Honda 2007-2010 Rancher 420 ATV Rear Bumper Installation

0

Filed Under (Honda) by admin on 22-12-2011

download
Honda Rancher 420 ATV Rear Bumper (2007-2010) Installation Instructions 1. Attach top bumper attachments to top rack. 2. Attach the rear bumpers lower attachment point to vertical bars

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

Vento Rebellian 150 Brackets MiniTrike Installation Manual

0

Filed Under (Vento) by admin on 02-11-2010

download
Secure motorcycle in an upright stable position 2. Remove center stand. 3. Attach bracket A to center stand mount. 4. Remove saddle bags. 5. Insert longer bolts provided from inside saddle bag through bracket F (left)/ G (right) and attach to rear motorcycle sub frame. 6. Attach bracket D (left) / E (right) to TOP of forward MiniTrike attachment point. 7. Attach axles and wheels to MiniTrike frame and place in proper position and relation behind motorcycle. 8. Attach bottom of bracket H (left) / I (right) to rear MiniTrike frame attachment point and top of H/I to rear of brackets F/G. 9. Attach bracket B (left) / C (right) to BOTTOM of brackets D/E and TOP of attaching arm on bracket A. 10. Ensure MiniTrike is square with motorcycle and carefully tighten all bolts.

APRILIA FUTURA LEFT FRONT PANEL Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
STEP #1 Remove the left side panel & seat. STEP #2 Mount the socket. STEP #3 Route wires starting at the battery and finishing at the bracket. STEP #4 Attach the wires to the socket and test. STEP #5 Look over your work. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 – Remove the seat & the left side fairing. See the Aprilia service manual. STEP #2 – Drill a 18mm hole into the panel (11/16″ hole saw recommended and is available on our site) where shown [A]. There is plenty of room for the knee of a tall rider. An alternate position is show at [E]. There is no need to completely remove the front fairing, just unscrew the bolt under the left handgrip; the panel will flex enough to work behind it. Watch the clearance behind the panel; make sure the socket has room. Attach the socket to the panel; use a dab of Silicone on the socket and jam nut after assembly. Important: Do NOT use Loctite or over-tighten. STEP #3 – Disconnect the battery ground & positive connections. Install the fuse in the fuse-holder. Mount the fuse-holder to the round cross tube [B]. Route the harness up on the inside of the frame piggyback with the seat release cable. The harness can be inserted in the same clip that the seat- release cable uses [F]. Use wire ties to secure it from touching the engine. Connect the red wire to the positive battery posts [C]. The red rubber boot may need to be notched to allow the wire to exit. Connect the ground connection under bolt [D]. Run the black wire along the inside of the frame rail, then pass under the frame rail near the attachment point. STEP #4 -The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to terminals. Connect the red wire to the POSITIVE terminal and the black wire to the NEGATIVE terminal. Use a voltmeter to check if the polarity is correct

Incoming search terms: