Honda 300 2×4 Lift Kit Installation Instructions

0

Filed Under (Honda) by admin on 11-12-2011

download
This product is designed for us e on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400 franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain. We recommend that wider tires and/or wheel spacers be used to achieve a wider stance and to improve stability of the ATV. Riders should be advised that the handling characteristics of a taller ATV are different and require extra care when riding on side hills or off-camber situations. If you further raise the center of gravity by adding heavy loads to racks or seats, the ATV must be operated with care, at slower speeds or on relatively flat ground. Operation of an ATV with or without a lift kit, while or shortly after consuming alcohol or drugs, subjects the rider to the risk of serious bodily harm or possible death. This is compounded if the rider does not wear an approved helmet and other safety gear. High Lifter urges that all approved safety gear be worn when riding an ATV. If this is not what you expected, or is not consistent with your intended use, you should return the product immediately to the seller, before installation, for a refund of the purchase price; less any fees. After installation, product is warranted for 90 days for defects in workmanship and materials. Warranty is limited to refund of the purchase price or replacement of the kit, at the seller’s option.

Express ATVS -250cc Cobra Setup/ Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Unpacking your Cobra Installing the front shock Installing the front tires Installing rear shocks Installing the rear tires Installing seats and harnesses Steering wheel installation Roll cage installation Safety checks / Adjustments General maintenance Unpacking your Cobra First off you should pull the carton off from your new 250 Cobra cart. Inspect the cart thoroughly to make sure that your new Cobra has not been heavily damaged. You will notice that the product has a metal frame holding it in place; you may want to start removing bolts from the shipping steel frame. The next step is to remove the metal frame and lift it off of the cart. Remove any of the metal frame that may afford resistance when working on the cart it self. Be careful the metal frame may be heavy and sharp. Now would also be a good time to inspect your Cobra a little more thoroughly. In the box with the Cobra you should have found a box containing miscellaneous hardware. Installing the front shock Using some of the bolts you found in your box, install the front shocks sliding the bolt through the brackets and tighten the nut down. Next, you will need to place the ball head into the turning arm, then tighten the castle nut and insert a cotter pin so that the castle nut doesn’t loosen and become a hazard. Installing the front tires
Find the front tires and place them on the front hub and place the lug nuts on the studs. Tighten them down. Make sure that all of the lug nuts are on tightly. Installing the rear shocks Moving to the rear of the Cobra you will notice the rear shocks are not inserted. Place the rear shocks into the bracket on the rear of the Cobra. Slide one of the provided bolts through the bracket and shock eyelet and tighten the bolt down. Installing the rear tires Now that the shocks have been placed properly you can install the rear tires, place the tires onto the axle then place the rear rim lined up onto the axle and tighten the provided castle nut down. Place the cotter pin through the axle and bend off to the side. This is so the castle nut does not loosen under load. Installing the seats and harnesses
(The arrow points to an example of where the seat bolts mount) Find the two racing seats shipped in the box with the Cobra. You will need to affix them to the frame by sliding the bolts up through the bottom of the frame. This can be tricky so have patience. Once both seats have been placed in the cart and tightened find the harnesses. Once found the harnesses mount to a bracket behind the seats. Place a bolt through the bracket and bolt the harnesses down tightly. Installing the steering wheel Find the steering wheel and place it onto the steering wheel mount. Grab the six small screws and place them through the steering wheel and mount, tighten them down but also make sure the top of the wheel is facing up. Installing the roll cage

Incoming search terms:

2009 Ducati 696 Fuel Controller Installation and Operation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
this product fail to perform for either of the above reasons, two brothers racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser. to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of original purchase. We recommend that this performance part be installed by a qualified motorcycle technician. If you have any doubts as to your ability to install this performance part, please consult with your local motorcycle dealer. Read all instructions first before starting installation. Make sure the vehicle and exhaust system are completely cool before starting the installation. Also, make sure the vehicle is secure during installation. Be sure to save all stock components for possible use later. The Juice Box™ is legal ONLY for closed course race vehicles. The Juice Box™ is not applicable, nor inteded for use on EMISSIONS CONTROLLED street, highway or off-road vehicles. The Juice Box™ is not applicable, nor inteded for use on aircraft. Thank *you*for*purchasing*a*genuine*Two*Brothers*Racing* JUICE*BOX™. **This*product*represents*a*radical*step* forward *in*tuning*fuel-injected*motorcycles*and*ATVs*for* optimal *performance*using*”load-based”*technology.** We *at*Two*Brothers*Racing*hope*that*you*will*find*this* development *as*exciting*and*useful*as*we*do. **And* remember: **Proper*Fuel*=*Maximum*Power! Make *sure*the*vehicle*is*completely*cool*before*starting* the *installation. *Also, *make*sure*the*vehicle*is*secure*and* will *not*roll*around. * Remove *the*seat*assembly. * Remove *the*fuel*tank*top*cover*screws. * (fig.1) Remove *fuel*tank*top*cover. * (fig.2) Remove *side*fuel*tank*covers. * (fig.3) Remove *fuel*tank*by*removing*lower*bolt*that*secures* tank *from*sliding*rear-ward. * (fig.4)