2004 CBR 1000RR CYLINDER HEAD COVER INSTALLATION

0

Filed Under (Honda) by admin on 17-12-2011

download
COLOR TABLE MARCH, 2004 ©2004 American Honda Motor Co., Inc. 9 When ordering a colored part: 1. Confirm the color code for the required part from the color table according to the part name and color type. 2. Select the corresponding part number from the appropriate PAGE/GRID. 3. Parts marked “X” are unused. 4. “*” = Basic Part Number, no extension (i.e. ZA, ZB). CBR1000RR’04 2004 No. COLOR CODE BASE COLOR NH1 Black NH1 R258B Winning red R258 NH411B Force silver metallic NH411M A R E A DESCRIPTION BASIC PART NO. 1CLIP, PANEL FIXING 91549-MW0-790 ZA ZA ZA 2COWL (UPPER) 64211-MEL-000 ZA ZB ZC 3COWL SET, L. (LOWER) (WL) 64450-MEL-670 ZF ZG ZH 4COWL SET, L. MIDDLE (WL) 64350-MEL-670 ZA ZD ZE 5COWL SET, R. (LOWER) (WL) 64400-MEL-670 ZF ZG ZH 6COWL SET, R. MIDDLE (WL) 64300-MEL-670 ZA ZD ZE 7COWL SET, RR. SEAT (WL) 77210-MEL-010 ZE ZF ZG 8FENDER, FR. 61100-MEL-000 ZA ZC ZB 9FRAME 50100-MEL-670 ZAZAZAA 10 FRAME 50100-MEL-770 ZA ZA ZAAC 11LABEL, COLOR 87565-MEL-000 ZD ZE ZF 12MARK, COWL (LOWER) 64819-MEL-000 ZD ZE ZB 13MARK, L. TOP SHELTER 64852-MEL-000 — ZA ZC 14MARK, L. TOP SHELTER 64856-MEL-000 ZA — — 15MARK, MIDDLE COWL 64811-MEL-000 ZA — — 16MARK, R. TOP SHELTER 64851-MEL-000 — ZA ZC 17MARK, R. TOP SHELTER 64855-MEL-000 ZA — — 18MARK, RR. SEAT COWL 64841-MEL-000 ZA ZB ZD 19MARK, RR. SEAT COWL 64842-MEL-000 ZA ZB ZD 20RAIL ASSY., SEAT 50200-MEL-010 ZA ZA ZA 21SHELTER SET, TOP (WL) 83150-MEL-670 ZA ZD ZE 22STRIPE A, L. MIDDLE COWL 64814-MEL-670 — ZC ZA 23STRIPE A, R. MIDDLE COWL 64813-MEL-670 — ZC ZA 24STRIPE C, L. MIDDLE COWL 64817-MEL-670 — ZA ZB 25STRIPE C, L. MIDDLE COWL 64818-MEL-670 — ZA ZB 26STRIPE, L. TOP SHELTER 64854-MEL-000 — ZB ZB 27STRIPE, R. TOP SHELTER 64853-MEL-000 — ZB ZB 28STRIPE, WINDSCREEN 64805-MEL-000 ZA ZA ZA 29WHEEL SUB-ASSY., FR. 44650-MEL-000 ZA ZA ZA 30WHEEL SUB-ASSY., RR. 42650-MEL-010 ZA ZA ZA 31WINDSCREEN SET 64250-MEL-000 ZA ZA ZA

2007 CBR1000RR REPSOL EDITION SET-UP INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
1. Remove the crate cover and check for damage. The CBR1000RR Repsol Edition is crated at the factory in either a covered or uncovered crate. You may receive either one. Polypropylene covered crate: Cut the strap, open the  fastener, and remove the polypropylene cover. Carton covered crate: Cut the strap and remove the carton cover. Remove the cardboard top. Uncovered crate: When stacking, protect the motorcycle from falling objects and bad weather. Check the unit for damage. If damage is found, follow the instructions on the Delivery and Damage Claims Guidelines wall chart (Reorder No. S0477) before proceeding further. 2. Remove the parts carton. Cut the strap and remove the parts carton from the crate base. Keep the You and Your Motorcycle – Riding Tips & Practice Guide booklet separate and hand deliver to the customer at the time of delivery 4. Remove the shipping bracket nuts and plate. Remove the nuts and plate that attach the front shipping bracket to the upper shipping brace. 5. Remove the rear  shipping brackets. While supporting the rear shipping brackets, remove and discard the nuts, bolts, and rear shipping brackets on both sides of the motorcycle. Install and torque the 8 x 22 mm socket bolts to secure the passenger footpeg brackets. Torque: 37 N·m (3.8 kgf·m, 27 lbf·ft) 6. Lift off the crate frame. Remove the bolts that attach the crate frame. Using two people, carefully lift off the crate frame. Use extreme care not to damage the motorcycle while  removing the crate frame. 7. Remove the front shipping bracket. Being careful not to damage the upper cowl, remove the bolts and front shipping bracket. Install the top triple clamp caps. PARTS QTY Socket bolt 8 x 22 mm 2 PARTS QTY
Top triple clamp cap 2 UPPER SHIPPING BRACE NUTS PLATE 8 x 22 mm SOCKET BOLT REAR SHIPPING BRACKET BOLT NUT BOLTS FRONT SHIPPING BRACKET CAPS BOLTS Page 8 İ2007  5 8. Relocate the ignition keys. Remove the ignition keys and protective tube from the throttle cables. Remove the packaging from the keys and insert one of them into the ignition

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

HONDA 2002-2004 GL1800/A Linked Braking System (LBS) Proportional Control Valve (PCV) Leakage

0

Filed Under (Honda) by admin on 25-11-2010

download
1. Pump the rear brake pedal four times. •If the brake pedal feels spongy, bleed the brake system per the Service Manual. After verifying proper brake system operation, proceed to step 2 below. •If the brake pedal does not feel spongy, proceed to step 2 below. 2. Place the motorcycle on its side stand, with the handlebars in the full left position . Lock the handlebars. 3. Place a scissor jack directly under the left front brake caliper as shown in the illustration. To avoid damage to the caliper, place a protective piece of rubber (such as a piece of inner tube) between the caliper and the jack. Wind up the jack until the front wheel is approximately 15 mm off the ground. 4. Measure the distance from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). Record this measurement . • If the measured length is 30.3 mm, replace the PCV per the Service Manual. (This length indicates the unit’s secondary master cylinder is fully stroked, which means there is no hydraulic brake pressure acting on the PCV.) After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. •If the measured length is longer than 30.3 mm , proceed to step 5 below. • INSPECTION/REPAIR PROCEDURE Record this measurement. Pump the rear brake pedal four times.
GL1800/A #16 ©2005 American Honda Motor Co., Inc. – All Rights Reserved 3 of 6 FEBRUARY 2005 5. Wait 30 minutes. Do not disturb the motorcycle in any way during this time. 6. Measure the distance again from the secondary master cylinder piston mounting bolt to the edge of the secondary master cylinder body (rod length of the secondary master cylinder). •If the measurement has decreased more than 1 mm from the measurement you recorded, proceed to step 7 below. •If the measurement is within 1 mm of the measurement you recorded, the PCV is OK. Proceed to the IDENTIFICATION section of this Service Bulletin. 7. Check the PCV for leakage. • If the PCV is leaking , replace the PCV per the Service Manual. After replacing the PCV, proceed to the IDENTIFICATION section of this Service Bulletin. • If the PCV is not leaking , you must diagnose the brake system problem before proceeding. After you have diagnosed and repaired the brake system, proceed to the IDENTIFICATION section of this Service Bulletin. NOTE: Any brake system problem not related to the PCV that is found while performing this Service Bulletin is not covered by this Safety Recall. If the motorcycle’s original factory warranty is still in effect or under HPP, file a normal warranty claim. If the unit is outside its factory warranty period or HPP coverage, contact TechLine for goodwill consideration. 8. Verify proper front and rear brake operation by pumping the front brake lever and rear brake pedal before riding the motorcycle

Honda Motorcycle Digital Audio System Owner's Manual

0

Filed Under (Honda) by admin on 22-11-2010

download
Applicable portable audio unit A commercially available portable audio player with a stereo mini jack terminal can be connected to this accessory. (An attachment kit designed for the model is necessary to connect the portable audio player to this accessory.) American Honda Motor Co., Inc. recommends you use a shock-resistant portable audio player such as a flash-memory player (e.g. MP3, etc.) or an MD player equipped with sound skip prevention function. American Honda Motor Co., Inc. also recommends you always ride your motorcycle safely on paved roads, because sound skip can occur during riding on rough roads. Refer to the following instructions on storage and handling of the portable audio unit. This accessory is not designed to operate the portable audio unit connected to the accessory. Refer to the portable audio unit manufacturer’s Owner’s Manual for how to operate the portable audio unit and operate it accordingly. Note that the warranty of this accessory does not cover function and failure of the portable audio unit connected to the accessory 5 Storage of portable audio unit connected to this accessory After connecting the digital audio system, put the portable audio unit in a stable place where it does not interfere with riding the motorcycle (e.g. in the sold separately front pouch, tank belt pocket, etc.) in a place free from vibration as much as possible. Do not place the portable audio unit in your pockets or clothes while connected to this accessory. The portable audio unit can vibrate and contact other materials while riding, causing a sound skip. To prevent such skips, store the portable audio unit in a suitable place while protecting it from vibration and shock by covering it with cushioning material. (Protect the remote control and peripheral devices as well as the portable audio unit.) Any system failure and damage to the portable audio unit and its peripheral devices are not covered by the warranty of this accessory.

Incoming search terms: