Honda TRX 450R 2006 Rear Grab Bar INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2011

download
To avoid injury or damage to your ATV, read these instructions before installation. 1. Parts List: Item Part Name Description Qty 1 H062060 Grab Bar 1 2. Preparation: a) Lock rear brake on bike. b) Remove OE grab bar, retaining all mounting hardware. c) Remove 3 OE rubber grommets from OE grab bar. 3. Installation: a) Install 3 rubber grommets on Pro Race Grab Bar.. b) Install Pro Race Grab Bar on bike, reusing all hardware and mounting locations. 4. Maintenance: Check fasteners for tightness and re-torque as required. 5. Care and Cleaning: Clean using mild soap. 6. Customer service: For further information call Pro Armor at 951-270-0559

HONDA GL1800 DRIVER BOARDS WITH HEEL/ TOE SHIFT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Place the motorcycle on its centerstand. Remove the stock foot pegs and mounts (four 6mm wrench size allen screws) 2. Beginning on the left or shift side remove the rubber cover from the shift pedal. (Some WD-40 or armor all will make it much easier). Using a hacksaw cut the retaining knob off the end of the shift pedal as shown in photo #1A. Don’t worry should you ever remove the floorboards you can replace the rubber and glue it in place. 3. Install the left floorboard assembly being sure the fork in the toe-heel shifter goes over the shift pedal. Install the two original bolts and snug them. 4. Locate the black plastic shift bushing (see photo #2A) notice the set screw on the side of the bushing slide the bushing onto the shift pedal with the small diameter going on first and engaging the fork on the toe-heel shifter. The shoulder of the bushing should be touching but not putting a side force on the fork. Rotate the bushing so that the set screw is at 9 o’clock tighten the set screw. Locate the rubber cap provided and install it over the end of the stock shift pedal. (See photo #2B). 5. Next rock or pivot the floorboard assembly up and down noting the play between the bolts and bolt holes. Position the floorboard half way between these two extremes then tighten the bolts securely. Check for clearance between the bottom of the toe shifter and the floorboard (min. 1/8″) by pushing the toe shifter down until it stops while rotating the rear wheel (see photo 2C). If there is not sufficient clearance loosen the two mounting screws and pivot the floorboard to obtain the1/8″ clearance and retighten the screws. If installing the heel shifter into one of the two optional forward mounting holes check for the 1/8″ clearance while rotating the rear wheel and up shifting. 6. On the right side remove the 12mm brake pedal mounting bolt, notice the punch mark on the pedal shaft that aligns with the slot in the pedal. The pedal MUST be re-installed in the same position. Pull the pedal outward and off the shaft. 7. See photo (3). On the bottom side of the footpad make a mark ¾” from the rear and outside edge as shown. Drill a ¼” hole thru the pedal at the mark. See photo (4) lay the brake pedal extension upside down on a bench and place the stock pedal into the opening as shown, while holding the two pieces firmly together and using the hole drilled earlier as a guide drill a ¼” hole thru the bottom of the pedal extension. Turn the two pieces over, using a needle nose pliers insert the ¼” bolt provided from the top down thru both pieces, install the lock nut provided and tighten securely. Carefully align the punch mark with the slot on the pedal and re-install the brake pedal (should the shaft slide inward you will need to remove the chrome side cover and hold the shaft outward using your finger as shown in photo (5A). Install the original 12mm bolt and tighten securely

Incoming search terms: