Harley-Davidson wheel installation kits

0

Filed Under (Harley Davidson) by admin on 19-04-2012

download
ReAcToR Five-SPoKe cuSTom wheel The five slim spokes of this custom wheel dramatically change the look of the VRSC™ motorcycle. Available in mirror-chrome or gloss black, the “ball-milled” spokes radiate from the unique center hub to blend with the machined rim, opening the bike for a light, sporting profile. The smooth curving rim, highlighted with machined grooves, adds to the true custom look without compromising strength or performance. The raised bosses on the hub carry the Original Equipment floating brake rotors, and add to the clean appearance of the installed wheel. 19″ Front Fits ’02-later VRSC models. Requires separate purchase of model-specific Wheel Installation Kit. ’07 VRSCX, ’08 VRSCAW Anniversary models, and other models equipped with laced front wheels also require additional purchase of (2) Front Brake Rotors P/N 44553-06A. 43219-08 Chrome. $1,119.95 43501-08 Gloss Black/Orange Stripe. $1,119.95 18″ Rear (240 Tire) Fits ’07-later VRSC models (except ’07-’08 VRSCD and ’07 VRSCR). Requires separate purchase of model-specific Wheel Installation Kit. 43728-08 Chrome. $1,399.95 43616-08 Gloss Black/Orange Stripe. $1,399.95 18″ Rear (180/55 Tire) Fits ’02-’06 VRSCA and VRSCB models, ’06-’08 VRSCD and ’05-’07 VRSCR models. Requires separate purchase of model- specific Wheel Installation Kit. 43215-08 Chrome.

HARLEY DAVIDSON DYNA CHROME COIL COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Installation 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Note the position of each spark plug wire in the ignition coil, then disconnect the two wires. 3. If there is an existing coil cover: Remove and discard the coil-cover mounting screws and spacers. Remove and discard the coil cover. If there is not an existing coil cover: Remove and discard the two coil mounting screws. 4. See the Service Parts illustration. Obtain the coil cover bracket (3), two long screws (4) and two spacers (2) from the kit. 5. Insert the screw into one of the holes in the bracket as shown, through a spacer, and into a coil mounting hole. Repeat with the second screw and spacer. 6. Assemble the coil to the electrical caddy with the two screws. Tighten the screws to 50 in-lbs (5.6 Nm). 7. Obtain the new chrome coil cover (1) from the kit. Position the cover over the coil, and fasten to the coil cover bracket with the three chrome screws (6) and washers (7) from the kit. Do not fully tighten the screws at this time. 8. Connect the spark plug wires through the holes in the side of the coil cover onto the correct coil terminals. 9. Adjust the cover to center the spark-plug wire boots in the coil cover holes for best appearance. Tighten the three chrome screws securely 10. Refer to the Service Manual and follow the instructions given to install the maxi-fuse

Incoming search terms:

HARLEY DAVIDSON TRIKE CHROME REAR GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Set the vehicle parking brake, open the trunk door and remove the trunk liners. 2. See Figure 1. From inside the trunk, locate four screws with washers (A) in the floor of the trunk compartment that hold the body to the rear frame. Leaving the washer in place, remove one of the screws and discard. 3. Obtain a long hex head cap screw (3) from the kit. Apply a few drops of Loctite – Blue to the threads of the screw, about 0.75 in (19 mm) from the screw head (C). 4. Insert the screw through the washer (A) and trunk floor. Thread it all the way through the U-channel on the outboard side of the rear frame (B), but do not fully tighten at this time. 5. Repeat for the remaining three screws. 6. Tighten all four screws to 18 ft-lbs (24.4 Nm) . 7. With an assistant, position the trunk rail assembly to the underside of the frame, fitting the four holes in the rail mounting brackets onto the threads of the screws installed in Step 4. 8. Apply a few drops of Loctite – Blue to the threads of each lock nut (4). 9. Install a washer (5) and locknut to the threads of each screw to hold the rail in place, but tighten only enough so the rail lightly contacts the frame. 10. Align the rear guard evenly to the contour of the lower body for best appearance, and adjust the position of the rail to provide clearance between the rail and the rear of the vehicle body. 11. With an assistant firmly holding the screw heads inside the trunk to keep them from turning, tighten the four lock nuts to 18 ft-lbs (24.4 Nm) . 12. Install an insert (2) into each end of the rear guard. Push firmly until fully seated.

HARLEY DAVIDSON PREMIUM TOUR-PAK LUGGAGE RACK KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
INSTALLATION Template Positioning (Rack Installation WITH SPOILER only) The location of the luggage rack has a direct relationship to the location of the Tour-Pak® Spoiler. The template (7) included in this kit will locate the luggage rack in the correct position for the current or future installation of a Tour-Pak Spoiler. NOTE A template is not required if installing rack without spoiler. 1. If a spoiler is already installed, or if the installation of a Tour-Pak-mounted spoiler may be desired in the future, cut the template along the appropriate line. 2. Carefully place the trimmed template on top of the Tour- Pak, aligning the edges of the template with the top surface of the Tour-Pak lid. Tape the template to the lid in the desired location. The template will help to properly locate the rack so that a spoiler may be added in the future. Rack Installation on Tour-Pak 1. ALL installations: Open the lid, and remove all loose contents from the Tour-Pak. 2. See Figure 1. Slip the mounting pads (2) onto each of the mounting bosses (B) of the luggage rack (1). NOTES Kit 53665-87: Position rack with wide upright toward rear of vehicle. Kit 91793-85: Position rack with upright toward rear of vehicle. Carefully center the rack from left to right, and position the rack squarely on the lid for best appearance. Do not mount the rack too far forward to avoid contact with the backrest pad. 3. Position the rack on the Tour-Pak lid in the desired loca- tion. 4. Carefully raise the rack, and place masking tape (A) on the Tour-Pak lid where the four mounting bosses contact the cover. 5. Lower the rack onto the tape in the location chosen in Step 3. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting boss. Remove the rack, and use a ruler to mark the exact center position of each mounting boss on the tape. 6. Drill four 1/16 inch (1.5 mm) diameter pilot holes through the masking tape and Tour-Pak lid at each mounting boss center position. Use a 9/32 inch (7 mm) diameter bit to drill the finish holes. 7. Remove the masking tape

Incoming search terms:

HARLEY DAVIDSON SKULL SHIFTER PEG/ HEEL REST PAD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
Models Shifter Peg Kit, Part Number 34689-04 is designed for installation on all model Harley-Davidson motorcycles. Heel Rest Pad Kit, Part Number 34699-04 is designed for installation on all models equipped with a Heel Rest Kit, Part Number 50227-01 or 50236-01. INSTALLATION Shifter Peg 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Using the screw (5), attach the peg (1) and tread (3) assembly to the shift lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). Heel Rests NOTE The chrome heel rest covers are side-specific. For best appearance, install so the HARLEY-DAVIDSON text is above the skull, and the MOTORCYCLES text below . 1. See Figure 1. Using the screws (5), attach the left-side heel rest (1) and tread (3) assembly to the left-side heel rest lever. Tighten the screw to 12-14 ft-lbs (16.3-19 Nm). 2. Repeat for the right-side heel rest (2) and tread assembly

Motorcycle Hand Warmer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Disconnect the Positive (+) terminal from the battery. 2. Remove the existing grip from the Clutch side. Removing the grip may require blowing compressed air in the end between the grip and the bar, injecting brake cleaner fluid, or cutting it off. 3. Clean the handlebar where the grip was removed with alcohol or a solvent to remove all residue and dry with a clean cloth. 4. Determine where the Clutch side heater will be mounted. Take the heater marked “Clutch” and place it on the handlebar approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 9:00 o’clock or they can be positioned on the bottom for appearance. Peel off the release paper and adhere the heater to the handlebar with the wires toward the headlight. 5. Apply a high temperature adhesive (such as JB Weld) to the inside of the Clutch side grip. Install the grips over the heaters and let the adhesive cure as instructed by the adhesive manufacturer. 6. The Throttle side heater is installed on the throttle sleeve under the rubber cover. Remove the rubber cover that is installed over the throttle sleeve so the Throttle side heater can be applied. Some of the throttle sleeves have ribs which need to be cut or ground off so the heater can make full contact with the sleeve surface or it will over heat in the void areas. 7. Determine where the throttle side heater will be mounted. Take the heater marked “Throttle” and place it on the throttle sleeve approximately ½” from the end and decide the position of the wires. It is recommended to mount the heater so the wires are at 3:00 o’clock with a loop to allow for the twisting motion of the throttle. Peel off the release paper and adhere the heater to the throttle sleeve with the wires toward the headlight. 8. Apply a thin coat of adhesive (such as J.B. Weld) to the surface of heater only and reroll the rubber hand grip over the entire throttle sleeve. Wipe off any excessive adhesive that may have rolled out