcrank, this one being on the right side. The sagging cable that runs across the differential is a warning. If you notice this you need to check the action of the bellcranks before using the parking brake further. Using the parking brake with this condition can cause damage to the brake shoes and drum.
2 Removing Toyota Drums If you have never removed your drums, you will likely find that they are stuck in place. Rust tends to build up between the drum and hub flange making them difficult to remove.

1995 – 2004 Toyota Tacoma Body Lift Kit Installation and REMOVAL

0

Filed Under (Toyota Manuals) by admin on 24-09-2011

Download
RADIATOR FAN SHROUD: Only raise body high enough to remove and replace body mounts. Always watch the fan shroud for sufficient clearance when raising the body. 2. Remove the 12mm bolts and nuts from the upper steering coupler on the rack and pinion noting the position of the steering column. Note: do not let the steering column turn, keep the column and rack aligned to its original position, mark if necessary. See figure 2. 3. Loosen body mount bolts on the driver’s side of vehicle and remove bolts from opposite side for positions 1,2 and 3, see Figure 1. Place a 2×4 between the jack and body to pread out load. 4. Raise the body on the driver’s side just far enough to remove mounts. Temporarily prop up the cab between cab and the frame with a wooden 2×4 or spacer. (This is to avoid cab from falling while working on body mounts.) The bolts on the opposite side will help ensure that the body does not shift. Make sure cab doesn’t contact bed when lifting. 5. Remove factory mounts one at a time.
6. Install the new S10321 steel bracket, polyurethane body mounts, and steel sleeves in positions 1, 2 and 3. Refer to the diagrams for positions. NOTE: On 2001 and newer models you will need to invert the #2 position bushings so that the M02787 is on top. 7. Install the supplied aluminum steering coupler with the round bosses pointing down. Note: you may have to loosen the pinch bolt at the top of the steering coupler so that it will slide up enough to install the steering coupler. See figure 2. 8. Lower the driver’s side and START the new bolts into the new mounts. Reconnect the steering coupler with the supplied 5/16” bolts from the top and nuts. DO NOT TIGHTEN!
9. Now remove bolts from passenger side of vehicle and repeat steps 3 through 6. 10. Tighten the steering coupler bolts and nuts to 35ft lbs also tighten the upper steering bolt to 35ft lbs

Incoming search terms:

HARLEY DAVIDSON SPORTSTER ALUMINUM SHIFT LINKAGE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. See Figure 1. Remove stock capscrews (4) and stock shifter rod (2). Discard stock capscrews. 2. See Figure 2 and Table 2. Loosen the lock nuts (5) and turn the rod ends on the new aluminum shifter rod (1) to match the length of the stock shifter rod. 3. See Figure 2 and Table 2. Slide longer capscrew (3) through the front rod end of new shifter rod (1). Place rod on the outside of the lever assembly. Thread capscrew (3) into the lever assembly. 4. Slide shorter capscrew (2) through the rear rod end of new shifter rod (1). Place rod on the outside of the transmission shift lever. Thread capscrew (2) into the transmission shift lever. 5. Tighten capscrews to 10-15 ft-lbs (13.6-20.3 N-m) . 6. Firmly tighten the lock nuts (5) against the rod ends to 20- 24 ft-lbs (27.1-32.5 Nm) . 1 4 2 4 3 is05394 1. Lever assembly 2. Shifter rod 3. Transmission shift lever 4. Capscrew Figure 1. Shift Linkage Components

HONDA GL1100 Manifold Cover Installation Manual

0

Filed Under (Honda) by admin on 04-03-2011

download
Note: Read instructions carefully before installing. 1. Start with right side. Remove (2) screws and washers from each manifold tube base. NOTE: Save this hardware it will be reused. 2. Remove (4) screws and washers that hold chrome wire guide to carbs. 3. Apply a small amount of grease to the No. 10 washers (4). This will help to hold them in place on installation. 4. Place the No. 10 washers over the threaded holes in the carb base. 5. Reinstall the OEM wire guide and carefully insert 20 mm screws and lock washers. NOTE: The screws DO NOT go through the tube on the manifold covers. 6. Sandwich the tabs on the manifold cover between the carb top and the wire guide. Finger tight the screws. NOTE: Route spark plug wires OVER THE TOP of the wire guide. 7. Lift bottom of manifold cover and insert aluminum washers removed in step 1. Put smooth of washers toward manifold. You may have to use small amount of grease on these washers also to position them. 8. Position manifold cover and reinstall (2) OEM screws removed in step 1 9. REPEAT STEPS FOR THE OTHER SIDE.

HARLEY DAVIDSON SISSY BAR SIDE PLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION NOTE When removing rear fender reflectors, be careful not to damage fender paint. 1. Carefully remove the rear reflector. Remove any remaining adhesive from the back side of the reflector and any adhesive from the side of the fender. 2. See Service Parts Illustration. Remove the screws, washers, locknuts and clipnuts that attach the fender support cover and fender support to fender. Discard the button head screws but retain the washers (A), locknuts (B,C) and clipnuts (D) for installation. NOTE Prior to performing the following step, obtain a little slack for the turn signal assembly by reaching under the fender and bending open the aluminum tab on the clip securing wiring to fender. 3. Remove the locknut (B) from the turn signal stud (E) and gently remove the turn signal assembly from fender support cover, fender support and fender. Save locknut for installation. The turn signal will remain loosely attached to motorcycle by rear directional wire. 4. Carefully position the side plate between fender support and fender. While holding sideplate in position, line up the screw mounting holes and make sure the turn signal wiring passes through the cutout (slot) in the side plate. Coat threads of screws (1 and 2) from kit with Loctite 243 (blue) (Harley-Davidson part number 99642-97) and install locknut and clipnut, however do not tighten completely. 5. Add Loctite 243 (blue) (Harley-Davidson part number 99642-97) to turn signal stud and install through fender support cover, fender support, side plate and fender. Install locknut and tighten to 8-13 ft-lbs (11-18 Nm). Making sure sideplate remains aligned, return to fender support screws and tighten to 8-13 ft-lbs (11-18 Nm). 6. Reach under fender and position turn signal wiring into tab on clipnut. 7. Obtain reflector (3) from kit. Peel off protective strip backing and firmly press reflector (3) to side plate (4), centering reflector horizontally and vertically. 8. Repeat steps 1 through 7 on opposite side of fender

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

HARLEY DAVIDSON STREAMLINER FOOTPEG KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
NORMAL TOOTH WARRANTY This extended warranty applies only to the normal wear that will occur to the tooth profile geometry on the rear belt sprocket. Normal wear is considered wear that occurs when the protective hard coating has worn away exposing the underlying aluminum, changing the profile of the sprocket tooth significantly. Warranty is for five years from date of purchase with unlimited mileage. Warranty claims will require a dated receipt showing proof of purchase from an authorized Harley-Davidson Dealer. Warranty only applies to original purchaser of the sprocket. Original owners name must appear on the receipt. All applications of the sprocket require installation of upper and lower original equipment belt guard, or Harley-Davidson accessory belt guards where applicable. Warranty is voided if these items are not installed. Excessive chips found in the tooth profile due to abnormal riding conditions will void warranty. Occasional chips in the tooth are to be considered normal and should not be considered a warranty issue. Decorative external chrome carries the standard parts and accessories 90 day warranty. Staking the flange on the backside of the sprocket will pierce through the chrome, this is to be considered a normal process and should not be considered an issue. All warranty claims must be pursued through your authorized Harley-Davidson Dealer

HARLEY DAVIDSON SOFTAIL SPROCKET KIT INSTALLATION NOTES

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
NORMAL TOOTH WARRANTY This extended warranty applies only to the normal wear that will occur to the tooth profile geometry on the rear belt sprocket. Normal wear is considered wear that occurs when the protective hard coating has worn away exposing the underlying aluminum, changing the profile of the sprocket tooth significantly. Warranty is for five years from date of purchase with unlimited mileage. Warranty claims will require a dated receipt showing proof of purchase from an authorized Harley-Davidson Dealer. Warranty only applies to original purchaser of the sprocket. Original owners name must appear on the receipt. All applications of the sprocket require installation of upper and lower original equipment belt guard, or Harley-Davidson accessory belt guards where applicable. Warranty is voided if these items are not installed. Excessive chips found in the tooth profile due to abnormal riding conditions will void warranty. Occasional chips in the tooth are to be considered normal and should not be considered a warranty issue. Decorative external chrome carries the standard parts and accessories 90 day warranty. Staking the flange on the backside of the sprocket will pierce through the chrome, this is to be considered a normal process and should not be considered an issue. All warranty claims must be pursued through your authorized Harley-Davidson Dealer

Incoming search terms: